ASYPDZSW SPK-2

Contents

ASYPDZSW SPK-2 UPC1237 Speaker Protection Module User Manual

Independent Channel Speaker Protection for Audio Amplifiers

1. Introduction

The ASYPDZSW SPK-2 is a pair of left and right split independent speaker protection modules designed to safeguard your audio power amplifier and speakers. Utilizing the UPC1237 protection chip as its core, this module offers essential features such as delayed startup, DC protection, and power-off anti-shock capabilities.

Each module incorporates a fully sealed 5A high-current silver-contact transparent Omron relay. With dual parallel independent channel output, the current capacity is doubled, resulting in lower internal resistance and improved sound transmission. These modules are widely applicable for protecting most independent channel output speakers and are particularly suitable for Class A power amplifiers.

Two finished ASYPDZSW SPK-2 speaker protection boards, top-down view.
Figure 1: Finished ASYPDZSW SPK-2 Speaker Protection Boards

2. Product Options

The ASYPDZSW SPK-2 speaker protection module is available in two configurations:

  • DIY Kit: This option includes all necessary components for assembly. Users are required to solder and test the parts themselves.
  • Finished Board: This option provides fully assembled, welded, and tested boards, ready for installation.
Components of the ASYPDZSW SPK-2 DIY Kit, including PCBs and various electronic parts.
Figure 2: ASYPDZSW SPK-2 DIY Kit Components

3. Setup and Installation

Carefully follow these instructions for proper installation of your SPK-2 module. Ensure all power is disconnected from your amplifier before beginning installation.

3.1. Board Layout and Connections

Refer to the diagram below for the physical dimensions and connection points on the PCB. Each module is designed for a single channel (Left or Right).

PCB layout diagram of the ASYPDZSW SPK-2 module showing dimensions (60mm x 55mm), hole diameter (10mm), terminal spacing (30mm), and connection points for GND AC, AC, Input, L-CH/R-CH, and LED.
Figure 3: SPK-2 PCB Layout and Connection Diagram

Key Connection Points:

  • GND AC / AC: Power input (AC 0-12V). If using DC 12V, connect the negative pole to the GND point.
  • INPUT: Audio signal input from your amplifier.
  • L-CH / R-CH: Speaker output terminals. Connect to your left or right speaker.
  • LED: Status indicator (typically illuminates when the speaker is connected).

3.2. Wiring Instructions

  1. Power Supply: Connect an AC 0-12V power source to the "GND AC" and "AC" terminals. If using a DC 12V supply, ensure the negative terminal of the DC supply is connected to the "GND" point on the board.
  2. Audio Input: Connect the audio output from your power amplifier to the "INPUT" terminal on the protection board.
  3. Speaker Output: Connect your speaker to the "L-CH" (for left channel board) or "R-CH" (for right channel board) terminals.
  4. Grounding: Ensure proper grounding throughout your audio system to prevent hum and noise.

Important Note: This module features a common negative design where the power supply, speaker input, and speaker output share a common negative. This design may not be compatible with Class D amplifiers. Attempting to use it with a Class D amplifier could result in malfunction or damage.

4. Operating Instructions

Once properly installed and powered on, the SPK-2 module operates automatically to protect your audio system.

  • Delayed Startup: Upon power-up, the module will introduce a short delay before connecting the speakers. This prevents the "thump" or "pop" sound often heard when an amplifier stabilizes. The LED indicator will typically light up after this delay, signifying that the speakers are connected.
  • DC Protection: The UPC1237 chip continuously monitors for DC voltage at the amplifier's output. If a significant DC offset is detected (which could damage speakers), the relays will immediately disconnect the speakers to prevent damage.
  • Power-off Anti-Shock: When the amplifier is powered off, the module quickly disconnects the speakers to prevent any transient "pop" sounds or voltage spikes that might occur during shutdown.
Close-up view of the Omron relay on the ASYPDZSW SPK-2 board, highlighted with a red circle.
Figure 4: Omron Relay on the SPK-2 Board

5. Maintenance

The ASYPDZSW SPK-2 module is designed for reliable, long-term operation with minimal maintenance.

  • Cleaning: Keep the boards free from dust and debris. Use a soft, dry brush or compressed air for cleaning. Do not use liquid cleaners.
  • Inspection: Periodically inspect the solder joints (especially for DIY kits) and connections for any signs of corrosion or loosening.
  • Environment: Ensure the module is installed in a well-ventilated area, away from excessive heat, moisture, and strong electromagnetic fields.

6. Troubleshooting

If you encounter issues with your SPK-2 module, consider the following:

  • No Speaker Connection (No Sound):
    • Verify the power supply voltage is within the specified AC 0-12V range.
    • Check all wiring connections for correctness and secure contact.
    • Ensure the amplifier is stable and not outputting DC voltage, which would trigger protection.
    • Confirm the LED indicator lights up after the startup delay. If not, recheck power and input connections.
  • "Pop" Sound During Power On/Off:
    • This module is designed to prevent such sounds. If they occur, re-verify all connections, especially the input from the amplifier and the speaker outputs.
    • Ensure the power supply to the protection board is stable.
  • Incorrect Channel Boards Received:
    • While the boards are largely identical, they are labeled L-CH and R-CH. If you received two boards for the same channel, they can often still function for the opposite channel, but verify the input/output labels carefully.
  • Incompatibility with Class D Amplifiers:
    • As noted in the setup section, this module's common negative design makes it unsuitable for most Class D amplifiers. If you are using a Class D amplifier and experience issues, this is likely the cause.

7. Specifications

FeatureSpecification
Model NumberSPK-2
Protection ChipUPC1237
Input VoltageAC 0-12V (DC 12V also possible, connect '-' to GND)
Channels2 (Left and Right independent modules)
Relay TypeFully sealed 5A high current silver contact transparent Omron relay
Terminal Spacing30mm
Hole DiameterΦ 10mm
PCB Size60mm x 55mm
Maximum Power Per ChannelNO POWER (This module is for protection, not amplification)
PackageYes
OriginMainland China

8. User Tips

  • Many users praise the overall quality and performance of these modules, noting them as a reliable choice for speaker protection.
  • When assembling the DIY kit, take your time with soldering to ensure clean and strong connections. The double-sided PCB is of good quality.
  • Always double-check the channel labels (L-CH, R-CH) during installation, although functionally, they are often interchangeable if correctly wired.
  • Be mindful of the module's common negative design; it is crucial to confirm compatibility with your amplifier type, especially if it's a Class D amplifier.

9. Warranty and Support

For any questions, technical assistance, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase records for reference.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.