Acceo A45P 4K Dashcam User Manual

1. Introduction

About This Guide

We make every effort to ensure the accuracy of this user guide, but we cannot guarantee that the content is entirely correct. Specifications and other details may differ slightly due to ongoing product improvements.

Product Overview

• The dimensions shown in this manual are approximate values.
• Illustrations are for illustrative purposes only and may differ from the actual ones.
• The specifications and appearance of this product are subject to change without notice for improvement.
• After taking out the packaging materials, dispose of them properly or recycle them according to the regulations of the local government.

2. Setup and Installation

General Installation Notes

1. Since the machine moves during transportation, it is attached with a protective film to prevent damage. Before use, please record some videos to test the camera's quality.
2. Use only the original power supply. Using another brand of power supply may damage or burn the equipment.
3. If you want to use the parking monitoring or motion detection function, you need to use a buck line (Hardwire kit) to connect the video recorder to the car battery (the buck line is sold separately).
4. Install this unit near the rear-view mirror so that you can record a wide-angle landscape at its maximum.
5. Ensure that the lens is within the wiper's range so that you can record clearly even in the rain.
6. Do not touch the lens with your finger. Finger oil can remain on the lens, causing unclear video or still images. Clean the lens regularly with a soft cloth to remove dust. Avoid chemical detergents, gasoline, alcohol, or anti-static sprays.
7. This product is suitable for most cars. For trucks, pay attention to the length of the car charger line.
8. Please scan the provided QR code to watch our installation video before installing the video recorder. It is highly recommended to ask a professional auto mechanic to complete the installation at an auto shop.

Product Components

Below is a diagram illustrating the main parts of the dashcam and its ports.

• TF Card Slot
• Rear Camera Interface
• Power Input
• Reset Button
• Power Button

Rear Camera Installation

Connect the rear camera's red cable wire with your car's reverse lamp positive pole (+). Then, plug the car charger into the cigar lighter to power the car DVR. When you shift your car into Reverse Gear, the car DVR will automatically switch to the rear camera with parking lines, enabling the auto-reversing function.

Buck Line Installation (for 24H Parking Monitoring)

The buck line is used to provide continuous power to the DVR for 24-hour parking monitoring without occupying the cigarette lighter interface. You will need to find two fuse slots for this step:

1. A fuse slot that provides constant power (RED wire will go here).
2. A fuse slot that only provides power when you turn your key to the ACC position (YELLOW wire will go here).
3. Connect the BLACK wire to the grounding screw or bolt.

Installation Video Guide

For a visual guide on installation, please watch the official product video:

Packing List (Example Configurations)

The contents of your package may vary depending on the specific configuration purchased. Below are examples of common packing lists:

DVR with 6M SONY RC

• 1 x DVR
• 1 x Power charger
• 1 x User Manual
• 2 x Bandage
• 1 x USB Card Reader (Gift)
• 1 x 1080P Sony Rearview Camera With 6 Meters Cable

DVR with 6M SONY RC-BL

• 1 x DVR
• 1 x Power charger
• 1 x User Manual
• 2 x Bandage
• 1 x USB Card Reader (Gift)
• 1 x 1080P Sony Rearview Camera With 6 Meters Cable
• 1 x Buck Line

DVR with 6M SONY RC-GPS

• 1 x DVR
• 1 x Power charger
• 1 x User Manual
• 2 x Bandage
• 1 x USB Card Reader (Gift)
• 1 x 1080P Sony Rearview Camera With 6 Meters Cable
• 1 x GPS Module

DVR with 6M SONY RC-BL-GPS

• 1 x DVR
• 1 x Power charger
• 1 x User Manual
• 2 x Bandage
• 1 x USB Card Reader (Gift)
• 1 x 1080P Sony Rearview Camera With 6 Meters Cable
• 1 x Buck Line
• 1 x GPS Module

3. Operating Instructions

Power Button Functions

1. As a power switch:
   • Start up: Press and hold the Power Button for 2 seconds to turn on the video recorder. The machine will start working automatically.
   • Shut down: Press and hold the Power Button for 2 seconds to automatically save the video file and user settings. The video recorder will shut down.
2. To turn on/off the display: Press the Power Button in the power-on state to turn the display black, and press again to turn it on.

Touch Buttons and Menu Functions (Main Interface)

1. Locking (EMR emergency): In video mode, click the add-lock sign "🔒" to add the current video as a locked file (20 seconds before and after the event). Click the unlock icon "🔓" to unlock the current file.
2. Audio switch: Click to turn the recording function on or off. The setting will be automatically saved.
3. Video recording: The default icon in video state is "🔴", in non-video state is "⚪". Click to change the video status.
4. Take photo when recording: Click "📷" to take a photo.
5. Playback interface: Click "▶" to enter the playback interface.
6. Setting interface: Click "⚙️" to enter the settings interface.
7. Recording icon: "🔴" flashing indicates normal recording. Non-recording status will hide the icon.
8. Recording time (Loop Record): Under normal recording, the recording time is displayed (default 1 minute). You can change the cycle recording time in settings. Non-recording status will hide.
9. Resolution: Displays current video resolution (default 4K/2.5K/1080P/720P). Can be changed in settings.
10. Time: Displays current RTC time, which can be set in settings.
11. Brightness adjustment: Slide up/down or swipe right/left to adjust brightness.
12. Brightness icon: "+" "-" indicates brightness.
13. License plate: Can be set in the settings interface.
14. WIFI icon: Enabling WIFI displays a white WIFI icon. It turns green when connected to the mobile app.
15. WiFi APK download: Go to settings, find WiFi, click it, then scan the QR code to download the APK.
16. GPS icon: When the GPS module is plugged in, a white GPS icon is displayed. It turns green when receiving a signal.
17. GPS speed: When GPS receives a signal, the GPS icon is green and GPS speed is displayed. Note the difference between km/h and mph.
18. G-Sensor: OFF/LOW/MIDDLE/HIGH. With built-in G-sensor, the dash camera automatically detects sudden shake/collision and locks footage to prevent overwriting.
19. Parking Monitor: OFF/LOW/MIDDLE/HIGH. When activated, the dash camera automatically turns on and records when vibration is detected, or captures frames for a time-lapse video for 20 seconds.
20. Time lapse recording: Four forms: off, 5 hours, 12 hours, 24 hours. Default is off. If ACC disconnects, the recorder prompts "Enter Video Recording" and enters streaming. Screen turns off after 5 seconds. If touch occurs, it turns off again after 10 seconds. When ACC is powered on, it exits video recording.
21. Stream Media: OFF/ON. When "on", rear camera is full screen by default. When "off", front camera is full screen by default.
22. Language: Multi-language. Contact support for new firmware if more languages are needed.
23. Time zone selection: Set local time zone.
24. Screen sleep: Off, 10s, 30s, 3 minutes. Default is off. Screen turns off after no touch. Recording continues even when screen is off.
25. Format SD: Format the TF card. Always format Micro SD card before use.
26. Factory reset: Dialog box appears to confirm factory settings recovery.

Main Interface Screen Operation

• Slide up and down: Change the display position of the current camera video screen. Operation is saved after dragging.
• Sliding left and right: Change the current video display source (front view, rear view, split screen). Sliding left/right on the brightness part adjusts brightness. Operation is saved after sliding.

Playback Interface

1. File list interface: Click 'Playback icon' to enter the playback interface and video file interface (front camera by default).
2. Video file mode: Click to view normal recording files. Front and rear camera files are saved in "front_norm" and "back_norm" folders.
3. Lock file mode: Click to view locked video files. Front and rear camera locked files are saved in "front_emr" and "back_emr" folders.
4. Photo file mode: Click to view and store photo files. Front and rear camera photo files are saved in "front_photo" and "back_photo" folders.
5. Front and rear camera switching: Switch between front and rear camera files under the current file.
6. Delete: Select desired file, click delete icon to confirm.
7. Files within the grid: Swipe up/down to select file, then enter playback interface.
8. Return: Return to the main interface.
9. Select All: Select all files.

Key Features Visuals

4. Maintenance

Cleaning the Lens

Do not touch the lens with your finger. Finger oil can remain on the lens, causing unclear video or still images. Clean the lens regularly with a soft cloth to remove dust. Be careful not to use chemical detergents, gasoline, alcohol, or anti-static sprays to clean the product.

SD Card Management

Always format the Micro SD card before its first use and periodically to maintain optimal performance. Refer to the 'Format SD' section in the operating instructions for details.

5. Troubleshooting (Frequently Asked Questions)

1. What if the dash cam cannot be turned on?
   • Plug in the car charger and try to turn it on by pressing the On-Off key for about 3 seconds.
   • Charge the dash cam for about 5 minutes before turning it on, then manually restore factory settings.
   • Press the Reset button through the pin to restore factory settings.
2. What if the dash cam turns on or off automatically?
   • The dash cam needs to be plugged into the car charger for use. The built-in battery has small capacity and is mainly used for parking monitor mode to record important videos.
   • Support Class 10 or above Micro SD Card. Please format the card before use.
3. What if the product cannot read the card?

   Please use a genuine Class 10 or above Micro SD Card. Format the SD Card on the computer before use, and then insert the card correctly (there will be slight rebound resistance when inserted correctly).
4. What if the video function cannot be used normally?

   Please format the micro SD card in the dash cam before using. Support 16GB/32GB/64GB/128GB micro SD card, Class 10 or above is recommended.

5. What if the product cannot be used normally after working for a period of time?
   • It is possible that the G-sensor function is set, leading to too many locked files and preventing loop recording. Manually delete locked files.
   • Check if the G-sensor sensitivity is set to High. If too high, files might be locked due to road bumps and prevent overwriting. Set G-sensor from high to medium or low.
   • Use motion detection only when not driving.
6. What if the rear camera doesn't work?
   • The rear camera is not connected properly. Check whether the rear camera is connected correctly.
   • The rear camera's wiring is not connected tightly, or there is a loose contact at the interface. Check whether the rear camera's connection is normal.
7. What if the image from the rear camera is upside down?

   The rear camera is installed in the wrong direction. Adjust to the correct installation mode.

8. What if the screen turns black after turning it on for about one minute?

   The Screen Dormant function is turned on in settings. Please turn off this function.

9. What if the product cannot set the date and time correctly?

   Ensure the product has enough power. Enter system settings, find the date and time option, and set it. After setting, manually turn off the dash cam to complete the date and time setting.
10. Why does the product automatically heat up?
    • The product has been used for a long time.
    • The temperature in the car is too high.
11. Recordings have wrong date/time (e.g., January date)?

    Set the date and time through the settings menu. After setting, manually turn off the dash cam. Time setting is completed.

12. The recorded image is not clear?
    • There is a protective film on both front and rear camera lenses. Peel off both films before use.
    • Check if the windshield is clean.
13. The sound of the button is very noisy?

    Select "OFF" for the operation voice (OFF/ON) button in the system settings (Optical).

6. Specifications

7. User Tips

• WiFi Connectivity: The dashcam supports WiFi connectivity, allowing you to connect to your smartphone. Through the dedicated app, you can view recorded videos, take photos, playback footage, and adjust various settings directly from your phone.
• SD Card Quality: Always use a high-quality Class 10 Micro SD card (16GB to 128GB) for reliable recording. Low-quality or slow SD cards may cause recording issues.
• G-Sensor Sensitivity: If you experience frequent locked files or issues with loop recording, check your G-sensor sensitivity settings. Adjust it from High to Medium or Low to prevent unnecessary file locking due to road bumps.
• Parking Monitor: For 24-hour parking monitoring, ensure you install a buck line to provide continuous power to the DVR. This feature helps protect your vehicle when parked by recording events triggered by impacts.

8. Warranty and Support

Warranty Information

• 30-Day Money-Back Guarantee: For 30 days after the date of purchase, you may return your undamaged product for a full refund for any reason.
• 12-Month Warranty for Quality-Related Issues: For 12 months after the date of purchase, we will handle all quality-related issues with a replacement or full refund.

Friendly Reminder: Make sure to read this user manual thoroughly and use the product as instructed. When contacting us for help, please have your product handy for troubleshooting.

Limitations

Our returns and exchange service is limited to purchases made from Authorized stores. If you purchased through a different retailer, please contact them directly. Unauthorized reselling of our products is prohibited.

Contact Information

Website: www.e-ace.cn
Email: fireking@e-ace.cn
Phone: +86 0755-8464 4084
Tel (WhatsApp): +86-18127083357
Address: Floor 2nd, No.1 Yuanxia street, Pingshan District, Shenzhen City, Guangdong Province, 518000, China