JIKONG JK-BD4A24S10P

Contents

JK-BD4A24S10P Smart BMS User Manual

For LiFePo4, Li-Ion, and LTO Battery Packs (4S-24S)

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the JIKONG JK-BD4A24S10P Smart Battery Management System (BMS). This advanced BMS is designed to protect and manage LiFePo4, Li-Ion, and LTO battery packs ranging from 4S to 24S configurations, offering active balancing, comprehensive protection features, and Bluetooth connectivity for APP monitoring and control.

Please read this manual thoroughly before installation and use to ensure safe and optimal performance of your battery system.

2. Package Contents

Upon opening the package, verify that all components are present and undamaged:

  • JK-BD4A24S10P Smart BMS Unit
  • Balance Wires Harness
  • Temperature Sensors (if included with specific model variant)
  • Mounting Screws
JIKONG JK-BD4A24S10P Smart BMS unit with balance wires and mounting screws
Figure 2.1: JK-BD4A24S10P Smart BMS and included accessories.

3. Setup and Installation

Proper installation is crucial for the safe and effective operation of the BMS. Follow these steps carefully:

3.1 Wiring Diagram

Refer to the following wiring diagram for connecting the BMS to your battery pack, charger, and load. Ensure all connections are secure and correctly polarized.

Detailed wiring diagram for JIKONG Smart BMS showing connections for battery, charger, load, and balance wires.
Figure 3.1: BMS Wiring Diagram. Connect B- to the negative terminal of the battery pack. P- is the common negative terminal for both charge and discharge. The balance wires connect to each cell in series, starting from B0 (negative of the first cell) up to the positive of the last cell (Bn).

Important: Always connect the balance wires to the battery pack first, starting from B0 (the main negative terminal of the battery pack) and proceeding sequentially to B1, B2, and so on, up to the positive terminal of the last cell (Bn). After connecting the balance wires, connect the main B- wire from the BMS to the main negative terminal of the battery pack. Finally, connect the P- wire to your load/charger negative terminal.

3.2 APP Installation and Connection

The JIKONG Smart BMS features built-in Bluetooth for monitoring and control via a dedicated mobile application. To download the APP:

  1. Scan the QR code located on the BMS unit or visit www.jk-bms.com to download the official APP.
  2. Install the APP on your smartphone.
  3. Ensure Bluetooth is enabled on your phone.
  4. Open the JIKONG BMS APP and search for available BMS devices.
  5. Select your BMS from the list to connect. The default password (if prompted) is usually '123456' or '888888'.
JIKONG Smart BMS unit showing QR code for APP download and website address.
Figure 3.2: BMS unit with APP download QR code.

4. Operating Instructions

4.1 Active Balancing Function

The JIKONG Smart BMS incorporates an active balancing feature. This technology transfers energy from higher voltage cells to lower voltage cells, ensuring all cells in the pack maintain a similar voltage level. This process extends the overall lifespan and improves the performance of your battery pack.

Diagram illustrating active balancing where energy is transferred from high voltage cells to low voltage cells.
Figure 4.1: Active Balancing Principle.

4.2 APP Interface Overview

The mobile APP provides real-time monitoring and configuration options for your BMS. Key screens include:

  • Status: Displays current battery voltage, current, power, capacity, cycle count, individual cell voltages, and temperature.
  • Settings: Allows configuration of various protection parameters such as overcharge voltage, undervoltage protection, overcurrent limits, and temperature thresholds.
  • Control: Provides options to enable/disable charging and discharging, and other control functions.
Screenshots of the JIKONG BMS mobile application showing Status, Settings, and Control interfaces with various battery parameters.
Figure 4.2: JIKONG BMS APP Interface.

4.3 Block Diagram

The internal architecture of the JIKONG Active Balancing Protection Board includes several modules for comprehensive battery management:

Block diagram of the JIKONG Active Balancing Protection Board, showing MCU, MOS driver circuit, current acquisition, Bluetooth module, active balancing module, power module, and various interfaces.
Figure 4.3: BMS Internal Block Diagram.

Key components include the MCU (Microcontroller Unit) for overall control, MOS driver circuits for power switching, current acquisition for monitoring, a Bluetooth module for wireless communication, and an active balancing module for cell equalization. It also supports various interfaces like RS485, LCD, GPS, CAN, and modules for heating, parallel operation, and alarms.

5. Maintenance

To ensure the longevity and optimal performance of your JIKONG Smart BMS and battery pack, consider the following maintenance tips:

  • Regular Monitoring: Periodically check the battery status via the APP to ensure all cells are balanced and operating within safe parameters.
  • Clean Connections: Ensure all wiring connections are clean and free from corrosion. Loose connections can lead to resistance and heat buildup.
  • Environmental Conditions: Operate the BMS and battery pack within the recommended temperature range. Avoid extreme heat or cold.
  • Firmware Updates: Check the official JIKONG website or APP for any available firmware updates for your BMS model.

6. Troubleshooting

If you encounter issues with your JIKONG Smart BMS, consider the following common troubleshooting steps:

  • BMS Not Powering On:
    • Check all main power connections (B- and P-) for proper contact and polarity.
    • Verify that the balance wires are correctly connected to each cell and the main harness is plugged into the BMS.
    • Ensure the battery pack voltage is within the operational range of the BMS.
  • Bluetooth Connection Issues:
    • Ensure Bluetooth is enabled on your smartphone and the APP has necessary permissions.
    • Move closer to the BMS unit to improve signal strength.
    • Restart the APP or your phone.
    • Check if other Bluetooth devices are interfering.
  • Unbalanced Cells:
    • Confirm that the active balancing function is enabled in the APP settings.
    • Allow sufficient time for the active balancing to work, especially after initial setup or deep discharge.
    • Inspect balance wires for damage or loose connections.
  • Over-protection Triggered (Overcharge, Overdischarge, Overcurrent, Overtemperature):
    • Check the APP for specific fault codes or warnings.
    • Verify that your charger and load are within the BMS's specified current limits.
    • Ensure the battery pack is not being charged or discharged beyond its safe voltage limits.
    • Check temperature sensors and ensure proper ventilation around the battery and BMS.

If the problem persists, contact JIKONG technical support for further assistance.

7. Specifications

7.1 General Specifications

Parameter Value Unit
Supply voltage 20-100 V
Operating power consumption ≤800 mW
Operating temperature -30 to 70 °C
Maximum number of collection strings 24 String
Maximum balancing current 0.4 A
Maximum charging current 100 A
Maximum discharge current 100 A
Maximum instantaneous current 200 A
Maximum internal loop resistance 1 mΩ
Protective plate size 146.8*83*17.6 mm
Finished weight 230 g
Table of general specifications for the JIKONG Smart BMS, including voltage, current, temperature, and physical dimensions.
Figure 7.1: General Specifications Table.

7.2 Protection Parameters

NUM Parameter LI-ION LIFEPO4 LTO Unit
1(balancing initial voltage)332V
2(Maximum balancing current)0.40.40.4A
3(Unit overcharge voltage)4.23.62.7V
4(Single overcharge protection recovery)4.183.552.65V
5(Monomer undervoltage protection)2.822.61.8V
6(Single undervoltage protection recovery)2.852.651.85V
7(Automatic shutdown voltage)2.82.51.7V
8(SOC-0% voltage)2.92.61.85V
9(SOC-100% voltage)4.183.52.65V
10(Trigger balancing differential pressure)0.010.010.01V
11(Charging overcurrent protection delay)303030(S)
12(Charge overcurrent protection release time)606060(S)
13(Discharge overcurrent protection delay)300300300(S)
14(Discharge overcurrent protection release time)606060(S)
15(Short-circuit protection delay)150015001500(uS)
16(Short circuit protection release time)606060(S)
17Charging overtemperature protection temperature707070°C
18(Charge overtemperature restore temperature)606060°C
19(Discharge overtemperature protection temperature)707070°C
20(Discharge overtemperature recovery temperature)606060°C
21(Charging low temperature protection temperature)-20-20-20°C
22(Charge low temperature to restore temperature)-10-10-10°C
23(MOS Overtemperature protection temperature)100100100°C
24(MOS Overtemperature recovery temperature)808080°C
Table detailing protection parameters for Li-Ion, LiFePO4, and LTO battery types, including voltage, current, and temperature thresholds.
Figure 7.2: Protection Parameters Table.

8. User Tips

  • Initial Balance: For new battery packs, allow the BMS to perform an initial balance cycle. This may take some time, especially if cells are significantly out of balance.
  • Temperature Monitoring: Pay attention to temperature readings, especially during high charge/discharge rates. Excessive heat can degrade battery performance and lifespan.
  • Wiring Accuracy: Double-check all wiring connections before applying power. Incorrect wiring is a common cause of BMS malfunction.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or visit the official JIKONG BMS website at www.jk-bms.com. Keep your purchase records for warranty claims.

© 2024 JIKONG. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.