KKMOON ST4100/ST4800

Contents

SMART SENSOR Ground Earth Resistance Tester Multifunction Digital Clamp Meter

Models: ST4100 / ST4800

1. Introduction

The SMART SENSOR Ground Earth Resistance Tester is a clamp-shaped instrument designed for accurate detection of ground resistance. Controlled by a microprocessor, it utilizes rapid filtering technology to minimize interference, ensuring precise measurements. This device is an essential tool for professionals in telecommunication, electric power, meteorology, engine room maintenance, oil field operations, electromechanical installation, and various industrial enterprises requiring electrical power system analysis.

It is suitable for measuring ground resistance in a wide range of applications, including telecommunications infrastructure, power distribution lines, transmission towers, gas stations, factory grounding networks, and lightning protection systems.

Clamp meter in an electrical environment
Figure 1: The clamp meter in an electrical testing environment.

2. Safety Information

WARNING: Always read and understand all safety instructions before operating the device. Failure to do so may result in electric shock, fire, or serious injury.

  • This device complies with safety regulations IEC61010-1 (CAT III 300V, CAT IV 150V, degree of pollution 2), IEC61010-031, and IEC61557-1 (earthing resistance).
  • Do not use the device if it appears damaged or is operating abnormally.
  • Ensure the battery compartment is securely closed before use.
  • Do not attempt to measure circuits with voltages exceeding the specified limits.
  • Avoid using the device in wet environments or during electrical storms.
  • Always wear appropriate personal protective equipment (PPE) when working with electrical systems.
  • Keep the device away from strong magnetic or electric fields to prevent measurement interference.

3. Product Overview

3.1 Package Contents

Upon unpacking, please verify that all items listed below are present and undamaged:

  • 1 x Earth Resistance Tester (ST4100 or ST4800 model)
  • 1 x Aluminum Carrying Case
  • 1 x Measuring Ring (Calibration Loop)
  • 1 x User Manual (English)
Contents of the product package including the clamp meter, aluminum case, measuring ring, and user manual.
Figure 2: Product package contents.
The clamp meter stored inside its aluminum carrying case.
Figure 3: Clamp meter stored in its aluminum case.

3.2 Key Features

  • Easy to Operate: Designed for user-friendly operation, allowing ground system measurements without disconnecting the ground wire or requiring auxiliary electrodes.
  • Precision Clamp Head: Features a precision iron core and winding for stable, accurate measurements with strong anti-interference capabilities. The clamp size is Φ1.26" (32mm), with large jaws and double insulation for enhanced safety.
  • Data Storage: Capable of recording up to 500 sets of measurement data. A flashing "MEM" symbol indicates when storage is full.
  • Multi-functional: Includes real-time clock, data storage, data access, alarm function, and automatic shutdown.
  • HD LCD Backlit Display: Ensures clear readability in various lighting conditions, from bright sunlight to darkness.
  • Alarm Function: Provides an audible alarm when the measured value exceeds a user-defined alarm set point.
A hand holding the clamp meter, demonstrating its use on a cable for measurement.
Figure 4: Demonstrating the precision clamp head in use.
Close-up of the HD LCD Backlit Display, showing clear readings in a low-light environment.
Figure 5: HD LCD Backlit Display for clear readings.
Illustration of the alarm function, showing a lightning bolt and an alarm prompt on the clamp meter's display.
Figure 6: Alarm Function in action.

4. Setup

4.1 Battery Installation

  1. Ensure the device is powered off.
  2. Locate the battery compartment cover on the back of the device.
  3. Open the battery compartment cover.
  4. Insert four (4) 1.5V AA dry batteries (not included), observing the correct polarity (+/-) as indicated inside the compartment.
  5. Close the battery compartment cover securely.

4.2 Initial Power-On

Press the power button (Power Symbol) to turn on the device. The LCD will illuminate, and a self-test sequence may run. The battery power level will be displayed in real-time on the screen.

5. Operating Instructions

5.1 Measurement Modes

Press the MODE button to cycle through different measurement functions: Grounding Resistance Test, Circuit Resistance Test, and Leakage Current Test (ST4800 only).

5.2 Performing a Measurement

  1. Select the desired measurement mode using the MODE button.
  2. Open the clamp jaws by pressing the lever.
  3. Carefully place the conductor (e.g., grounding wire) within the clamp jaws, ensuring it is fully enclosed.
  4. Release the lever to close the jaws securely around the conductor.
  5. The measurement will be displayed on the LCD. The Ω and A symbols will be displayed synchronously on the screen.

For ground system measurements with a loop, there is no need to disconnect the ground wire or use auxiliary electrodes, making the process safer and faster.

5.3 Data Storage and Access

  • Store Data: After a measurement, press the MEM button to save the current reading. The device can store up to 500 groups of data. A flashing "MEM" symbol indicates that the storage is full.
  • Access Data: Press the MR button to review stored data. The "MR" symbol will be indicated on the display. Use the arrow buttons (if available, or cycle through MEM button) to navigate through stored records.
Illustration of the 'One Click Storage' feature, showing data being saved to memory on the clamp meter's display.
Figure 7: One Click Storage function.

5.4 Alarm Function

  • Set Alarm: Press the SET button to enter the alarm setting mode. Use the AL button and other navigation buttons (if applicable) to adjust the alarm threshold.
  • Alarm Trigger: If a measured value exceeds the set alarm point, the device will emit an audible alarm.

5.5 Auto Shut-Off

The device features an automatic shut-off function to conserve battery life. It can be set to 5, 10, 15, or 20 minutes. Selecting "OFF" will disable the automatic shutdown. The default setting is 5 minutes. To adjust, refer to the detailed instructions in the full user manual.

5.6 Data Hold

Press the HOLD button to freeze the current reading on the display. Press HOLD again to release and resume live measurements.

6. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the device. Do not use abrasive cleaners or solvents.
  • Battery Replacement: Replace batteries promptly when the low battery indicator appears on the display to ensure accurate measurements. Refer to section 4.1 for battery installation.
  • Storage: When not in use for extended periods, remove the batteries to prevent leakage. Store the device in its aluminum case in a cool, dry place, away from direct sunlight and extreme temperatures.
  • Environmental Conditions:
    • Working Temperature and Humidity: -10℃ to 40℃; less than 80%RH
    • Storage Temperature and Humidity: -20℃ to 60℃; less than 70%RH

7. Troubleshooting

Problem Possible Cause Solution
Device does not power on Dead or incorrectly installed batteries Replace batteries with new ones, ensuring correct polarity.
"OL" symbol displayed Overrange overflow (measurement exceeds device's maximum range) Ensure the measured value is within the specified range for your model (ST4100: 500Ω, ST4800: 1200Ω).
"NOISE" symbol displayed High interference signal detected Move away from sources of strong electromagnetic interference. Re-test in a clearer environment.
Flashing "MEM" symbol Data storage is full Review and clear unnecessary stored data to free up space.
Inaccurate readings Low battery, dirty clamp jaws, or external interference Replace batteries, clean clamp jaws, or re-test in a less noisy environment.

8. Specifications

Parameter Detail
Model ST4100 / ST4800 (Optional)
Brand Name KKMOON
Material ABS
DIY Supplies Electrical
Function Grounding resistance test, circuit resistance test, leakage current test
Environmental Temperature and Humidity 23℃ ± 5℃, lower than 75%RH
Power Supply DC 6V, 4 * 1.5V AA dry battery (not included)
Measurement Method Mutual feeling way
Resistance Range ST4100: 0.010Ω-500Ω
ST4800: 0.010Ω-1200Ω
Resistance Resolution 0.001Ω
Current Range 0.00mA-30.0A (ST4800 only)
Current Resolution 0.01mA
Clip Size Φ1.26" (32mm) / 55mm x 32mm
Time Clock Feature Yes
Ω + A Synchronous Display Yes, on the same screen
Display Type Digital Only, 4-bit LCD display, black screen design
LCD Size 46mm x 36mm
Measure Time 1 Time/second
Data Storage 500 groups, "MEM" indication
Data Access "MR" symbol indication when reviewing
Overflow Display "OL" symbol indication
Disturbed Test Automatic interference signal identification, "NOISE" symbol for high interference
Alarm Function Audible prompt when measured value exceeds set point
Cell Voltage Battery power displayed in real-time
Auto Shut Off Configurable (5, 10, 15, 20 minutes, OFF), default 5 minutes
Power Dissipation 115mA Max
Working Temperature and Humidity -10℃~40℃; lower than 80%RH
Storage Temperature and Humidity -20℃~60℃; lower than 70%RH
Insulation Resistance 20MΩ above (Between the circuit and the housing 500V)
Withstand Voltage AC 3700V/rms (Between the circuit and the housing)
External Magnetic Field <40A/m
External Electric Field <1V/m
Safety Regulation IEC61010-1(CAT III 300V, CAT IV 150V, degree of pollution 2); IEC61010-031; IEC61557-1 (earthing resistance)
Item Size 295 * 85 * 58mm / 11.61 * 3.35 * 2.28in
Item Weight 888g / 1.96lb
Package Weight 1970g / 4.34lb
Package Size 35 * 13 * 21cm / 13.78 * 5.12 * 8.27in
Diagram showing the dimensions of the clamp meter: 295mm length, 85mm width, and 58mm height.
Figure 8: Device Dimensions.
Comparison image showing the ST4100 model with a resistance range of 0.010Ω-500Ω and the ST4800 model with a resistance range of 0.010Ω-1200Ω.
Figure 9: Model Comparison (ST4100 vs ST4800).

9. User Tips

  • Model Specificity: The ST4800 model offers a wider resistance range (up to 1200Ω) and includes leakage current testing, which the ST4100 does not. Always verify your model's capabilities against the specifications table for specific functions like circuit earth leakage measurement.
  • Calibration: Use the included Measuring Ring (Calibration Loop) periodically to verify the accuracy of your clamp meter.
  • Environmental Awareness: Be mindful of your surroundings. High interference signals can affect readings, indicated by the "NOISE" symbol. Try to perform measurements in a clear electrical environment.
  • Battery Life: The real-time battery voltage display helps monitor power. Replace batteries proactively to avoid interruptions during critical measurements.

10. Warranty & Support

This product comes with a 1-year guarantee from the date of purchase. This warranty covers manufacturing defects and ensures the product meets merchantable quality and fitness for purpose as described.

For any issues, technical support, or warranty claims, please contact customer support through your point of purchase. When contacting support, please have your product model (ST4100 or ST4800) and purchase details ready.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.