Introduction
This manual provides detailed instructions for the safe and effective use of your Sytong FM06 and XM06 series thermal imagers. These devices are designed for various outdoor applications, including travel, camping, animal observation, marine observation, and security protection. Please read this manual thoroughly before operating the device to ensure optimal performance and longevity.
What's in the Box
Upon unpacking your Sytong thermal imager, please verify that all the following items are included:
- Thermal Imaging Sight
- User Manual
- Mount (with screws and hex-nut wrenches)
- Type-C Cable
- 5V 2A Adapter
- Handbag
- Battery

Product Overview
Device Components

| No. | Component |
|---|---|
| 1. | Objective Lens |
| 2. | Lens Focusing Ring |
| 3. | Record Button (REC) |
| 4. | Navigation UP Button |
| 5. | MENU Button |
| 6. | Navigation DOWN Button |
| 7. | Dioptre Adjustment Ring |
| 8. | Eyeshade |
| 9. | Red Laser Pointer |
| 10. | Laser Rangefinder |
| 11. | Power (ON/OFF) Button |
| 12. | Data Compartment |
| 13. | Lens Cover |
| 14. | Device LED Indicator |
| 15. | Battery Cap (Make sure to tighten the battery cover before using the device) |
Button Legend

- Power (ON/OFF) Button: Hold for 3 seconds to power off. Hold for 1-2 seconds to enter sleep mode. The LED indicator will turn off after power off. Wake the device by pressing the power (ON/OFF) button. Press the power button to refresh the device.
- Record Button (REC): When not in menu mode: Press to switch the reticle profiles. Hold for 1.5-3 seconds to take a picture. Hold for 3 seconds to record a video or stop recording.
- Navigation UP Button: In menu mode: Press to switch menu items upwards. When not in menu mode: Press to change operating mode. Hold to turn on or off the Picture in Picture function.
- MENU Button: In menu mode: Press to confirm selection. Hold to exit main menu or submenu. When not in menu mode: Press to enter menu. Hold to turn on or off the red laser pointer. When LRF is on: Press to lock or unlock rangefinding values.
- Navigation DOWN Button: In menu mode: Press to switch menu items downwards. When not in menu mode: Press to change set-up zoom (1x, 2x, 4x, 8x). Hold to turn on or off laser rangefinder.
Setup
Battery Installation
Please use a lithium chargeable 3.7V flat battery 18650. Remove the battery compartment cap and ensure the positive pole is oriented inwards. Replace the cap and screw it until tight. Failure to do so may result in restarting issues.

Mount Installation
Attach the mount to the base of the scope using a hex-nut wrench and screws. The mounting holes in the base of the scope allow the mount to be installed in multiple positions. Choose the mounting position that ensures the correct eye relief for your device type. The scope is ready to be installed on a device and zeroed. Before using the device, please follow instructions in the "Reticle Adjustment (Zeroing)" section.

App Connection
To connect your device to the mobile app:
- Download the APP by scanning the QR code provided below, according to your mobile phone system.
- Turn on WiFi on both the XM device and your phone.
- Enter the APP.
- Choose the WiFi network "APPshow-XMLRF-XXX" to connect. The default password is 12345678.
Live images will be displayed on the App after your phone is connected to the device's WiFi.

Operating Instructions
Quick Start: Power On and Image Settings
- Hold the power (ON/OFF) button (11) for 3 seconds to power on.
- Rotate the dioptre adjustment ring (7) to get a clear image of the icons on the display.
- Rotate the lens focusing ring (2) to get a clear image of the observed object.
- Press the navigation UP button (4) to select the operating modes (White Hot, Sky Mode, Black Hot, Red Hot, Fusion).
- Press the navigation DOWN button (6) to select digital magnification (1x, 2x, 4x, 8x).
- Press the MENU button (5) to enter the menu to select the appropriate parameter.
- Hold the power (ON/OFF) button (11) for 3 seconds to power off. The LED indicator will be turned off after the device is powered off.
Menu Functions
| Number | Main Menu Description | Sub Menu Description |
|---|---|---|
| 1 | Operating Modes | Options: "White Hot" / "Sky Mode" / "Black Hot" / "Red Hot" / "Fusion". Default mode is "White Hot".![]() |
| 2 | Video Output | Options: "On" / "Off". The video output function CVBS will be on/off accordingly. |
| 3 | WiFi | Options: "On" / "Off". Turn on WiFi on both the device's Menu and user's phone. On user's phone, find and connect to "APPshow-XMLRF-XXX" WiFi network with password 12345678. Live image will be displayed on the App after the phone is connected to the device's WiFi. |
| 4 | Picture In Picture | Options: "On" / "Off". |
| 5 | Reticle Type | Options: Off / Select the preferred reticle type from 8 choices. |
| 6 | Reticle Color | Options: Black, White, Gray, Red, Green. |
| 7 | Reticle Profiles | Select one of the saved profiles (Max. 10 profiles). |
| 8 | Reticle Adjustment (Zeroing) | Freeze the image by pressing the MENU button. Move the reticle horizontally or vertically with the UP/DOWN buttons. Switch between horizontal and vertical adjustments by pressing REC button. After the reticle matches the point of impact, press the MENU button to save the position. Input the target distance and select the unit (Meter/Yard). The reticle profile will be saved with the distance as its name. |
| 9 | Gyro | Options: On/Off. |
| 10 | Laser Rangefinder Unit | Options: Meter/Yard. |
| 11 | Laser Rangefinder Mode | 1. Single distance measurement. 2. Continuous distance measurement. |
| 12 | OLED Brightness | Options: 1-10. |
| 13 | Target Brightness | Options: 1-10. |
| 14 | Contrast Ratio | Options: 1-10. |
| 15 | Image Detail Boost | Options: 1-5. |
| 16 | Date/Time | Move the options by pressing the MENU button. Change the value using the UP/DOWN button. Confirm the values by pressing the MENU button. Quit by holding the MENU button. |
| 17 | Language | Options: English/Chinese/Other Languages. |
| 18 | Record Audio | Options: On/Off. Default is off. |
| 19 | Format | Options: Confirm/Cancel. |
| 20 | Auto Power Off | Options: 3 Min / 5 Min / Off. Default: Off. |
| 21 | Default | Options: Confirm/Cancel. |
| 22 | Pixel Cure | Select "Pixel Cure" and press MENU button to get to the submenu. The lens should be covered with a lens cover before performing the pixel cure. Press the MENU button and follow the prompts to fix the bad pixels. After repair, please remember to save it. Hold the UP/DOWN button to move X/Y position. Press the Power button to switch between X/Y/Save. |
| 23 | Image Adjustment | Select "Image Adjustment" in the main menu. Press MENU button to select "Confirm" and cover the lens if image adjustment is required. |
| 24 | Auto Ballistic Calculator (BC) | Select BC and press the MENU button to get to the sub menu: On/Off/Setting. Press 【Record Button】 to move to set parameters. Press 【Up/Down Button】 to set values. |
| 25 | Version | Select "Version" to view the device's software version. |
Using The Integrated Laser Rangefinder
- Hold the power (ON/OFF) button (11) for 3 seconds to power on the device.
- Hold the navigation DOWN button (6) for 3 seconds to activate the laser rangefinder.
- The rangefinder indicator (a small box) will appear at the center of the display.
- Point the rangefinding indicator at an object to measure the distance (the distance will be displayed at the top right corner of the display).
Red Laser Pointer Adjustment
Hold the MENU button to turn on/off the red laser pointer. Adjust the position of the red laser pointer by using an inner hexagon wrench.
Connect to a Computer
Turn off the device and connect to the computer with a Type-C cable. Hold the power button to turn on the device. The computer will read the memory card of the device.
Power Adapter
Used only to charge batteries equal to or below 5V/2A.
Maintenance
- Keep the device clean. Use a soft, dry cloth for general cleaning.
- For lens cleaning, use a specialized lens cleaning cloth and solution to avoid scratches.
- Ensure the battery compartment cap is always tightly secured to prevent moisture ingress.
- Store the device in its handbag in a cool, dry place when not in use.
- Avoid exposing the device to extreme temperatures or direct sunlight for prolonged periods.
Troubleshooting
- Device not powering on: Ensure the battery is correctly installed with the positive pole inwards and fully charged. Check that the battery cap is tightened.
- Unclear image: Adjust the dioptre adjustment ring (7) for display clarity and the lens focusing ring (2) for object clarity.
- WiFi connection issues: Ensure WiFi is enabled on both the device and your phone. Verify the correct network name ("APPshow-XMLRF-XXX") and password (12345678).
- Bad pixels on display: Use the "Pixel Cure" function in the menu as described in the Menu Functions section.
- Laser Rangefinder not working: Ensure the device is powered on and hold the navigation DOWN button (6) for 3 seconds to activate it.
Specifications
Sytong XM06-LRF Specifications

| Sensor | |
|---|---|
| Type | Uncooled |
| Frame Rate | 50 Hz |
| NETD | <25mk |
| Resolution | 640x512 Super Sensitive |
| Pixel Size | 12µm |
| Optical Characteristics | |
| Objective Lens | F35mm/50mm |
| Digital Zoom | 1x / 2x / 4x / 8x |
| Dioptre Adjustment | +5/-5 D |
| FOV | 12.5°x9.4° / 8.8°x6.6° |
| Magnification | 1.7X / 2.5X |
| Eye Relief | 50 mm |
| Focus Scope Range | 5m~∞ |
| Display | |
| Operating Mode | White Hot, Sky Mode, Black Hot, Red Hot, Fusion |
| Type / Resolution | 0.39 inch / OLED / 1024x768 |
| Operational Characteristics | |
| 3D Gyroscope | Yes |
| Power Supply | 3-4.2 V |
| Waterproof Rating | IP67 |
| Battery | 18650 / 3500mAh |
Sytong FM06-LRF Specifications

| Sensor | |
|---|---|
| Type | Uncooled |
| Frame Rate | 50 Hz |
| NETD | <30mk |
| Resolution | 384x288 Super Sensitive |
| Pixel Size | 12µm |
| Optical Characteristics | |
| Objective Lens | F35mm/50mm |
| Digital Zoom | 1x / 2x / 4x / 8x |
| Dioptre Adjustment | +5/-5 D |
| FOV | 7.5°x5.7° / 5.3°x4.0° |
| Magnification | 2.8X / 4X |
| Eye Relief | 50 mm |
| Focus Scope Range | 5m~∞ |
| Display | |
| Operating Mode | White Hot, Sky Mode, Black Hot, Red Hot, Fusion |
| Type / Resolution | 0.39 inch / OLED / 1024x768 |
| Operational Characteristics | |
| 3D Gyroscope | Yes |
| Power Supply | 3-4.2 V |
| Waterproof Rating | IP67 |
| Battery | 18650 / 3500mAh |
General Specifications

| Power & Environmental | |
|---|---|
| External Power Supply | 5V (USB) |
| Operating Time (At Temperature =22℃) | 8 hours |
| Operating Temperature | -20℃ to +50℃ |
| Max. Recoil Power, Joules | 10000 |
| Dimensions | 224x92x69mm |
| Weight (Without Battery/Mount) | 668g |
| Video Recorder | |
| Video / Photo Resolution | 1024x768 |
| Video / Photo Format | .mp4 / .jpg |
| Supported Memory Type | Built-in 32G Memory Card |
| Wifi Channel | |
| Frequency | 2.4GHz |
| Standard | 802.11 b/g |
| WiFi Signal Range | 15m |
| Rangefinder | |
| Wavelength | 905nm |
| Max. Measuring Range | 1200m |
| Measuring Accuracy | +/-1m |
| Detection Distance (Target Size: 1.7m x 0.5m) | 1750m / 2500m |
User Tips
- Battery Life: To maximize battery life, consider using the sleep mode when temporarily not observing. Always carry a spare charged battery for extended use.
- Environmental Conditions: While the device is IP67 waterproof, avoid submerging it. Extreme cold can affect battery performance; keep batteries warm if possible.
- Zeroing: Proper zeroing is crucial for accurate rangefinding and reticle use. Take your time with the reticle adjustment process.
- App Features: Explore the mobile app for additional features like live streaming, recording management, and advanced settings.
- Firmware Updates: Periodically check the official Sytong website for any firmware updates that may improve performance or add new features.
Warranty and Support
For product support, warranty information, and to learn more about Sytong products, please visit our official website or scan the QR code below.

Website: https://www.sytong2013.com
