1. Introduction
Thank you for purchasing the Baofeng UV-K61 Multi-Band Handheld Transceiver. This easy-to-use radio is designed to provide secure, instant, and reliable communications. Please read this manual carefully to ensure maximum performance and safe operation of your device.
This manual provides detailed instructions for setup, operation, maintenance, and troubleshooting. For additional information, you may refer to the official user manual PDF: Baofeng UV-K61 Owner's Manual (PDF).
1.1 Regulations and Safety Warnings
EU Regulatory Conformance: As certified by the qualified laboratory, the product complies with the essential requirements and other relevant provisions of Directive 2014/53/EU. All applicable EU regulations are regarded (2006/66/EC, 2011/65/EU, (EU)2015/863, 2012/19/EU). Note: It can be operated under 2000m.
WARNING! European Users should note that operation of this unit in Transmit mode requires the operator to have a valid Amateur Radio License from their respective Countries Amateur Radio Licensing Authority for the Frequencies and Transmitter Power levels that this Radio transmits on. Failure to comply may be unlawful and liable for prosecution. Refer to the “EU” specification guide 2014/53/EU. This information is applicable to EU countries only.
Compliance with RF Exposure Standards: The radio complies with the following RF energy exposure standards and guidelines:
- United States Federal Communications Commission, Code of Federal Regulations; 47 CFR § 1.1307, 1.1310 and 2.1093
- American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005; Canada RSS102 Issue 5 March 2015
- Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition
RF Exposure Compliance and Control Guidelines and Operating Instructions: To control your exposure and ensure compliance with occupational/controlled environmental exposure limits, always adhere to the following procedures.
Guidelines:
- Do not remove the RF Exposure Label from the device.
- User awareness instructions should accompany device when transferred to other users.
- Do not use this device if the operational requirements described herein are not met.
Operating Instructions:
- Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), press the Push-to-Talk (PTT) key. To receive calls, release the [PTT] key. Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy only when transmitting (in terms of measuring for standards compliance).
- Keep the radio unit at least 2.5cm away from the face. Keeping the radio at the proper distance is important as RF exposure decreases with distance from the antenna. The antenna should be kept away from the face and eyes.
- When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product. Use of non-approved accessories may result in exposure levels which exceed the FCC's occupational/controlled environmental RF exposure limits.
- Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure guidelines.
- Contact your local dealer for the product's optional accessories.
Precautions for Portable Terminals: To protect you against any property loss, bodily injury or even death, be sure to observe the following safety instructions:
- Do not operate the product in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials. In such location, only an approved Ex-protection model is allowed for use, but any attempt to assemble or disassemble it is strictly prohibited.
- Do not operate the product near or in any blasting area.
- Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate the product in any area where use of wireless communication equipment is completely prohibited.
Important Tips: To help you make better use of the product, be sure to observe the following instructions:
- Do not use any unauthorized or damaged accessory.
- Keep the product at least 2.5 centimeters away from your body during transmission.
- Do not keep the product receiving at high volume for a long time.
- For vehicles with an air bag, do not place the product in the area over the air bag or in the air bag deployment area.
- Keep the product and its accessories out of reach of children and pets.
- Please operate the product within the specified temperature range.
- Continuous transmission for a long time may lead to heat accumulation within the product. In this case, please keep it at a proper location for cooling.
- Handle the product with care.
- Do not disassemble, modify or repair the product and its accessories without authorization.
2. Getting Started
2.1 Content of the Packaging
Please verify that all items are present in your package. If any item is missing, please contact your dealer.
- 1 x Radio
- 1 x Fast desktop charger
- 1 x Antenna
- 1 x Li-Ion battery pack
- 1 x Wall adaptor
- 1 x Belt clip
- 1 x Type-C USB Cable
- 1 x User Manual (this document)

3. Product Overview
3.1 Buttons and Controls of the Radio

| No. | Component | Description |
|---|---|---|
| 1 | Antenna | Receives and transmits radio signals. |
| 2 | PTT Key | Push to Talk button for transmitting. |
| 3 | Flashlight / Alarm Switch | Activates the LED flashlight or emergency alarm. |
| 4 | Power / Volume knob | Turns the radio on/off and adjusts volume. |
| 5 | Battery release latch | Releases the battery pack. |
| 6 | SWEEP Key | Used for frequency sweep mode. |
| 7 | MENU Key | Accesses and confirms menu selections. |
| 8 | Color LCD | Displays frequency, channel, status icons, etc. |
| 9 | Accessory Jack | For connecting external speaker/microphone. |
| 10 | V/M-VFO/MR Mode Key | Switches between VFO (Frequency) and MR (Channel) modes. |
| 11 | Speaker | Outputs audio. |
| 12 | EXIT Key | Exits menus or functions. |
| 13 | Type-C charging indicator | Indicates charging status for Type-C port. |
| 14 | Type-C charging port | Connects Type-C charger. |
| 15 | LED flashlight | Provides illumination. |
| 16 | Status LED | Indicates radio status (transmitting/receiving). |
| 17 | Microphone | Picks up voice for transmission. |
| 18 | Keypad | Numeric and function keys for input. |
3.2 LCD Display Icons
| Icon | Description | Icon | Description |
|---|---|---|---|
| Mxxx | Memory channel | DW | Dual watch enabled |
| VFO | Frequency Mode | TX | Transmitting |
| VOX | VOX enabled | RX | Receiving |
| CTC | CTCSS enabled | R | Reverse function enabled |
| DCS | DCS enabled | ► | Indicates active band or channel |
| N | Narrowband enabled | +/- | Frequency shift direction if enabled in VFO |
| H/L | Transmit power level indicator (High/Low) | Battery level indicator | Squelch Open/Close Indicator |
3.3 Status Indications
The status LED has a very simple and traditional design. When you receive a signal it turns green, when you transmit it turns red, and it's off in standby.
| LED Indicator | Radio Status |
|---|---|
| Constant Red | Transmitting |
| Constant Green | Receiving |
3.4 Main Keypad Controls
- V/M: Short press to switch frequency or channel mode. Press and hold to toggle channel display mode: CH/FREQ/NAME.
- A/B: Short press to toggle upper screen (A)/lower screen (B). Press and hold to switch Double Wait/Signal Wait/Dual Watch off modes.
- 8 (One-Touch search key): Short press to enter One-Touch search key.
- EXIT: Short press to return to menu or return to previous menu. (Press and hold to enter frequency sweep mode).
- *: Long press to lock or unlock the keypad.
- #Z: Short press to enter DTMF dial. Press and hold to scan on and scan off.
- 0 (space): Press and hold to enter weather switch to select weather channel.
3.5 Programmed Key Functions
The [SK1] and [SK2] keys can be programmed for different functions. Access Menu 48/49/50 (PF1 Press/PF1 LongPre/PF2 Press) to configure.
| Function | Description |
|---|---|
| None | No function assigned. |
| Torch On/Off | Quickly switch the torch on or off. |
| Power Select | Quickly switch between high and low transmit power. |
| Scan On/Off | Quickly switch scanning function on or off. |
| VOX On/Off | Quickly switch VOX function on or off. |
| Alarm on/off | Quickly establishes an emergency call. |
| Radio on/off | Quickly switch the FM radio function on or off. |
4. Battery Information
4.1 Charging the Battery Pack
The Li-ion battery pack is not charged at the factory; please charge it before use. Charging the battery pack for the first time after purchase or extended storage (more than 2 months) may not bring the battery pack to its normal maximum operating capacity. Best operation will require fully charging/discharging the battery two or three times before the operating capacity will reach its best performance. The battery pack life may be depleted when its operating time decreases even though it has been fully and correctly charged. If this is the case, replace the battery pack.
4.2 Charger Supplied
Please use the specified charger provided by our company. Other models may cause explosion and personal injury. After installing the battery pack, and if the radio displays low battery with a voice prompt, please charge the battery.
4.3 Use Caution with the Li-ion Battery
- Do not short the battery terminals or throw the battery into a fire. Never attempt to remove the casing from the battery pack, as our company cannot be held responsible for any accident caused by modifying the battery.
- The ambient temperature should be between 5℃-40℃ (40°F - 105°F) while charging the battery. Charging outside this range may not fully charge the battery.
- Please turn off the radio before inserting it into the charger. It may otherwise interfere with correct charging.
- To avoid interfering with the charging cycle, please do not cut off the power or remove the battery during charging until the green light is on.
- Do not recharge the battery pack if it is fully charged. This may shorten the life of the battery pack or damage the battery pack.
- Do not charge the battery or the radio if it is damp. Dry it with a soft and clean cloth prior to charge.
WARNING! When keys, ornamental chain or other electric metals contact the battery terminal, the battery may become damaged or injure a human. If the battery terminals are short circuited it will generate a lot of heat. Take care when carrying and using the battery. Remember to put the battery or radio into an insulated container. Do not put it into a metal container.
4.4 How to Charge
- Plug the AC adaptor into the AC outlet, and then plug the cable of the AC adaptor into the DC jack located on the back of the charger. The indicator light blinks orange and is then ready to charge a battery.
- Plug the battery or the radio into the charger. Make sure the battery terminals are in good contact with charging terminals. The indicator light turns to red—charging begins.
- It takes approximately 2-5 hours to fully charge the battery. When the lamp lights green, the charging is completed. Remove the battery or the radio unit with its battery from the socket.
When charging a radio (with battery) the indicating lamp will not turn into green to show the fully charged status if the radio is powered on. Only when the radio is switched off will the lamp indicate normal operation. The radio consumes energy when it is power-on, and the charger cannot detect the correct battery voltage when the battery has been fully charged. So the charger will charge the battery in constant voltage mode and fail to indicate correctly when the battery has been fully charged.

4.5 LED Indicator (Charging Status)
| Status | LED Indication |
|---|---|
| No Battery | Green and red alternately flashing |
| Charge Normally | Red |
| Fully Charged | Green |
| Trouble | Red blinks fast for a long time |
Note: Trouble means battery too warm, battery short-circuited or charger short-circuited.
4.6 How to Store the Battery
- If the battery needs to be stored, keep it in a state of 80% discharged.
- It should be kept in a low temperature and dry environment.
- Keep it away from hot places and direct sunlight.
- Do not short circuit the battery terminals.
- Never attempt to remove the casing from the battery pack.
- Never store the battery in unsafe surroundings, as a short may cause an explosion.
- Do not put the battery in a hot environment or throw it into a fire, as it may cause an explosion.
4.7 Using the Type-C USB Charger
The Type-C USB charger is a convenient port that allows you to charge your Li-ion battery pack easily.
- Make sure your radio is turned OFF.
- Plug the Type-C USB cable into the Type-C USB charging port on your battery. Connect the other end of the USB charger to a wall power outlet, power bank, or car charger.
- An empty battery will be fully charged in approximately 4 hours.
- The battery meter on the LCD will move to indicate that the battery is charging.
Note:
- It is recommended to power OFF your radio while charging. However, if power is turned on while charging, you may not be able to transmit a message if the battery is completely empty. Allow time for the battery to charge to 1 bar before attempting to transmit a message.
- For optimal battery life, remove the radio from the charger within 6 hours. Do not store the radio while connected to the charger.
5. Installation of Accessories
Before the radio is ready for use, you need to attach the antenna and battery pack.
5.1 Installing/Removing the Antenna
- To install, screw the antenna clockwise into the connector on the top of the radio until it is firm.
- To remove, unscrew the antenna counter-clockwise.
5.2 Installing the Belt Clip
- Align the grooves of the belt clip with those on the back of the radio and push down until you hear a click.
- To remove the clip, use a flat-bladed object to press the belt clip tab away from the radio. Then, slide the clip upward and away from the radio.
5.3 Installing the Battery Pack
Before attaching or removing the battery, make sure your radio is turned off by turning the power/volume knob all the way counter-clockwise.
- Make sure the battery is aligned in parallel with the radio body with the lower edge of the battery about 1-2cm below the edge of the radio.
- Once aligned with the guide-rails, slide the battery upward until you hear a click as the battery locks in place.
To Remove the Battery Pack: Press the battery release above the battery pack, as you slide the battery downward.
5.4 Installing the Additional Speaker/Microphone (Optional)
Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.
6. Basic Operations
6.1 Power On/Off the Radio
To turn the unit on, simply rotate the Volume/Power knob clockwise until you hear a "click". If your radio powers on correctly there should be an audible double beep after about one second and the display will show a message or flash the LCD depending on settings for about one second. Then it will display a frequency or channel. If the Voice prompt is enabled, the voice will announce "frequency mode" or "channel mode".
To turn the unit off, turn the Volume/Power knob counter-clockwise all the way until you hear a "click". The unit is now off.
- Voice Prompt Setting: Press [MENU] to enter Menu >> 30 VOICE.
- Power on Type setting: Press [MENU] to enter menu >> 34 Power On Type to select Picture, Message, Voltage.
- If there is a power-on password set, you need to enter the correct password. Press [MENU] to enter the menu >> 37 Power-on PWD.
6.2 Adjusting the Volume
To turn up the volume, turn the Volume/Power knob clockwise. To turn the volume down, turn the Volume/Power knob counter-clockwise. Be careful not to turn it too far, as you may inadvertently turn your radio off.
By using the monitor function, enabled from the [FM broadcast/Monitor] key below the PTT, you can more easily adjust your volume by adjusting it to the un-squelched static.
6.3 Main Band/Sub Band Select
In standby mode, press the [A/B] key to switch between A (upper) and B (lower) displays. The frequency or channel on the selected display becomes the active listening and transmit frequency or channel.
Press and hold [A/B] key to quickly switch Double Wait/Signal Wait.
6.4 VFO/Channel Switch
Press the [V/M] key to switch between VFO and channel display.
- In channel mode (MR), the channel number will be displayed on the left.
- In frequency mode (VFO), the ‘VFO’ will be displayed on the left.
In MR mode, Press and hold [V/M] key to switch the frequency, channel and name display mode of the channel.
6.5 Frequency (VFO) Mode
In Frequency (VFO) mode you can navigate up and down the band by using the ▲/▼ keys. Each press will increment or decrement your frequency according to the frequency step you've set your transceiver to. You can also input frequencies directly on your numeric keypad with kilohertz accuracy.
Example: Entering the frequency 436.61250 MHz on display A
- In standby mode, press [V/M] key to switch to the frequency (VFO) mode.
- Enter [4][3][6][6][1][2][5][0] on the numeric keypad.
WARNING! Just because you can program in a channel does not mean you're automatically authorized to use that frequency. Transmitting on frequencies you're not authorized to operate on is illegal, and in most jurisdictions a serious offense. However, it is legal in most jurisdictions to listen. Contact your local regulatory body for further information on what laws, rules and regulations apply to your area.
The scanning and receive function of the aviation frequency band (AM108-136MHz) and the police frequency band (350-390MHz) is limited to use in VFO mode and allows manual input of these frequencies. Prohibit use in channel mode.
6.6 Channel (MR) Mode and Channel Selection
There are two modes of operation: Frequency (VFO) mode, and Channel or Memory (MR) mode. For everyday use, Channel (MR) mode is going to be a whole lot more practical than Frequency (VFO) mode. However, Frequency (VFO) mode is very handy for experimentation out in the field. Frequency (VFO) mode is also used for programming channels into memory.
In Channel (MR) mode you can navigate up and down the channel by using the ▲/▼ keys or the encoder. Ultimately which mode you end up using will depend entirely on your use case.
Press [V/M] key to switch the radio between VFO and Channel mode, select Channel mode.
- Operation 1: Press the ▲/▼ navigation key to select the channel.
- Operation 2: Input the channel numbers by the keypad. For example, if you want to switch to channel 12, input [0][1][2] (a total of 3 digits), and it will switch to channel 12.
When the voice prompt function is enabled, the corresponding channel will be broadcast by voice.
6.7 Making a Call
Note: Press the [A/B] key to switch the main channel to the other channel if there are 2 channels shown on the display. In standby mode, press [V/M] key to switch between frequency (VFO) mode and channel (MR) mode.
- Channel mode call: After selecting a channel, hold down the [PTT] key to initiate a call to the current channel. Speak into the microphone with normal tone. Making a call, the red LED is on.
- Frequency mode call: Press [V/M] key to switch to the frequency mode, input the working frequency within the allowable frequency range, and press and hold the [PTT] key to transmit on the current frequency. Speak into the microphone with normal tone. Making a call, the red LED is on.
- Receive a call: When you release the [PTT] key, you can answer it without any action. When receiving a call, the green LED is on.
Note: To ensure the best reception volume, keep the distance between the microphone and the mouth at the time of transmission from 2.5 cm to 5 cm.
6.8 Using the Flashlight
You can use this radio in an emergency. If you press [SK1] key, the radio turns on the high-intensity LED flashlight on your radio.
- Your radio operates normally when the emergency strobe is activated.
- (1) Press [SK1] key once, it will turn on continuously (Always On mode).
- (2) And then, press [SK1] key once, the Strobe Light emits the emergency signal (Strobe emergency mode).
- (3) And then, press [SK1] key once, the light will be turned off.
6.9 Emergency Alert
The Emergency Alert feature can be used to signal members in your group for help. To activate the emergency alert function, press and hold the [SK1] key for 3 seconds. The radio will send out a loud siren sound and the flashlight will flash.
Press the [SK1] key to exit the emergency alert function.
WARNING: The Emergency Alert feature should only be used in the event of an actual emergency.
6.10 FM Radio (FM)
The frequency ranges to listen to the radio is 65-108MHz.
- In frequency or channel mode, Press [SK2] key to turn on the radio.
- Select the desired radio frequency with the ▲/▼ keys or input the frequency. Or Press #Z to automatically search a radio station.
- Press [SK2] key to exit FM radio.
Note: While you are listening to the radio, the frequency or channel of A / B receiving signal will automatically switch to the frequency or channel mode for normal transmitting and receiving. When the signal disappears the radio will automatically switch again to FM radio mode.
6.11 Monitor
In standby, press and hold the [SK2] key to enter Monitor. When receiving matched carrier but the signaling or the signal is too weak, this function allows monitoring the weak signal.
Stop pressing the [SK2] key to turn off the speakers and return to standby mode.
If no signal, it will emit noise when you press the [SK2] Key.
6.12 Keypad Lock
The radio features a keypad lock that locks out all keys except for the three side keys. To enable or disable the keypad lock, press and hold * key for about two seconds. You can also enable so that the radio automatically locks the keypad after ten seconds from the menu.
6.13 Frequency Reversal
A short momentary press of the * key enables the reverse function. If you for some reason want to listen to the repeater's input frequency instead, press * key momentarily and you'll reverse your transmit and receive frequencies.
After activating the frequency reversal function, the first line of the screen displays "R".
6.14 TX Repeaters Tone
Press [PTT] + [SK2] key to send 1750Hz repeaters tone. This function is useful for communications through repeaters. If you have the keypad lock enabled on your radio, you can still send a 1750Hz tone the regular way without having to unlock your radio.
6.15 One Touch Frequency Search (Wireless Copy Frequency)
This feature allows you to quickly copy frequencies from another walkie-talkie.

- The radio will act as a receiver. Press and hold the 8 key, and the screen will display “SEARCH SWEEK...".
- If the transmitter continues to transmit and the unit receives an effective frequency (the strongest and stable signal), the received frequency will be displayed. If there is a CTCSS or DCS, the CTCSS or DCS value is displayed, and if there is no CTCSS or DCS, NONE is displayed.
- You can press the [MENU] key to save the Search frequency and CTCSS or DCS to the channel.
Note: During frequency Search, press the #Z key on the radio to switch between UHF or VHF bands.
6.16 Weather Radio/Scan Weather Channel (NOAA)
Your radio has a NOAA Weather Radio function, to enable the user to receive weather reports from designated NOAA stations. Your radio also has a NOAA Weather Scan function, to enable the user to scan all 10 channels of the NOAA Weather Radio.

- To turn the NOAA Weather Scan on, press the [OSQL] key for 3 seconds, the NOAA icon appears. The radio will go to Weather band mode.
- Press and hold the #Z key for 3 seconds to start automatic scanning of all 10 channels and stop on active channels. Pressing and hold the #Z key for 3 seconds during a NOAA weather scan will stop the scan.
- After stopping NOAA weather scan, it is allowed to manually select the weather channel by pressing the ▲/▼ key.
- To exit the Weather Radio broadcast mode, press the [EXIT] key or [PTT] key.
Weather Channel Frequencies and Names:
| Channel Number | RX Frequency MHz | Channel Number | RX Frequency MHz |
|---|---|---|---|
| Wx-01 | 162.550 | Wx-06 | 162.500 |
| Wx-02 | 162.400 | Wx-07 | 162.525 |
| Wx-03 | 162.475 | Wx-08 | 161.650 |
| Wx-04 | 162.425 | Wx-09 | 161.775 |
| Wx-05 | 162.450 | Wx-10 | 163.275 |
Note: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.
7. Advanced Features
7.1 Working the Menu System
The radio's menu system allows for extensive customization and configuration.
7.1.1 Basic Use (with arrow keys)
- Press the [MENU] key to enter the menu.
- Use the ▲/▼ keys to navigate between menu items.
- Once you find the desired menu item, press [MENU] again to select that menu item.
- Use the ▲/▼ keys to select the desired parameter.
- When you've selected the parameter you want to set for a given menu item:
- To confirm your selection, press [MENU] and it will save your setting and bring you back to the main menu.
- To cancel your changes, press [EXIT] and it will reset that menu item and bring you out of the menu entirely.
- To exit out of the menu at any time, press the [EXIT] key.
7.1.2 Using Shortcuts (with numerical keypad)
Every menu item has a numerical value associated with it, allowing for direct access.
- Press the [MENU] key to enter the menu.
- Use the numerical keypad to enter the number of the menu item.
- To enter the menu item, press the [MENU] key.
- For entering the desired parameter you have two options:
- Use the arrow keys as described above; or
- Use the numerical keypad to enter the numerical shortcut code.
- To confirm your selection, press [MENU] and it will save your setting and bring you back to the main menu.
7.2 Scanning
The radio features a built-in scanner for the VHF and UHF bands. In Frequency (VFO) mode it will scan in steps according to your set frequency step. In Channel (MR) mode it will scan your channels. Dual Watch is inhibited while scanning.
To enable the scanner, press and hold the #Z key for about two seconds. Press and hold the #Z key to exit scanning mode.
7.2.1 Scanning Modes
The scanner is configurable to one of three ways of operation: Time, Carrier, or Search.
Setting Scanner Mode:
- Press the [MENU] key to enter the menu.
- Enter 19 on your numeric keypad to access scanner mode.
- Press the [MENU] key to select.
- Use the ▲/▼ keys to select scanning mode (TO, CO, or SE).
- Press the [MENU] key to confirm and save.
- Press the [EXIT] key to exit the menu.
- Time Operation (TO): The scanner stops when it detects a signal, and after a factory preset time out, it resumes scanning.
- Carrier Operation (CO): The scanner stops when it detects a signal, and after a factory preset time with no signal it resumes scanning.
- Search Operation (SE): The scanner stops when it detects a signal. To resume scanning you must press and hold the #Z key again.
7.2.2 Frequency Scanning
This function scans frequencies.
- In frequency mode, press #Z key for more than 2 seconds. The radio will start scanning the frequency according to the set frequency step.
- You can change the scanning direction with the ▲/▼ keys.
- Press #Z key to stop the scanning.
Note: For Scan mode, see Menu No.19.
7.2.3 Channel Scanning
This function scans channels.
- In channels mode, press #Z key for more than 2 seconds. The radio will start scanning according to the channel you set.
- You can change the scanning direction with the ▲/▼ keys.
- Press #Z key to stop scanning.
Note: For Scan mode, see Menu No.19.
7.2.4 Scan CTCSS
This function allows scanning frequencies with CTCSS tone enabled.
- In standby mode, press [MENU] [1][6], “Scan CTCSS” will appear on the display.
- Press [MENU] key and the scan of CTCSS tones will start.
Notes: The function cannot be activated when the radio is set in Channel mode. The Scan will start only when the receiving band detects a signal.
7.2.5 Scan DCS
This function allows scanning frequencies with DCS code enabled.
- In standby mode, press [MENU] [1][7]; the display will show “Scan DCS”.
- Press [MENU] key and the scan of DCS codes will start.
Notes: The function cannot be activated when the radio is set in Channel mode. The Scan will start only when the receiving band detects a signal.
7.3 Manual Programming (Channels Memory)
Memory channels are an easy way to store commonly used frequencies so that they can easily be retrieved at a later date. The radio features 999 memory channels that each can hold: Receive and transmit frequencies, transmit power, group signaling information, bandwidth, ANI/PTT-ID settings and a six-character alphanumeric identifier or channel name.
7.3.1 Frequency Mode vs. Channel Mode
- Frequency Mode (VFO): Used for a temporary frequency assignment, such as a test frequency or quick field programming if permitted.
- Channel Mode (MR): Used for selecting preprogrammed channels.
7.3.2 Programming a Channel Repeater Offset with CTCSS Tone
Example: New memory in Channel 10: RX = 432.55000 MHz, TX = 437.55000 MHz (This is a (+ 5) Offset), TX CTCSS tone 123.0
- Press the [EXIT] key to switch between menus.
- Press [V/M] key to set the radio to VFO mode, and the VFO icon is displayed on the left.
- [MENU] [1][4] [MENU] [1] [0] [MENU] [EXIT] (Deletes Prior Data in channel 10)
- [MENU] [0][5] [MENU] 123.0 [MENU] [EXIT] (Selects desired TX encode tone)
- Enter RX frequency (Ex. 43255000)
- [MENU] [1][3] [MENU] [1][0] [MENU] >> [EXIT] (Enter the desired channel 10, RX has been added)
- Enter TX frequency (Ex. 43755000)
- [MENU] [1][3] [MENU] [1][0] [MENU] >> [EXIT] (Enter the same channel 10, TX has been added)
- Press [V/M] key to return to the MR mode and the channel number will reappear.
7.3.3 Programming a Simplex Channel with CTCSS Tone
Example: New memory in Channel 10: RX = 432.6625 MHz, TX CTCSS tone 123.0
- Press the [EXIT] key to switch between menus.
- Press [V/M] key to set the radio to VFO mode, and the VFO icon is displayed on the left.
- [MENU] [1][4] [MENU] [1] [0] [MENU] [EXIT] (Deletes Prior Data in channel 10)
- [MENU] [0][5] [MENU] 123.0 [MENU] [EXIT] (Select desired TX encode tone)
- Enter RX frequency (Ex. 43266250)
- [MENU] [1][3] [MENU] [1][0] [MENU] >> [EXIT] (Enter the desired channel 10, Channel has been added)
- Press [V/M] key to return to the MR mode and the channel number will reappear.
7.4 Repeaters Programming
The following instructions assume that you know what transmit and receive frequencies your repeater employs, and that you're authorized to use it.
- Press [V/M] key to set the radio to VFO mode, and the VFO icon is displayed on the left.
- Use the numeric keypad to enter the repeater's output (your receiving) frequency.
- Press the [MENU] key to enter the menu.
- Enter [1][2] on the numeric keypad to get to frequency offset.
- Press [MENU] key to select.
- Use the numerical keypad to enter the specified frequency offset. See the section called “12 OFFSET - Frequency shift amount” for details.
- Press [MENU] key to confirm and save.
- Enter [1][1] on the numeric keypad to get to offset direction.
- Use the ▲/▼ keys to select + (positive) or - (negative) offset.
- Press [MENU] key to confirm and save.
- Optional:
- Save to memory (see Manual programming for details).
- Set up CTCSS (see CTCSS for details).
- Press [EXIT] key to exit the menu. If everything went well, you should be able to make a test call through the repeater.
Note: If you're experiencing problems making a connection to the repeater, check your settings and/or go through the procedure again. Certain Amateur Radio repeaters (especially in Europe) use a 1750Hz tone burst to open up the repeater. To see how this is done with the radios, see the section called "1750Hz Tone-burst". If you're still unable to make a connection, contact the person in charge of the radio system with your employer or your local amateur radio club, as the case may be.
7.5 VOX (Voice Activated Transmit)
This function allows hands-free conversations: just speak in the direction of the microphone and the communication will be automatically activated.
- In standby mode, press [MENU] + 25. The screen will display “VOX Switch”. Press [MENU] key to enter the function. Press the ▲/▼ keys to turn off/turn on the VOX function.
- In standby mode, press [MENU] + 26. The screen will display “VOX Level”. Press [MENU] key to enter the function. Press the ▲/▼ keys to select the VOX level (1-9), then press [MENU] key to confirm.
To return to the standby mode press [EXIT] key.
Note: Level 1 is the least sensitive while level 9 is the most sensitive. When the radio is in Scan or FM Radio mode, the VOX is not enabled.
7.6 Dual Watch
In certain situations, the ability to monitor two channels at once can be a valuable asset. This can be achieved in one of two ways. You can either have one receiver in your radio and flip-flop between two frequencies at a fixed interval (known as Dual Watch), or you can equip a radio with two receivers (known as Dual Receive or Dual VFO). The former method is cheaper to implement and far more common than the latter. The radio features Dual Watch functionality (single receiver) with the ability to lock the transmit frequency to one of the two channels it monitors.
Enabling or Disabling Dual Watch Mode:
- Press the [MENU] key to enter the menu.
- Enter 38 on the numeric keypad to get to Dual Watch.
- Press [MENU] key to select.
- Use the ▲/▼ keys to Double Wait/Signal Wait/OFF.
- Press the [MENU] key to confirm.
- Press the [EXIT] key to exit the menu.
7.7 Stopwatch Timer
In standby mode, press [MENU] + 57. The screen displays “STOP WATCH”.
To enter the function, press [MENU]. Press the ▲/▼ keys to enable (ON) the function, then press [MENU] key for confirmation.
To return to the standby mode press [EXIT] key.
Using the Stopwatch Timer:
When this function is ON, press [MENU] key to start counting; Press [MENU] key again to re-start counting. To exit the function, stop the counting first, and then press the [EXIT] key.
7.8 DTMF (Dual-Tone Multi-Frequency)
DTMF is an in-band signaling method using dual sinusoidal signals for any given code. In two-way radio systems, DTMF is most commonly used for automation systems and remote control. A common example would be in amateur radio repeaters where some repeaters are activated by sending out a DTMF sequence.
7.8.1 DTMF Frequencies and Corresponding Codes
| 1209Hz | 1336Hz | 1477Hz | 1633Hz | |
|---|---|---|---|---|
| 697Hz | 1 | 2 | 3 | A |
| 770Hz | 4 | 5 | 6 | B |
| 852Hz | 7 | 8 | 9 | C |
| 941Hz | * | 0 | # | D |
The radio has a full implementation of DTMF, including the A, B, C and D codes. The numerical keys, as well as the *, and #Z keys correspond to the matching DTMF codes. The A, B, C and D codes are located in the [MENU], ▲/▼ and [EXIT] keys respectively.
To send DTMF codes, press the key(s) corresponding to the message you want to send while holding down the PTT key. If you have the keypad lock enabled on your radio, you can still send DTMF tones the regular way without having to unlock your radio.
7.9 Customization
The radio allows you to define visual and audible features such as Display Illumination Time, MR/Channel Mode Display Format, Power On Message, Power On password, Keypad Beep, Roger Beep, Voice Prompt, etc. to suit your usage habits.
7.9.1 Display Backlight (ABR) - MENU 51
In standby mode, press [MENU] + 51. The screen will display “ABR”. Press [MENU] key to enter the function. Press the ▲/▼ keys to select the always on/required delay time (ON/5sec/5sec/10sec/15sec/20sec) for the backlight of the display, then press [MENU] key to confirm. To return to the standby mode press [EXIT] key.
7.9.2 Beep Prompt (BEEP) - MENU 32
If you enable this function, every time a key is pressed, you will hear a Beep tone. In standby mode, press [MENU] + 32. The screen will display “BEEP PROMPT”. Press [MENU] key to enter the function. Press the ▲/▼ keys to turn ON/OFF the beep function. Press [MENU] key to confirm and exit to return to stand-by mode.
7.9.3 Voice Function (VOICE) - MENU 30
In standby mode, press [MENU] + 30; the screen will display “VOICE”. Press [MENU] key to enter the function. Press the ▲/▼ keys to select OFF/ON. Confirm your selection by pressing MENU. To return to the standby mode press [EXIT] key.
7.9.4 Language of the MENU (LANGUAGE) - MENU 29
This section shows the language of the MENU (English). In standby mode press [MENU] + 29. The display will show “LANGUAGE”.
7.9.5 Working Mode (MDF-A) - MENU 39
The radio has four working modes available: Frequency mode (FREQ), Channel mode (CH), Channel name (NAME). To shift from one mode to another one: In Standby mode press [MENU] + 39; select the desired working mode with the ▲/▼ keys. Press [MENU] key again to confirm your selection.
7.9.6 Roger Beep, End Transmission Tone (ROGER) - MENU 33
Roger Beep can be enabled/disabled:
- OFF: Roger Beep disabled
- BEEP: Roger Beep tone at the end of transmission
In standby mode, press [MENU] + 33; the screen will display “ROGER”. Press [MENU] to enter the function. Press the ▲/▼ keys to select OFF/ON. Confirm your selection by press [MENU] key. To return to the standby mode press [EXIT] key.
7.9.7 Power On Message (POWER ON MSG) - MENU 40
With this Menu you can customize the welcome message that appears on the display when the radio is switched on. Choose amongst the following options:
- VOLTAGE: The power voltage is momentarily displayed.
- MESSAGE: Welcome message.
- LOGO: Custom Pictures.
In Standby mode press [MENU] + 40. The display will show “POWER ON MSG”. Press [MENU] key to enter the function. Press the ▲/▼ keys to select the desired option and confirm with MENU. To return to the standby mode, press [EXIT] key.
7.9.8 Power On Password (Power On PWD) - MENU 37
With this Menu you can request the correct password when the radio is turned on. In standby mode, press MENU + 37. The display will show "POWER ON PWD". Press [MENU] key to enter the function. Press the ▲/▼ keys to enable/disable (ON/OFF) the power on password and confirm with MENU. To return to standby mode, press [EXIT] key.
Enable the power on password function. Each time the radio is turned on, it will display "Input Password" to prompt for the correct password. The default startup password is 000000.
7.9.9 Reset - MENU 56
This transceiver has two Reset modes available: VFO and ALL.
- Reset VFO: All the settings except channels will return to the default settings.
- Reset ALL: All settings will return to the default settings.
To Reset VFO: In standby mode, press [MENU] + 56; the screen will display “RESET”. Press [MENU] to enter the function. Press the ▲/▼ keys to select VFO, then press [MENU] to confirm. The display will show “Sure to reset?”. Press [MENU] again to confirm and the screen will display “Wait…”. Then, the transceiver will turn off and reboot again.
To Reset ALL: In standby mode, press [MENU] + 56. The screen displays “RESET”. Press [MENU] to enter the function. Press the ▲/▼ keys to select ALL, then press [MENU] to confirm. The display will show “Sure to reset?”. Press [MENU] again to confirm; the screen will display “Wait…”. Then, the transceiver will turn off and reboot again.
8. Technical Specifications
| Parameter | Specification |
|---|---|
| Frequency Band | FM65-108MHz; AM108-136MHz(Rx); 350-390MHz(Rx); 136-174MHz (Rx/Tx); 220-260MHz (Rx/Tx); 400-520MHz (Rx/Tx); 520-600MHz(Rx) |
| Memory Channels | 999 |
| Power Supply | Li-Ion battery 7.4V/1400 mAh (BL-K6) |
| Operating Temperature | -10°C to + 45°C |
| Working Mode | Monoband/Dualband |
| Modulation | F3E(FM) |
| Max. Frequency Deviation | ≤ ±5KHz |
| Spurious Radiation | < -60dB |
| Frequency Stability | ±2.5 ppm |
| Rx Sensitivity | < 0.2uV |
| Audio Output Power | ≥ 500mW |
| Dimensions (LxAxP) | 64x121x35mm |
| Weight | 240g |
| Output Power (w) | 5w-10w |
| Battery Capacity (mAh) | High Capacity |
| Waterproof / Water-Resistant | No |
| Battery Included | Yes |
| Material | Plastic |
| Maximum Range | 5km-10km |
| Flash Memory | 128KB |
| Audio Amplifier | TDA2822 |
Specifications are subject to change without notice.
WARNING: Direct plug-in ac/dc power supply must be used for disconnecting the transceiver from the mains; the desktop charger must be positioned close to the unit and easily accessible.
9. Troubleshooting Guide
| Phenomena | Analysis | Solution |
|---|---|---|
| You cannot turn on the radio. | The battery may be installed improperly. The battery power may run out. The battery may suffer from poor contact caused by dirty or damaged battery contacts. | Remove and reattach the battery. Recharge or replace the battery. Clean the battery contacts or replace the battery. |
| During receiving, the voice is weak or intermittent. | The battery voltage may be low. The volume level may be low. The antenna may be loose or incorrectly installed. The speaker may be blocked. | Recharge or replace the battery. Increase the volume. Turn off the radio, then remove and reattach the antenna. Clean the surface of the speaker. |
| You cannot communicate with other group members. | The frequency or signaling type may be inconsistent with that of other members. You may be too far away from other members. | Verify that your TX/RX frequency and signaling type are correct. Move towards other members. |
| You hear unknown voices or noise. | You may be interrupted by radios using the same frequency. The radio in analog mode may be set with no signaling. | Change the frequency, or adjust the squelch level. Request your dealer to set signaling for the current channel to avoid interference. |
| You are unable to hear anyone because of too much noise and hiss. | You may be too far away from other members. You may be in an unfavorable position (e.g., communication blocked by high buildings or underground area). | Move towards other members. Move to an open and flat area, restart the radio, and try again. |
| The radio keeps transmitting. | It may be the result of external disturbance (e.g., electromagnetic interference). VOX may be turned on or the headset is not installed in place. | Stay away from equipment that may cause interference. Turn off the VOX function. Check that the headphones are in place. |
Note: If the above solutions cannot fix your problems, or you have other queries, please contact your dealer for more technical support.
10. User Tips
- Software Installation: The radio supports PC programming. While the device does not come with pre-installed software, you can use a programming cable and compatible software to customize frequencies and settings. Ensure you read the factory software data before making changes to avoid errors.
- Display: The UV-K61 features a color LCD screen for clear display of frequencies, channels, and status.
- Frequency Copy: Utilize the "Wireless Copy Frequency" feature (One Touch Frequency Search) to quickly clone frequencies from other walkie-talkies, simplifying setup for group communication.
- Charging: Take advantage of the versatile Type-C charging option for convenience, especially when away from a base charger. You can charge it with a power bank or in your car.
11. Warranty and Support
For any technical support, warranty claims, or further inquiries, please contact your authorized Baofeng dealer or the point of purchase. Ensure you retain your proof of purchase for warranty purposes.
Disclaimer: The accuracy and completeness of the contents are sought in the process of compilation, but we do not bear any responsibility for possible errors or omissions. With the continuous development of technology, we reserve the right to change the design and specification of the product without notice. No copy, modification, translation and dissemination of this handbook may be made in any form without the prior written authorization of our department.
Fujian Baofeng Electronics Co., Ltd.
Changfu Industrial Zone, Xiamei, Nan'an, Quanzhou, Fujian, China