1. Introduction and Overview
The FDIK 5KW Aluminum Shell Diesel Air Parking Heater is an independent on-board heating device designed to provide warmth without starting the vehicle's engine. It features its own fuel pipeline, circuit, combustion, and control systems. This heater is ideal for pre-heating and maintaining warmth in various environments during cold weather, including cars, RVs, yachts, boats, trailers, cabins, and warehouses.
The heater boasts a durable aluminum shell, measuring 400 x 140 x 140 mm, and weighs approximately 6.4 kg (including packaging). Its robust construction ensures efficient heating and longevity. Key features include universal voltage compatibility, overheating protection, and intelligent temperature control.



2. Safety Information
Please read and understand all safety warnings and instructions before installing and operating this heater. Failure to follow these instructions may result in fire, explosion, electric shock, or other injuries.
- Exhaust Gas: Exhaust gas contains poisonous gas (carbon monoxide). During operation, the exhaust port must be mounted outdoors to prevent carbon monoxide poisoning.
- Muffler Installation: The muffler must be mounted horizontally according to the diagram, with the small drain hole facing downwards to prevent water accumulation.
- Ventilation: Ensure adequate ventilation around the heater. The air inlet and air outlet must be reserved for ventilation and should not be obstructed.
- Overheating Protection: The heater is equipped with an overheating protection device. Do not tamper with or bypass this safety feature.
- Fuel: Use only Diesel fuel. Operating the heater with other fuels may cause damage or create a fire hazard.
- Electrical Connections: All electrical connections must be secure and correctly wired. The positive and negative main wires must be connected directly to the battery to ensure normal operation.
- Certification: This product is CE certified, indicating compliance with European safety standards.
3. Package Contents
Upon receiving your FDIK Diesel Air Parking Heater, please verify that all the following components are included in the package:

- FDIK 5KW Heater Unit
- LCD Switch (Control Panel)
- Remote Control
- Silencer
- Oil Pump
- Oil Filter
- 8.8L Fuel Tank
- 75mm Wind Head
- Air Filter
- Rubber Pad
- Fixed Plate
- Tubing (various)
- Oil Pump Clamp
- Wiring Harness
- Exhaust Pipe
- Screw Accessory Kit (various screws, clamps, washers)
4. Installation
Proper installation is crucial for the safe and efficient operation of your FDIK Diesel Air Parking Heater. Refer to the diagrams and instructions below carefully.
4.1 Wiring and Fuel Line Diagram

- The positive (+) and negative (-) main wires must be connected directly to the battery to ensure normal operation of the main unit.
- The oil pump is preferred to be installed at an angle between 15° and 35° for optimal performance.
- Ensure the air inlet and air outlet are clear and unobstructed for proper ventilation and cooling.
4.2 Recommended Installation Positions
The heater can be installed in various locations depending on the vehicle type. Consider the following recommendations:

- TRUNK: Can be installed on the co-driver's legroom, on the back wall of the cab, behind the driver's seat backrest, or within the tool box.
- RV: Suitable for installation in front of the passenger seat, between the driver and passenger seats, under a container, or in the trunk.
- 5 Seater / 7 Seater Vehicles: Primarily installed in the passenger room or luggage compartment. If internal installation is not feasible, fix the heater underneath the vehicle, taking precautions against splashing.
- Excavator: Install inside the driver's seat, on the back wall of the cab, or inside the protection box.
5. Operating Instructions
Your FDIK Diesel Air Parking Heater offers flexible control options for optimal comfort.
5.1 Control Options
- LCD Control Panel: The heater can be controlled directly via the integrated LCD switch.
- Remote Control: For convenience, a remote control is included to manage the heater's functions from a distance.
- Bluetooth App: The heater is equipped with a built-in Bluetooth chip, allowing control via a dedicated mobile application on your smartphone (Android/iOS). Please refer to the product packaging or contact FDIK customer support for the specific app name and download instructions.
5.2 Heating Modes and Temperature Control
The FDIK heater provides two heating modes: Power Mode and Temperature Mode.
- Power Mode: You can adjust the heating power from H1 (lowest) to H5 (highest).
- Temperature Mode: The heater features an accurate temperature sensor, allowing you to set the desired temperature up to 40°C.
- Switching Modes: To switch between Power Mode and Temperature Mode, press and hold the 'set' button on the upper left corner of the LCD control panel.
5.3 Timer Function
The 2021 FDIK heater models include a timing function. This allows you to set specific times for the heater to automatically start or turn off, according to your schedule and preferences. This function can be configured via the LCD control panel or the mobile application.


6. Specifications
Detailed technical specifications for the FDIK 5KW Aluminum Shell Diesel Air Parking Heater:
| Feature | Specification |
|---|---|
| Brand Name | FDIK |
| Model Name | FDIK Aluminum (F23 Pro) |
| Item Type | Heating & Fans |
| Material | Aluminum |
| Fuel | Diesel |
| Power (W) | 5000W (Output) / 40W (Input) |
| Voltage | 12V / 24V (DC12V) |
| Thermal Power Range | 1000-5000W |
| Operating Temperature | -40°C to 40°C |
| Air Volume | 60-180 m³/h |
| Item Length | 40cm |
| Item Width | 14cm |
| Item Height | 14cm |
| Item Diameter | 7.5cm |
| Item Weight | 6.5kg (approx. total weight with packaging) |
| Switch Type | Rotary switch |
| Special Features | Heating, Bluetooth Function, Clock Mode, Overheating Protection |
| External Testing Certification | CE |
| Origin | Mainland China |


6.1 Performance Data

| Heater Model | 5000W | ||||
|---|---|---|---|---|---|
| Heating medium | Air | ||||
| Calorific grade | Super high grade | Top grade | Medium grade | Low grade | Closed |
| Value (W) | 5000 | 3500 | 2000 | 900 | - |
| Medium flux (kg/h) | 185 | 150 | 110 | 60 | 24 |
| Fuel Consumption (liter/hours) | 0.64 | 0.4 | 0.28 | 0.11 | - |
| Power consumption (W) | 40 | 24 | 13 | 7 | 7 |
| Lower limit of undervoltage | 10.5V/21V | ||||
| Overvoltage limit of undervoltage | 16V/32V | ||||
7. Maintenance
Regular maintenance ensures the longevity and optimal performance of your FDIK Diesel Air Parking Heater.
- Keep Clean: Periodically clean the exterior of the heater and ensure all air vents are free from dust and debris.
- Check Connections: Regularly inspect all electrical and fuel line connections for tightness and signs of wear or damage.
- Ventilation: Always ensure that the air inlet and air outlet are clear and unobstructed. Proper airflow is essential for efficient operation and to prevent overheating.
- Fuel Quality: Use high-quality Diesel fuel to prevent blockages and ensure efficient combustion.
- Fuel Filter: Check and replace the fuel filter as needed to maintain clean fuel supply to the pump.
- Exhaust System: Inspect the exhaust pipe and silencer for any blockages or damage. Ensure the muffler's drain hole is clear.
8. Troubleshooting
If you encounter issues with your FDIK Diesel Air Parking Heater, refer to the following table for common fault codes and their solutions.


| Fault Code | Cause | Workaround |
|---|---|---|
| E-2 | Supply voltage range | Normal range: 24V (18-32V), 12V (9-16V). Check whether the battery or generator is normal and whether the fuse is aging. |
| E-3 | Glow plug failure | Check whether the ignition plug connector is loose or the wire is short-circuited to the housing. Check whether the ignition plug is damaged. |
| E-4 | Oil pump failure | Check whether the oil pump connecting wires and connectors are damaged, loose, oxidized, short-circuited, or open-circuited. |
| E-5 | High temperature alarm (intake air>50°C; housing>230°C) | Check whether the heating air duct is unobstructed. Check whether the fan is operating normally. Check whether the temperature sensor is normal. |
| E-6 | Fan failure | Check if the impeller is stuck. Check whether the connection plug is loose. Is the gap between the magnet on the wind wheel and the Hall sensor on the controller too large? Is the circuit short-circuited or open-circuited? Is the motor leaking electricity? |
| E-7 | Connection failed | Detection harness. |
| E-8 | Lack of oil | Check whether there is oil shortage, oil solidification at low temperature, oil line blockage, oil pump stuck, etc. Check whether the oxygen inlet and exhaust pipes are unobstructed. Check whether the shell temperature sensor is in full contact with the shell and whether the pressure spring is firm. |
| E-9 | Sensor failure | Check whether the temperature sensor connection line or connector is damaged or loose, and whether the sensor is damaged. |
| E-10 | Startup failure | The casing temperature is too high and the casing cannot cool down after 3 minutes of startup. A lot of white smoke comes out of the exhaust gas. There is a small amount of white smoke or no smoke in the exhaust gas. a.Check whether the ignition plug is damaged. b.Is the gap between the inner wind wheels too large? |
9. User Tips
- Mobile App: For Bluetooth control, a specific mobile application is required. Please check the product packaging or contact FDIK customer support for the correct app name and download instructions for Android or iOS devices.
- Fuel Type: This heater is designed exclusively for Diesel fuel. Do not attempt to operate it with gasoline or any other fuel type, as this can cause severe damage to the unit and pose significant safety risks.
- Timer Setup: Utilize the built-in timer function to pre-heat your space before arrival or to automatically shut off the heater. This can be configured via the LCD control panel or the mobile app.
- Installation Location: When installing in a 5 or 7-seater vehicle, if internal space is limited, consider mounting the heater underneath the vehicle. Ensure it is protected from splashing water and road debris.
10. Warranty and Support
FDIK is committed to providing high-quality products and excellent customer service.
- Warranty: The product comes with a one-year warranty. Please note that vulnerable parts are not included in this warranty.
- After-Sales Service: FDIK offers 365 days of free after-sales service. In case of a heater malfunction, necessary replacement parts will be provided free of charge.
- Customer Support: For any inquiries or assistance, you can contact FDIK Customer Service Online via WhatsApp at +86 18636417766.


11. Frequently Asked Questions (FAQ)
- Q: What Android/iOS app is used for Bluetooth control?
- A: The manual states an app needs to be downloaded for Bluetooth control. Please refer to the product packaging or contact FDIK customer support for the specific app name and download instructions.
- Q: Can this heater run on gasoline?
- A: No, this heater is designed to operate exclusively on Diesel fuel. Using other fuels may cause damage or safety hazards.
- Q: How do I set the timer for automatic on/off?
- A: The FDIK aluminum shell heater features a built-in timer. You can set the desired start and stop times independently through the LCD control panel or the dedicated mobile application (if connected via Bluetooth). Refer to the "Operating Instructions" section for detailed steps.
- Q: My heater is not turning on. What should I do?
- A: Please refer to the "Troubleshooting" section of this manual, specifically the "Startup failure (E-10)" and "Supply voltage range (E-2)" entries. Ensure all connections are secure, the battery/generator is functioning correctly, and there is sufficient fuel. If the issue persists, contact customer support.
- Q: What certifications does this heater have?
- A: The heater has CE certification, indicating compliance with European safety standards. You can find the certification details in the product documentation.