1. Introduction
The EARU EAPDX-63AVE-RGB is a versatile 3-in-1 protective device designed to safeguard electrical circuits from over-voltage, under-voltage, and over-current conditions. It features an adjustable digital display that shows real-time voltage, current, and energy consumption. This device automatically disconnects the circuit when parameters exceed set limits and automatically recovers once conditions return to normal, ensuring reliable protection for your electrical appliances and systems.

Figure 1: Front view of the Multi-Function Protector displaying key protection features.
2. Key Features
- Adjustable Protection: User-configurable settings for over-voltage, under-voltage, and over-current thresholds.
- Real-time Display: High-definition digital display shows voltage (V), current (A), and energy (KWh) simultaneously.
- Automatic Recovery: Automatically reconnects the circuit after a set delay once fault conditions are cleared.
- Delay on Time: Adjustable reconnect time from 1 to 600 seconds.
- Calibration Function: Allows for voltage and current calibration.
- Energy Meter Reset: Option to reset the accumulated energy consumption.
- Flame-Retardant Material: Constructed from high heat-resistant, insulating, and flame-retardant PC material for safety.
- Din Rail Mounting: Easy installation on a 35MM Din Rail with securing clips.

Figure 2: Visual representation of the protector's main features.
3. Specifications

Figure 3: Product dimensions and technical parameters.
| Parameter | Value |
|---|---|
| Poles | 1P+N |
| Rated Current | 1-63A (Adjustable) |
| Rated Voltage | AC230V |
| Rated Frequency | 50/60Hz |
| Operating Voltage Range | AC 80V-400V (Single Phase) |
| Over-Voltage Protection (U>) | 230V-300V (Adjustable, Default: 280V) |
| Under-Voltage Protection (U<) | 80V-210V (Adjustable, Default: 160V) |
| Over-Current Protection (I>) | 1A-63A (Adjustable, Default: 50A) |
| Reconnect Time (Delay on Time) | 1-600s (Adjustable, Default: 5s) |
| Rated Insulation Voltage | 400V |
| Measurement Accuracy | ±1% |
| Installation | 35MM Din Rail |
| Operating Temperature | -50-55℃ |
| Humidity | <50% at 40℃ (Without Condensation) |
| Protection Class | IP20 |
| Certification | CE |
4. Package Contents
The package typically includes:
- 1 x EARU EAPDX-63AVE-RGB Multi-Function Protector
- 1 x User Manual (this document)
5. Safety Information
- Installation and maintenance should only be performed by qualified electricians.
- Ensure power is disconnected before any installation or wiring work.
- Do not operate the device in wet or damp conditions.
- Verify all connections are secure and correct to prevent electrical hazards.
- The device is designed for indoor use in a clean, dry environment.
6. Installation
The EARU EAPDX-63AVE-RGB is designed for 35MM Din Rail mounting. Follow these steps for proper installation:
- Power Off: Ensure the main power supply to the circuit is completely disconnected before starting installation.
- Mounting: Clip the protector onto a standard 35MM Din Rail in your electrical distribution box.
- Wiring: Connect the input (IN) and output (OUT) wires as shown in the wiring diagram below. The device uses single-channel wiring with tunnel-type wiring ports for secure connections.
- Connect the Neutral (N) wire to the 'N' terminal on both IN and OUT.
- Connect the Live (L) wire to the 'L' terminal on both IN and OUT.
- Secure Connections: Tighten all terminal screws firmly to ensure good electrical contact and prevent loose connections.
- Power On: Once all wiring is complete and checked, restore power to the circuit.

Figure 4: Wiring Installation Diagram and button functions.

Figure 5: Settings Menu overview and wiring diagram.
7. Operation
7.1 Display Overview
Upon powering on, the device's digital display will show the current voltage (V), current (A), and accumulated energy consumption (KWh).
7.2 Setting Parameters
To enter the setting menu, press and hold the 'SET' button for more than 3 seconds. Use the 'Up' and 'Down' arrow buttons to navigate through the settings and adjust values. Press 'SET' again to confirm a selection or move to the next parameter.
The settings menu includes parameters such as:
- Power-on delay time (Pt): 1s-600s
- Protection recovery delay (rt): 1s-600s
- Over-voltage protection setting (U>): 230V-300V
- Over-voltage recovery setting (U>r): 225V-295V
- Under-voltage protection setting (U<): 80V-210V
- Under-voltage recovery setting (U<r): 85V-215V
- Over-under-voltage protection action delay time (UUE): 0.1s-10s
- Calibration Voltage Value (URd): -9.9V - 9.9V
- Over current protection value (I>): 1-63A
- Overcurrent protection action time (I>t): 0.1s-60s
- Overcurrent continuous times (I>c): 0-20
- Current Calibration (CRd): -9.9A - 9.9A
- Power range setting (PC): 1-999
- Reset mode (CLP): CLP 000 (Reset setting), CLP 003 (Reset power level), CLP 009 (Restore Factory Settings)
Video 1: Demonstration of navigating the settings menu and adjusting parameters.
8. Maintenance
- Keep the device clean and free from dust. Use a dry, soft cloth for cleaning.
- Do not use abrasive cleaners or solvents.
- Regularly check wiring connections for tightness and signs of wear or damage.
- Ensure proper ventilation around the device to prevent overheating.
9. Troubleshooting
- Device not powering on: Check input power supply and wiring connections. Ensure the voltage is within the operating range (AC 80V-400V).
- Device trips frequently: Review your over-voltage, under-voltage, and over-current settings. They might be set too sensitively for your load or power conditions. Adjust the protection values or recovery delays as needed.
- Incorrect voltage/current readings: Consider performing a voltage or current calibration using the 'URd' or 'CRd' settings in the menu.
- Device does not reconnect: Check the 'Protection recovery delay' (rt) setting. Ensure it's not set to an excessively long time. Also, verify that the fault condition (over/under voltage, over current) has cleared.
10. User Tips
- Wiring Clarification: When connecting, ensure that the Neutral (N) and Live (L) wires are correctly identified and connected to their respective 'IN' and 'OUT' terminals. Incorrect wiring can lead to malfunction or damage.
- Resetting Energy Meter: To reset the accumulated energy (KWh) counter, navigate to the settings menu and select 'CLP 003' (Reset power level). Confirm the selection to clear the energy data.
- Factory Reset: If you encounter persistent issues or wish to revert all settings to their default values, use the 'CLP 009' option in the settings menu to restore factory settings.
11. Warranty and Support
For warranty claims, technical support, or service inquiries, please contact your original point of purchase or the manufacturer directly. Keep your purchase receipt as proof of purchase.