1. Introduction
This manual provides essential information for the safe and effective use of your HOBBYWING QuicRun WP 8BL150 G2 Brushless Electronic Speed Controller (ESC). This high-performance ESC is designed for 1/8 scale RC model cars, including trucks, off-road vehicles, and monster trucks. It features robust construction, advanced technology for efficiency, and comprehensive protection functions.
Please read this manual thoroughly before installation and operation to ensure proper functionality and longevity of your ESC. Keep this manual for future reference.
Video: Overview of the HOBBYWING QuicRun WP 8BL150 G2 ESC.
2. Safety Precautions
- Always ensure correct polarity when connecting the battery to avoid damage to the ESC and battery.
- Do not operate the ESC in conditions beyond its specified limits (e.g., voltage, current).
- Keep the ESC away from moisture and extreme temperatures, despite its waterproof rating.
- Ensure all connections are secure before operation to prevent intermittent power or signal loss.
- Always disconnect the battery from the ESC when not in use.
- Children should operate RC models under adult supervision.
3. Setup and Installation
3.1 Component Overview
Figure 1: HOBBYWING QuicRun WP 8BL150 G2 ESC with power and motor wires, and electronic switch.
3.2 Connecting the ESC
- Motor Connection: Connect the three motor wires from your brushless motor to the output plugs (6.5mm gold plug female) on the ESC. Ensure correct phase connection for proper motor rotation. This ESC supports both brushless and sensored brushless motors (operates in sensorless mode).
- Battery Connection: Connect your 3-6S LiPo battery to the ESC's power input wires (Red-10AWG-150MM for positive, Black-10AWG-150MM for negative). Verify polarity before connecting.
- Receiver Connection: Plug the ESC's signal cable into the throttle channel of your RC receiver.
- Electronic Switch: The ESC includes a durable electronic switch. Mount it in an accessible location on your RC model.
3.3 BEC Output Configuration
The built-in BEC (Battery Eliminator Circuit) is adjustable, providing 6V or 7.4V output with a continuous current of 6A and a maximum current of 12A. This supports most high-voltage servos. Refer to the full PDF manual for detailed instructions on adjusting the BEC voltage if needed.
Figure 2: Upgraded BEC specifications, showing 6V/7.4V output with 6A continuous and 12A maximum current.
3.4 Programming the ESC
This ESC supports programming via an LED setting box or an LCD G2 setting box. The programming interface is shared with the fan interface. OTA programming is not supported, and firmware online upgrades are not available.
4. Operation
4.1 Powering On/Off
- Power On: Connect the battery, then press the button on the electronic switch to power on the ESC.
- Power Off: Press and hold the button on the electronic switch until the ESC powers off.
Figure 3: The durable electronic switch, designed for reliability in harsh environments.
4.2 General Usage
Once powered on and calibrated with your radio system, the ESC will control the speed and direction of your RC model's motor. Ensure your RC model is placed on a stable surface before applying throttle. Always perform a range check before operating your model at a distance.
Figure 4: The QuicRun WP 8BL150 G2 ESC integrated into an RC car chassis.
5. Maintenance
5.1 Cleaning and Storage
- After each use, gently clean any dirt or debris from the ESC, especially around the cooling fan.
- Store the ESC in a dry, cool environment away from direct sunlight and corrosive materials.
- While the ESC is waterproof (IP67 rated), avoid prolonged submersion or exposure to harsh chemicals. The IP67 rating is for splash, water, and dust resistance under normal use and may decline with wear and aging. Do not soak in water for a long time.
Figure 5: The ESC features IP67 protection for exceptional resistance to water and dust.
5.2 Cooling System
The ESC is equipped with an efficient cooling system, including a patented copper heat conduction bus bar and a cooling fan, to maintain optimal operating temperatures. Regularly check the fan for obstructions and ensure it spins freely.
Figure 6: The efficient cooling system with a copper heat conduction bus bar and integrated fan.
5.3 Capacitor Overheating Protection
The ESC features a capacitor overheating protection function to prevent damage from overload usage. This enhances the reliability and lifespan of the unit.
Figure 7: The ESC features a super large built-in capacitor (2040 uF) and capacitor overheating protection.
6. Troubleshooting
This section provides general guidance for common issues. For detailed troubleshooting steps, please refer to the official HOBBYWING support resources or contact their customer service.
- No Power: Check battery connections, ensure the battery is charged, and verify the electronic switch is properly engaged.
- Motor Not Responding: Ensure the ESC is correctly connected to the receiver's throttle channel. Check motor wire connections and confirm the motor type is compatible (brushless).
- Erratic Operation: Check for loose connections, signal interference, or issues with the receiver/transmitter.
- Overheating: Ensure adequate airflow around the ESC. Check for excessive load on the motor or incorrect gearing. The built-in cooling system and capacitor protection should mitigate most overheating issues under normal conditions.
7. Specifications
| Feature | Specification |
|---|---|
| Product Name | QuicRun WP 8BL150 G2 |
| Scale | 1/8th |
| Brush/Brushless | Brushless |
| Sensor Type | Sensorless (operates in sensorless mode for sensored motors) |
| Waterproof | IP67 Rated |
| Continuous Current | 150A |
| Peak Current | 960A |
| Battery Cells | 3-6S LiPo |
| BEC Output | Switch Mode 6V/7.4V @ 6A (Continuous), 12A (Max) |
| Power Cord | Black-10AWG-150MM, Red-10AWG-150MM |
| Output Plug | 6.5mm Gold Plug Female |
| ESC SET Key | Not supported |
| LED Setting Box | Supported |
| LCD G2 Setting Box | Supported |
| OTA Programmer | Not supported |
| Programming Interface | Shared with fan interface |
| Firmware Upgrade | Not supported online |
| Dimensions (L*W*H) | 60*48*40.4mm |
| Weight | 169.5g (including wire) |
| Supported Motor Types | Brushless motor / Sensored brushless motor (sensorless mode only) |
| Applicable Models | 1/8 truck/off-road vehicle/monster truck |
| Applicable Motor Size | 4268, 4274 size motor |
8. User Tips
- Compatibility Check: Always verify that the ESC's specifications (e.g., battery voltage, motor type, motor size) perfectly match your RC model's requirements for optimal performance and safety.
- Secure Connections: Ensure all electrical connections are tight and properly insulated to prevent shorts and power interruptions.
- Programming for Performance: Utilize the LED or LCD G2 setting box to fine-tune ESC parameters for your specific driving style and track conditions.
9. Warranty and Support
For detailed warranty information, technical support, or specific programming guides, please refer to the official HOBBYWING website or contact their authorized distributors. A general user manual PDF is available at this link, however, please note that this specific PDF is for drone accessories and may not contain detailed information for this ESC model. Always seek the most relevant documentation from the manufacturer.