BAOFENG UV-17 Pro Max GPS

Contents

Baofeng UV-17 Pro Max GPS Walkie Talkie User Manual

Model: UV-17 Pro Max GPS | Brand: BAOFENG

1. Introduction and Overview

Thank you for purchasing the Baofeng UV-17 Pro Max GPS Walkie Talkie. This dual-band, dual-display, dual-watch amateur radio provides secure, instant, and reliable communications. This manual will guide you through its features and operations to ensure maximum performance.

Key Features:

  • Six-Band Frequency Support:
    • FM: 65-108 MHz (Only RX)
    • AM: 108-136 MHz (Air frequency receiving)
    • VHF1: 136-174 MHz (TX/RX)
    • VHF2: 220-260 MHz (TX/RX)
    • Police Band: 350-390 MHz (Only RX)
    • UHF: 400-520 MHz (TX/RX)
  • Integrated GPS Positioning: View your current location in real-time, aiding navigation and team coordination.
  • Type-C USB Charging: Convenient charging via Type-C port, compatible with various power sources like car chargers, power banks, or laptops.
  • Wireless Copy Frequency (FQSCAN): Easily search and copy transmission frequencies and privacy codes from other radios.
  • 1.77-inch High-Definition LCD Screen: Clear display with frequency and channel modes, showing all function menus (VOX, FM, CT, etc.).
  • LED Flashlight: Powerful built-in flashlight for emergency situations or low-light conditions.
  • PC & Manual Programmable: Most settings can be programmed directly via the keypad or through computer software.
  • Up to 999 Memory Channels
  • Dual Watch, Dual Standby
  • Three Scan Modes: Time/Carrier/Search
  • VOX (Voice Operated Transmission)
  • Alarm Mode: Site/Code/Tone
  • Frequency Hopping
  • CTCSS/DCS Scan
  • Roger Beep
  • DTMF

2. Safety Warnings and Regulations

Please read and adhere to the following safety information to ensure safe operation and compliance with regulations.

FCC Regulatory Conformance:

This equipment complies with Part 15 of FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

RF Exposure Compliance and Control:

To control your exposure and ensure compliance with occupational/controlled environmental exposure limits, always adhere to these procedures:

  • Do not remove the RF Exposure Label from the device.
  • Transmit no more than 50% of the time. Press the Push-to-Talk (PTT) key to transmit; release to receive.
  • Keep the radio unit at least 2.5cm away from the face during transmission.
  • When worn on the body, always use an approved holder, holster, case, or body harness.
  • Use only approved antennas, batteries, and accessories to ensure compliance with FCC RF exposure guidelines.

Operating Prohibitions:

  • Do not operate in locations with fuels, chemicals, or explosive atmospheres.
  • Do not operate near blasting areas or medical/electronic equipment vulnerable to RF signals.
  • Do not hold the product while driving.
  • Do not operate where wireless communication is prohibited.

Important Tips:

  • Use only authorized accessories.
  • Keep the product at least 2.5 centimeters away from your body during transmission.
  • Avoid continuous high-volume reception for extended periods.
  • Do not place the product in airbag deployment areas in vehicles.
  • Keep out of reach of children and pets.
  • Operate within the specified temperature range.
  • Allow the product to cool if it accumulates heat from continuous transmission.
  • Handle with care; do not disassemble, modify, or repair without authorization.

Precautions for Batteries:

  • Do not charge or replace batteries in locations with fuels, chemicals, or explosive materials.
  • Do not charge wet batteries; dry them thoroughly first.
  • Do not charge deformed, leaking, or overheating batteries.
  • Do not charge with unauthorized chargers or in areas with strong radiation.
  • Avoid overcharging to prolong battery life.

Battery Maintenance Instructions:

  • Clean charging connector dust regularly with a dry cloth.
  • Charge batteries between 5℃~40℃ (40°F - 105°F).
  • Turn off the radio when charging a battery attached to the product.
  • Do not remove the battery or unplug the power cord during charging.
  • Do not dispose of batteries in fire or expose them to direct sunlight/heat sources.
  • Do not squeeze, penetrate, or remove the battery housing.

Transportation Instructions:

  • Damaged batteries must not be transported.
  • Separate batteries from metal parts or each other if transporting multiple in one package to avoid short circuits.
  • The radio must be switched off and secured against switch-on if the battery is attached.

3. Content of the Packaging

Your package should contain the following items:

  • 1 x Portable Radio
  • 1 x Soft Antenna
  • 1 x Li-ion Battery Pack
  • 1 x Desktop Charger
  • 1 x Belt Clip
  • 1 x The Sling
  • 1 x User's Manual (PDF reference: View User Manual PDF)

If any item is missing, please contact your dealer.

4. Radio Overview

4.1 Buttons and Controls of the Radio

Labeled diagram of Baofeng UV-17 Pro Max radio components
Diagram of the Baofeng UV-17 Pro Max with key components labeled.
  1. Antenna
  2. Flashlight/Emergency Alert Key
  3. PTT Key
  4. FM Broadcast/Monitor Key
  5. Menu Key
  6. Numeric Keypad
  7. Power/Volume Knob
  8. Color LCD
  9. Accessory Jack
  10. MIC Input
  11. Exit Key
  12. Navigation Keys (Up/Down)
  13. Battery Pack
  14. Battery Tightening Screw
  15. TX/RX Status LED
  16. LED Flashlight

4.2 LCD Display Icons

Baofeng UV-17 Pro Max displaying GPS location on a map
The 1.77-inch LCD screen displays GPS information and other operational data.
Icon Description
RSSISquelch Open/Close Indicator
H/LTransmit power level indicator (High/Low)
DDCS enabled
CCTCSS enabled
+TX shifted higher in frequency than RX (repeater access)
-TX shifted lower in frequency than RX (repeater access)
DDual watch enabled
.Keypad lock enabled
VOXVOX enabled
NNarrowband enabled
Battery iconBattery level indicator
RReverse function enabled
Arrow iconIndicates active band or channel

Battery Level Indicator: When the battery level indicator shows empty, the battery is depleted. The radio will beep, flash the backlight, and announce "Low Voltage" if voice prompts are enabled. Charge the battery immediately.

4.3 Status Indications (LED)

LED Indicator Radio Status
Constant RedTransmitting
Constant GreenReceiving

5. Setup and Installation

5.1 Charging the Battery Pack

The Li-ion battery pack is not charged at the factory. Please charge it fully before first use. For optimal performance, fully charge and discharge the battery two or three times initially. Use only the specified charger provided with the radio.

Close-up of Type-C fast charging port on the Baofeng UV-17 Pro Max
The Type-C port allows for convenient charging.
  1. Plug the AC adaptor into an outlet and connect it to the DC jack on the charger. The indicator light will blink orange.
  2. Place the battery or radio (with battery) into the charger. Ensure good contact with charging terminals. The indicator light will turn red, indicating charging has begun.
  3. A full charge takes approximately 2-5 hours. The indicator light turns green when charging is complete.
  4. If charging the radio while powered on, the indicator may not turn green. Turn off the radio for proper indication.
Baofeng UV-17 Pro Max showing battery compartment and charging contacts
Ensure proper battery installation and contact with charging terminals.

5.2 Installation of Accessories

Installing/Removing the Antenna:

  1. Installing: Screw the antenna clockwise into the connector on top of the transceiver until secure.
  2. Removing: Turn the antenna counterclockwise to remove it.

Installing the Belt Clip:

  1. Remove the two parallel screws above the battery on the back of the radio.
  2. Thread the screws through the holes on the belt clip and screw them back into the radio body.
  3. Removing: Unscrew counter-clockwise to remove the belt clip.

Installing the Battery Pack:

Ensure the radio is turned off before attaching or removing the battery.

  1. Align the battery parallel with the radio body, with the lower edge about 1-2cm below the radio's edge.
  2. Slide the battery upward along the guide rails until it clicks into place.
  3. Removing: Press the battery release above the battery pack while sliding the battery downward.

Installing Additional Speaker/Microphone (Optional):

Pry open the rubber MIC-Headset jack cover and insert the Speaker/Microphone plug into the double jack.

6. Basic Operations

6.1 Power On/Off the Radio

  • Power On: Rotate the Volume/Power knob clockwise until you hear a "click". The display will show a message or flash, then display a frequency or channel. If voice prompts are enabled, it will announce "frequency mode" or "channel mode".
  • Power Off: Rotate the Volume/Power knob counter-clockwise until you hear a "click".

6.2 Adjusting the Volume

  • Increase Volume: Turn the Volume/Power knob clockwise.
  • Decrease Volume: Turn the Volume/Power knob counter-clockwise.

6.3 Main Band/Sub Band Select

In standby mode, press the ▲ key to switch between A (upper) and B (lower) displays. The selected display's frequency or channel becomes active for listening and transmitting.

6.4 VFO/Channel Switch

Press and hold the MENU key to switch between VFO (Frequency) and Channel (MR) modes. In Channel mode, the channel number is displayed. In VFO mode, 'VFO' is displayed.

6.5 Frequency (VFO) Mode

In VFO mode, use the ▲ or ▼ keys to increment or decrement the frequency according to the set frequency step. Frequencies can also be entered directly using the numeric keypad.

WARNING: Programming a channel does not automatically authorize its use. Transmitting on unauthorized frequencies is illegal. Always consult local regulations.

6.6 Making a Call

Press the MENU key to switch the main channel if two channels are displayed.

  • Channel Mode Call: Select a channel, then hold down the [PTT] key to transmit. Speak into the microphone with a normal tone. The red LED will illuminate.
  • Frequency Mode Call: Switch to VFO mode, input the desired frequency, then hold down the [PTT] key to transmit. The red LED will illuminate.
  • Receive a Call: Release the [PTT] key to receive. The green LED will illuminate when receiving.

Note: For best reception, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.

6.7 Using the Flashlight

Baofeng UV-17 Pro Max flashlight in use in a dark, outdoor setting
The built-in LED flashlight provides illumination in dark environments.
  1. Press the Flashlight/Emergency Alert key once to turn on the LED flashlight continuously.
  2. Press it again to activate the strobe emergency signal.
  3. Press it a third time to turn off the light.

6.8 Emergency Alert

To activate, press and hold the Flashlight/Emergency Alert key for 3 seconds. The radio will emit a loud siren and the flashlight will flash. Press the key again to exit.

WARNING: The Emergency Alert feature should only be used in actual emergencies.

6.9 FM Radio (FM)

The radio can receive FM broadcasts from 65-108 MHz.

  1. Press the [SK2] key to turn on the radio.
  2. Select the desired frequency using the ▲ or ▼ keys, or input it directly. Press #z to automatically search for stations.
  3. Press the [SK2] key to exit FM radio.

6.10 Monitor

In standby, press and hold the [SK2] key to enter Monitor mode. This opens the squelch to listen to unfiltered signals. Release [SK2] to return to standby.

6.11 Keypad Lock

To enable/disable the keypad lock, press and hold the * key for about two seconds. The keypad can also be set to lock automatically after ten seconds via the menu.

6.12 Frequency Reversal

A short momentary press of the * key enables the reverse function, swapping your transmit and receive frequencies. An 'R' will appear on the LCD.

6.13 TX Repeaters Tone

Press [PTT] + Flashlight/Emergency Alert key to send a 1750Hz repeater tone. This is useful for accessing repeaters. This function works even if the keypad is locked.

Two Baofeng UV-17 Pro Max radios demonstrating fast copy frequency feature
The wireless copy frequency feature allows quick duplication of settings.
  1. Press and hold the MENU key. The screen will display "SEARCH SEARCH...".
  2. The radio will act as a receiver. If a strong, stable signal is received, its frequency and CTCSS/DCS value (if present) will be displayed.
  3. Press the MENU key to save the found frequency and CTCSS/DCS to a channel.
  4. During search, press #z to switch between UHF or VHF bands.

6.15 Weather Radio/Scan Weather Channel (NOAA)

The radio features NOAA Weather Radio functionality to receive weather reports.

  1. To turn on NOAA Weather Scan, press and hold the [0sQL] key for 3 seconds. The radio will enter Weather band mode.
  2. Press and hold the #z key for 3 seconds to start automatic scanning of all 10 NOAA channels. Press again to stop.
  3. After stopping the scan, you can manually select a weather channel using the ▲ or ▼ keys.
  4. To exit Weather Radio broadcast mode, press the EXIT key or [PTT] key.

Note: NOAA Weather Channels Wx 1 Thru 10 are Receive-only channels. You cannot transmit on these channels.

7. Advanced Features

7.1 Working the Menu System

The radio's menu system allows customization of various settings. If the radio is in Memory (MR) mode, some menu items (STEP, TXP, W/N, CTCSS, DCS, S-CODE, PTT-ID, BCL, SFT-D, OFFSET, MEM-CH) will not take effect.

Basic Menu Use:

  1. Press the MENU key to enter the menu.
  2. Use the ▲ / ▼ keys to navigate between items.
  3. Press MENU again to select an item.
  4. Use ▲ / ▼ keys to select the parameter.
  5. Press MENU to confirm and save, or EXIT to cancel.
  6. Press EXIT to exit the menu at any time.

Using Menu Short-cuts:

Each menu item has a numerical value for direct access.

  1. Press the MENU key.
  2. Use the numerical keypad to enter the menu item number.
  3. Press the MENU key to enter the item.

7.2 Scanning

The radio has a built-in scanner for VHF and UHF bands. In VFO mode, it scans according to the set frequency step. In Channel (MR) mode, it scans your programmed channels.

To enable/disable the scanner, press and hold the #z key for about two seconds.

Scanning Modes:

  • Time Operation (TO): Scanner stops on a signal, then resumes after a fixed time.
  • Carrier Operation (CO): Scanner stops on a signal, then resumes after the signal disappears.
  • Search Operation (SE): Scanner stops on a signal and remains stopped.

To set the scanner mode: MENU -> 21 (SC-REV) -> Select mode -> MENU to confirm -> EXIT.

Frequency Scanning:

In frequency mode, press #z for >2 seconds to start. Change direction with ▲ / ▼. Press #z to stop.

Channel Scanning:

In channel mode, press #z for >2 seconds to start. Change direction with ▲ / ▼. Press #z to stop.

Scan CTCSS/DCS:

In standby, press MENU -> 14 (Scan CTCSS) or 15 (Scan DCS) -> MENU to start. This function only works when a signal is detected.

7.3 Manual Programming (Channels Memory)

The radio has 999 memory channels. Each channel can store receive/transmit frequencies, power, signaling, bandwidth, and a six-character alphanumeric identifier.

Programming a Channel Repeater Offset with CTCSS Tone (Example):

To program a new memory in Channel 10 with RX = 432.55000 MHz, TX = 437.55000 MHz (+5 Offset), and TX CTCSS tone 123.0:

  1. Press MENU to switch between menus.
  2. Press and hold MENU to set the radio to VFO mode.
  3. Enter [3][1] [1][0] to delete prior data in channel 10.
  4. Enter [1][2] 123.0 to select desired TX encode tone.
  5. Enter RX frequency (e.g., 43255000).
  6. Press MENU [3][0] [1][0] to enter the desired channel (10). RX has been added.
  7. Enter TX frequency (e.g., 43755000).
  8. Press MENU [3][0] [1][0] to enter the same channel (10). TX has been added.
  9. Press and hold MENU to return to MR mode.

7.4 Repeaters Programming

This section assumes you know your repeater's transmit and receive frequencies and are authorized to use them.

  1. Press and hold MENU to set the radio to VFO mode.
  2. Enter the repeater's output (your receiving) frequency using the numeric keypad.
  3. Press MENU.
  4. Enter 29 (OFFSET) on the numeric keypad.
  5. Press MENU.
  6. Use the numerical keypad to enter the specified frequency offset.
  7. Press MENU to confirm and save.
  8. Enter 28 (SFT-D) on the numeric keypad to get to offset direction.
  9. Use the ▲ / ▼ keys to select + (positive) or - (negative) offset.
  10. Press MENU to confirm and save.
  11. (Optional) Save to memory and set up CTCSS.
  12. Press EXIT to exit the menu.

7.5 VOX (Voice Operated Transmit)

This function enables hands-free conversations. Speak into the microphone to activate transmission.

In standby mode, press MENU -> 7 (VOX). Press MENU to enter, use ▲ / ▼ to select VOX level (1-10) or turn OFF, then MENU to confirm. Press EXIT to return to standby.

Note: Level 1 is least sensitive, level 9 is most sensitive. VOX is not enabled in Scan or FM Radio mode.

7.6 Dual Watch

Allows monitoring two channels simultaneously by flipping between them at fixed intervals.

To enable/disable: Press MENU -> 7 (TDR) -> Select ON/OFF -> MENU to confirm -> EXIT.

7.7 Stopwatch Timer

In standby mode, press MENU -> 44 (STOP WATCH). The screen displays "STOP WATCH". Press MENU to start/restart timing. To exit, stop the timer first, then press EXIT.

7.8 DTMF (Dual-Tone Multi-Frequency)

DTMF is used for signaling in two-way radio systems, often for automation or remote control (e.g., activating repeaters).

1209Hz 1336Hz 1477Hz 1633Hz
697Hz123A
770Hz456B
852Hz789C
941Hz*0#D

To send DTMF codes, press the corresponding key(s) while holding down the PTT key. This works even with keypad lock enabled.

7.9 Customization

The radio offers various customization options for visual and audible features.

  • Display Backlight (ABR) - Menu 7: Set backlight duration (ON/5/10/15/20 seconds).
  • Beep PROMPT (BEEP) - Menu 8: Enable/disable key press beep tone.
  • Voice Function (VOICE) - Menu 17: Enable/disable voice prompts.
  • Language of the MENU (LANGUAGE) - Menu 18: Set menu language (English/Chinese).
  • Working Mode (MDF-A) - Menu 24: Select display mode (Channel Number, Channel Name, Programmed Frequency).
  • Roger Beep (ROGER) - Menu 36: Enable/disable end-of-transmission tone.
  • Power On Message (POWER ON MSG) - Menu 40: Customize welcome message (VOLTAGE, MESSAGE, LOGO, MODEL NAME).
  • Power On Password (POWER ON PWD) - Menu 43: Set a password required to turn on the radio.

7.10 Reset - Menu 42

Two reset modes are available:

  • Reset VFO: Resets all settings except channels to default.
  • Reset ALL: Resets all settings, including channels, to default.

To perform a reset: Press MENU -> 42 (RESET) -> Select VFO or ALL -> MENU to confirm. The radio will reboot.

8. Troubleshooting Guide

Phenomena Analysis Solution
Cannot turn on the radioBattery installed improperly, battery run out, dirty/damaged battery contactsRemove/reattach battery, recharge/replace battery, clean battery contacts
Weak or intermittent voice during receptionLow battery voltage, low volume, loose antenna, blocked speakerRecharge battery, increase volume, reattach antenna, clean speaker
Cannot communicate with other group membersInconsistent frequency/signaling, too far from othersVerify TX/RX frequency/signaling, move closer to others
Unknown voices or noiseInterrupted by other radios, analog mode without signalingChange frequency, adjust squelch, set signaling for current channel
Unable to hear anyone due to too much noise/hissToo far from others, unfavorable position (blocked), external disturbanceMove to open area, restart radio, stay away from interference
Radio keeps transmittingVOX turned on or headset not installedTurn off VOX, check headset installation

Note: If these solutions do not resolve your issues, please contact your dealer for technical support.

9. Specifications

Category Specification
Frequency Range (TX)144-148MHz, 420-450MHz
Frequency Range (RX)136-174MHz, 400-519.995MHz
Frequency Range (FM)65-108MHz
Output Power5W/2W
Channel Spacing25.0KHz (Wide) / 12.5KHz (Narrow)
Memory Channel999 Groups
Operation VoltageDC 7.4V ±10%
Transmission Current≤1700mA
Receive Sensitivity0.25μV (12dB SINAD)
Rated Audio Power Output1W @ 16 ohms
Receive Current≤380mA
Connection for accessories2 pin Kenwood jack
Antenna Impedance50 Ohm

Note: All specifications may be modified without prior notice or liability.

10. User Tips

No specific user tips were available from the provided reviews or Q&A content.

11. Warranty and Support

Disclaimer:

The accuracy and completeness of the contents are sought in the process of compilation, but we do not bear any responsibility for possible errors or omissions. With the continuous development of technology, we reserve the right to change the design and specification of the product without notice. No copy, modification, translation and dissemination of this handbook may be made in any form without the prior written authorization of our department.

For further support or inquiries, please refer to the official user manual PDF: Baofeng UV-17R Series User Manual.

Contact information for PO FUNG ELECTRONIC (HK) INTERNATIONAL GROUP COMPANY LIMITED:

ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong
Website: www.baofengradio.com | www.pofungshop.com
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.