Introduction
Friendly Tips:
Please carefully read this instruction manual and use the product correctly to familiarize yourself with its functions conveniently and quickly.
There might be small differences between the photos and the actual product. Please refer to the actual product for detailed information.
Packing List
The package includes the following items:
- Jump Starter with Air Compressor
- Smart Jumper Cables
- USB-C to USB-C Cable
- Cigarette Lighter Converter
- Valve Adapter (x3)
- Air Hose
- Type-C Cable
- Zipper Carry Case
- User Manual
Parts and Function Description
| Part Name | Function |
|---|---|
| 1. Display Screen | Shows battery level, operational status, and error messages. |
| 2. PUMP Button | Short press to activate the product and display "KPA". Long press to start inflation. |
| 3. BAR/PSI Button | Short press to switch inflation unit (BAR, PSI). |
| 4. + Button | Increases pressure value. |
| 5. - Button | Decreases pressure value. |
| 6. Light | LED flashlight. |
| 7. Hose Socket | Connection point for the air hose. |
| 8. Jump Start Port | Connection point for smart jumper cables. |
| 9. Power Button | Short press to turn on the device. |
| 10. Light Button | Long press to turn on light, short press to switch light mode (Strobe, SOS). |
| 11. DC Out Port | 12V-16.8V / 10A output. |
| 12. USB Out Port | 5V/3A, 9V/2A, 12V/1.5A (18W MAX) output for charging devices. |
| 13. TYPE-C In/Out Port | 5V/3A, 9V/3A, 12V/3A, 15V/3A, 20V/3A (60W MAX) input/output for charging the unit or other devices. |
Specifications
| Feature | Specification |
|---|---|
| Model | AP1 |
| Start Voltage | 12V |
| Peak Current | 4000A |
| Type-C In/Out | 5V-3A, 9V-3A, 12V-3A, 15V-3A, 20V-3A (60W MAX) |
| USB Out | 5V-3A, 9V-2A, 12V-1.5A (18W MAX) |
| DC Out | 12~16.8V-10A |
| Unit Display | KPA/BAR/PSI |
| Adjustable Pressure Range | 1-1000KPA / 0.1-10.0BAR / 1-150PSI |
| Conversion Rate | >90% |
| Battery Capacity | 18000-20000 mAh |
| External Testing Certification | MSDS, CE |
| Number Of Built-in Batteries | 2 |
| Hign-concerned Chemical | None |
| Origin | Mainland China |
Operation Guide
General Notes Before Use:
- It is recommended to use a 60W AC adapter to charge the product (the 60W AC adapter is not included in the package).
- When using the product for the first time, please ensure it is fully charged.
- It is recommended to charge the product every 3 months to prolong its life, even if the unit is not in use.
1. Recharge the Product
- Connect the product to a power source via the charging cable.
- Disconnect the power after it is fully charged.
2. Charge Other USB Devices
- Connect the product to your iPhone, smartphone, or other USB electronic devices via the charging cable.
- Press the power button to start charging. Disconnect when charging is not required.
3. LED Flashlight
Long press the light button for 3 seconds to turn on the white flashlight. Short press to switch between Strobe and SOS modes. Press again to turn it off.
4. Start Vehicles (Jump Start)
Before use, please note:
- This product is only suitable for 12V vehicles.
- Before starting your car, ensure the product has enough power.
- Insert the jumper cable plug into the jump starter. When the indicator light of the jumper cable is blue, it means the jumper cable is in standby status.
- Connect the clamp to the car battery. Connect the red clamp cable to the positive (+) terminal and the black clamp cable to the negative (-) terminal. Please avoid reverse connection.
- When the indicator light of the jumper cable is green, you can try to start your vehicle.
- After jump-starting the engine, remove the battery clamp from the car battery. Then remove the clamp plug from the jump starter.
5. Inflate Tires
- Connect the inflation hose firmly to the product and the tire air valve respectively.
- Short press the power button to activate the product. Then press the "PUMP" button; the screen will display KPA (default 250). Press the "BAR/PSI" button to switch the inflation unit (BAR, default 2.5; PSI, default 36). Use the "+" and "-" buttons to adjust the desired pressure value.
- After setting, press and hold the "PUMP" button for three seconds to start inflation and display real-time tire air values.
- The product will stop automatically after reaching the preset pressure value.
Tip: If you use the inflator for a long time, it is recommended to stop every 10 minutes to allow it to cool down.
Troubleshooting
Abnormal Indication of Jumper Cable
| Letter | Stands For | Solution |
|---|---|---|
| LC | Low Capacity | Please charge the jump starter. |
| RC | Reverse Connection | Please exchange positive and negative poles of the jumper cable. |
| HT | High Temperature | Please wait 5 minutes before starting the car. |
⚠ Forbid to use this clamp in an environment full of flammable gas.
Jumper Cable Indicator Instruction
| Status | Technical Parameter | Description | Solution |
|---|---|---|---|
| Standby indication | Blue light | Jumper cable connected to jump starter, then blue light on. | / |
| Automatic conduction status indicator (ready to jump start your car) | Green light | Jumper cable connected to the car battery after connecting the jump starter, then green light on. | / |
| Force start function | Start the car within 30s | If the above operations cannot start your car, use the forced start function. | Ensure correct connection of clamps before using force start function. Long press the force start button for 3 seconds until green light on. |
Jumper Cable Protection Instruction
| Protection | Technical Parameter | Description | Solution |
|---|---|---|---|
| Reverse connection protection | RC | Wrong connection between jumper cable and car's positive and negative poles. The RC red light stays on. | Keep the correct connection: positive pole (red) to positive pole, negative pole (black) to negative pole. |
| High temperature protection | YES | The HT red light stays on and a long alarm sounds; voltage output is cut off. | Automatically recovers when the temperature drops. |
| Start timeout protection | 40S±5S | Automatically enters standby state after more than 40 seconds and the LED blue light stays on. | You can use it again after disconnecting for a minute. |
| Input low capacity protection | 13.5V±0.5V | When power of EC5 port is lower than 13.5V, there is no output. The LC red light stays on and a long alarm sounds. | Please charge the jump starter. |
| Short circuit protection | YES | No response. | Use the positive and negative poles of the jumper cable to connect the positive and negative poles of the car's engine to try to start your car. |
Frequently Asked Questions (FAQ)
- Q1: What is the service temperature of this product and how to store it?
- A: The working temperature is 0°C-45°C. If the ambient temperature is higher than 45°C, the internal instructions of the lithium-ion battery will change. It can expand and is not safe, so do not store it in the car for a long time, especially in summer.
- Q2: How long can the storage capacity of the battery last?
- A: 4-6 months. However, we recommend charging it every 2-3 months to keep your jump starter healthy.
- Q3: What should I do if this product does not charge?
- A: Charge it with a 5V charger and a Type-C cable, and wait overnight. If it still doesn't work, please contact us.
- Q4: Can this starter start a 24V truck?
- A: The AP1 jump starter is only suitable for 12V batteries.
- Q5: What to do if the machine inflates slowly?
- A:
- Check whether the power is sufficient.
- Check whether the air inflation tube is leaking.
- Check whether the connection parts at both ends of the tube are tightened.
- Check whether the inflated objects are leaking.
- Q6: What should I do if the battery cannot be inflated?
- A:
- Check whether the power is sufficient.
- Check whether the current tire pressure is higher than the preset value.
- Q7: What to do if there is a leak in the connecting air hose?
- A: Tighten the connecting air hose.
- Q8: In other cases, what should I do if the machine operation does not respond?
- A: Restart the machine.
Safety Warnings
⚠ Important Safety Information:
- Never short circuit the jump starter by connecting the Red and Black clamps.
- Do not disassemble the jump starter.
- If you find swelling, leakage, or odor, please stop using the jump starter immediately.
- Please use this starter at normal temperature and keep it away from humid, hot fireplaces.
- Do not start the vehicle continuously; there should be at least 30 seconds to 1 minute between two starts.
- When the battery power is less than 10%, do not use the jump starter, otherwise the device will be damaged.
- Before first use, please charge it for 3 hours or more.
- If the positive clamp of the starting power was incorrectly connected to the negative poles of the car battery, the product comes with relevant protective measures to avoid personal injury and property damage.
Note:
- For the first use, please make sure to fully charge before use.
- In normal use, please confirm that the unit has at least 50% power before use.
Warranty and Support
Warranty Exception:
- The product has been incorrectly operated or damaged due to irresistible reasons (such as flood, fire, earthquake, lightning, etc.).
- The product has been repaired, disassembled, or modified by non-manufacturer or non-manufacturer authorized technicians.
- The problem is caused by the wrong charger not matching the product.
- Beyond the product warranty period (12 months).
For further assistance or to view the original user manual in PDF format, please refer to the official documentation provided by the seller. A PDF user manual is available here.
