1. Introduction
This manual provides essential information for the proper handling, pre-installation, and general use of the POKESS Crankshaft Rear Oil Seal (Model: BM5G6K301AC). This component is designed to prevent oil leaks from the crankshaft, ensuring optimal engine performance and longevity. Please read all instructions carefully before proceeding with installation or use.
For detailed technical specifications and additional guidance, you may refer to the official user manual PDF: Product Manual (PDF).
2. Important Safety Information
Failure to follow these instructions may result in damage to the product or personal injury.
- Warning: Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture.
- Handle with care to avoid cuts or injuries.
3. Product Information & Specifications
| Attribute | Detail |
|---|---|
| Product Name | Crankshaft Rear Oil Seal |
| Brand Name | POKESS |
| Model Number / OEM NO. | BM5G6K301AC |
| Function | Replacement & repair for vehicle parts, preventing oil leaks |
| Origin | Mainland China |
| High-concerned chemical | none |
| Package Contents | Main part + accessories + hardware |
| Package Length | 20 cm |
| Package Width | 20 cm |
| Package Height | 20 cm |
| Package Weight | 0.3 kg |
Compatible Vehicle Models:
- FOCUS 2012-2014, 2015-
- ECOSPORT
- TAURUS
- ESCORT
- KUGA 2013-2016
- MONDEO 2013-
- FIESTA 2013-
Note: The compatibility information is for reference only. Before purchase, please compare the Part Number (BM5G6K301AC) with your original part. It must be the same for correct replacement.
4. Pre-Installation Check (Setup)
Before beginning the installation process, perform the following checks:
- Verify OE Number: Confirm that the OE number of this part (BM5G6K301AC) is 100% identical to your original broken part. If the OE Number is correct, proceed with installation. If the OE Number is wrong, do not install and contact the seller immediately.
- Check Package Contents: Ensure all components (main part + accessories + hardware) are present and undamaged.
- Confirm Vehicle Match: Verify that the part matches your specific vehicle model, year, and the intended installation position.
5. Installation (Operating)
Installation of a crankshaft rear oil seal is a complex automotive procedure that typically requires specialized tools and expertise. Incorrect installation can lead to severe engine damage and oil leaks.
- Professional Installation Recommended: It is highly recommended that this part be installed by a qualified and certified automotive technician.
- Consult Service Manual: Refer to your vehicle's specific service manual for detailed, step-by-step installation instructions, torque specifications, and any special tools required.
- Cleanliness: Ensure all mating surfaces are thoroughly cleaned and free of old gasket material, oil, or debris before installation.
- Lubrication: Apply a thin coat of clean engine oil to the sealing lip of the new seal before installation to aid in proper seating and prevent damage during initial engine startup.
6. Maintenance
Once installed, the crankshaft rear oil seal is designed for long-term performance. Regular maintenance involves:
- Routine Inspections: Periodically check for any signs of oil leaks around the rear of the engine, especially during oil changes or other under-vehicle inspections.
- Engine Health: Ensure your engine is properly maintained, including regular oil changes with the correct type and viscosity of oil, as this can impact seal longevity.
7. Troubleshooting
If you experience oil leaks after installation, consider the following:
- Re-inspection: A professional should re-inspect the installation to ensure the seal was seated correctly and not damaged during the process.
- Surface Condition: Verify that the crankshaft sealing surface and engine block mating surface are smooth and free from nicks or corrosion.
- Part Compatibility: Double-check that the correct OE number part was used for your specific vehicle.
For persistent issues, consult a certified automotive mechanic.
8. Manufacturer & EU Representative Information
- Manufacturer: SUCCESS COURIER SL
- EU Authorized Representative: CALLE RIO TORMES NUM. 1, PLANTA 1, DERECHA, OFICINA 3, Fuenlabrada, Madrid, 28947
- Importer: No. 1686-1688, 1702-1716 Jinyongfu Auto Parts Supplies City, No. 1686-16816, Guangyuan East Road, Yuexiu District, Guangzhou City, Guangdong Province (cannot be used as a factory)
9. Compliance Information
This product is an automotive mechanical component. For electrical or electronic products, compliance with electrical safety, electromagnetic compatibility, or environmental regulations (e.g., CE marking) and related documentation may be required. This product is not a toy and does not fall under toy safety regulations.
10. Warranty & Support
For warranty information, technical support, or any questions regarding this product, please contact the seller directly through the platform where the purchase was made. Keep your purchase records for reference.