Introduction
This manual provides instructions for the assembly, use, and maintenance of your DayPlus 5-Tier Boltless Garage Shelving Unit. This heavy-duty shelving unit is designed for storage and organization in various environments such as garages, sheds, utility rooms, warehouses, workshops, homes, kitchens, or offices.
The unit features a sturdy metal steel frame and moisture-resistant MDF boards, designed for durability and long-lasting use.
Safety Information
- Always wear gloves when assembling the unit to prevent injury.
- Never exceed the maximum shelf load of 175 kg (386 lb) per tier or the maximum load for the complete unit array (875 kg).
- The load on the shelves must be evenly distributed to prevent damage to the wooden boards and ensure stability.
- The unit is not suitable for rooms with elevated humidity, as this could cause damage to the wooden boards.
- For your safety, the shelf unit must always be assembled with suitable wall mounting.
- Only erect the unit on horizontal, smooth floors; otherwise, stability and maximum load-bearing capacity may not be guaranteed.
- When assembling, do NOT drill into water or electrical conduits.
- Examine the product for transport damage before assembling. No liability is accepted for damage to a product that has already been assembled if defects were present prior to assembly.
Package Contents
Before assembly, ensure all components are present and undamaged. If any connector tabs on the shelf cross pieces are bent, they can be carefully bent back into position using a flat head screwdriver.
Figure 1: Component Check List Diagram
| Component | Quantity |
|---|---|
| Half Upright | 8 |
| Front/Back Bar | 10 |
| Side Bar | 10 |
| Support Bar | 5 |
| Deck (MDF Board) | 5 |
| Upright Connector | 4 |
| Foot (Rubber Feet) | 8 |
Setup and Assembly
The shelving unit features a boltless design for quick and easy assembly. No screws or bolts are required; parts slide together and can be secured with a rubber hammer (not supplied).
Assembly Video Guide
Video 1: Step-by-step assembly guide for the DayPlus shelving unit.
Step-by-Step Assembly Instructions
- Read all advice and safety instructions carefully before beginning assembly.
- Remove all packaging materials and verify all components against the Component Check List.
- Assemble the product on a clean and smooth surface (e.g., a carpet) to prevent scratching the finish.
- Begin by connecting the uprights and beams. Push the inside buckle downward to secure the connection. Ensure the card is buckled inward.
- Install the middle beams, paying attention to bend them slightly for proper fit.
- Follow the previous steps to install the upper part of the frame.
- Once the frame is assembled, install the floor mats (rubber feet) onto the bottom of the uprights for floor protection and stability.
- Install extension clips to connect the upper and lower sections of the uprights if assembling a full-height unit.
- Place the MDF boards onto the assembled frame, ensuring they sit securely within the beams.
- Use a rubber hammer to gently tap components into place and ensure a snug fit, avoiding damage to the finish.
Figure 2: Detailed assembly steps and warnings.
Figure 3: Close-up of the boltless connection mechanism.
Figure 4: Installation of rubber feet for floor protection.
Operating and Usage
Adjustable Shelf Height & Layout
The five solid MDF shelves are adjustable, allowing you to customize the height to suit your storage needs. The unit can also be split into two smaller units (a 3-shelf and a 2-shelf unit), configured as a workbench, or arranged as a corner unit, offering versatile storage solutions.
Figure 5: Examples of adjustable shelf heights and split configurations.
Figure 6: The shelving unit configured as two separate workbenches.
Load Capacity
Each individual shelf can hold up to 175 kg (386 lb), with a total maximum capacity of 875 kg for the entire 5-tier unit. Ensure weight is evenly distributed across each shelf to maintain stability and prevent damage.
Figure 7: Dimensions and maximum load capacity per shelf.
Maintenance
To clean the shelving unit, simply wipe it with a dry cloth. Avoid using harsh chemicals or excessive moisture, especially on the MDF boards, as this could cause damage.
The metal frame has a rust-resistant coating, but prolonged exposure to high humidity should be avoided to maintain its condition.
Troubleshooting
Stability Issues
If the unit feels unstable after assembly, ensure it is erected on a horizontal, smooth floor. Verify that all connections are securely fastened. For optimal safety and stability, especially when storing heavy items, the shelving unit MUST be fixed to a wall using suitable wall plugs and retaining screws (not supplied). This prevents the racking from tipping over.
Difficulty Assembling
If you encounter difficulty connecting components, ensure the connector tabs are not bent. They can be gently adjusted with a flat head screwdriver. A rubber hammer can be used to tap components into place for a secure fit.
Specifications
| Feature | Detail |
|---|---|
| Type | 5-Tier Shelving Unit |
| Colors Available | Silver, Black, Red, Blue |
| Material | MDF Board & Steel Frame |
| MDF Board Thickness | 5mm |
| Size-1 (H*W*D) | 150cm x 70cm x 30cm |
| Weight (Size-1) | 9.42kg |
| Size-2 (H*W*D) | 180cm x 90cm x 40cm |
| Weight (Size-2) | 14.42kg |
| Max. Capacity per Tier | 175kg (386 lb) |
| Total Max. Capacity | 875kg |
| Assembly Type | Boltless |
| Convertibility | Can be split into 2 workbenches |
User Tips
- Always secure the racking unit to a wall, especially when storing heavy items, to ensure stability and prevent accidental tipping.
- Consider the color options available (Silver, Black, Red, Blue) to best match your space.
Warranty and Support
For any questions regarding your DayPlus shelving unit, please contact the seller or manufacturer directly. Keep your purchase receipt for warranty claims, if applicable.