BAOFENG UV-K6

Contents

Baofeng UV-K6 Multi-Band Amateur Radio User Manual

Model: UV-K6 | Brand: BAOFENG

1. Introduction and Safety Information

Thank you for choosing the Baofeng UV-K6 Multi-Band Amateur Radio. This device utilizes advanced technology to provide reliable communication in demanding environments. It features a sleek and compact design, offering emergency alarm, personnel death alarm, work alone mode, analog DTMF, 2TONE, 5TONE, CTCSS/DCS encode/decode. It is suitable for both professional and recreational users.

1.1 Important Safety Warnings

WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

ATTENTION! When programming the radio, always read the factory software data first before rewriting. Errors may occur otherwise. Use a programming cable with a PC to ensure compliance with FCC (or EU other country) license certification.

ATTENTION! Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the radio. This guide contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations.

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.

FRS, GMRS, MURS, PMR446: Note that there are restrictions on these bands that make this transceiver illegal for use in these specific services.

1.2 RF Exposure Compliance and Control

To control your exposure and ensure compliance with occupational/controlled environmental exposure limits, always adhere to the following procedures:

  • Do not remove the RF Exposure Label from the device.
  • User awareness instructions should accompany the device when transferred to other users.
  • Do not use this device if the operational requirements described herein are not met.

Operating Instructions:

  • Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), press the Push-to-Talk (PTT) key. To receive calls, release the [PTT] key.
  • Keep the radio unit at least 2.5cm away from the face.
  • When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product.
  • Use of non-approved antennas, batteries, and accessories causes the radio to exceed FCC RF exposure guidelines.

Operating Prohibitions:

  • Do not operate the product in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials.
  • Do not operate the product near or in any blasting area.
  • Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
  • Do not hold the product while driving.
  • Do not operate the product in any area where use of wireless communication equipment is completely prohibited.

2. Package Contents

The Baofeng UV-K6 transceiver comes with the following items:

  • 1 Radio body
  • 1 Lithium-Ion battery pack
  • 1 Antenna
  • 1 Desk charger (with wall-wart)
  • 1 Belt Clip
  • 1 Wrist Belt
  • 1 Instruction Manual (PDF version available online, see User manual (PDF))
Image showing the Baofeng UV-K6 radio, antenna, battery, base charger, Type-C cable, clip, lanyard, and manual.
Figure 2.1: Included Accessories and Key Parameters. The table in the image lists Model: UV-K6, Power: High Power, Distance: Long Range, Battery: High Capacity, Frequency: 6 Bands, Channel: 999 Channels, Function 1: Wireless Copy Frequency, Function 2: Air Band.

3. Features and Functions

The Baofeng UV-K6 offers a comprehensive set of features for versatile communication:

  • 1.54" TFT large screen, full keyboard, fully open menu operation.
  • Wireless Copy Frequency: Allows quick frequency copying from other radios.
  • Multi-Band Reception:
    • FM: 65-108 MHz (RX)
    • AM: 108-136 MHz (Air Frequency Receiving)
    • 350-390 MHz (RX)
    • 136-174 MHz (TX/RX)
    • 220-260 MHz (TX/RX)
    • 400-520 MHz (TX/RX)
    • 520-600 MHz (RX)
  • NOAA Weather Radio: Channel reception and weather alerts for the United States and Canada (10 NOAA Weather Stations).
  • 999 Memory Channels: Up to 640 named memory channels.
  • Type-C Charging: Direct Type-C charging port and charging stand for convenient battery life.
  • High Capacity Lithium-Ion Battery.
  • DTMF: Encoder and manual dial.
  • VOX: Voice activated transmit.
  • FM Radio: Broadcast FM radio receiver 87.5-108 MHz.
  • LED Flashlight: Built-in LED spotlight for illumination.
  • Alarm Function: Emergency alarm.
  • Dual Watch / Dual Reception.
  • Scanner Function: VFO scan range setting, three scan recovery methods, channel scan, CTC/DCS scan.
  • PC Programmable: Can be programmed via computer software.
  • Keypad Programmable: Most settings can be adjusted directly from the keypad.
  • Squelch: Ten (10) levels of Squelch adjustment.
  • End of Transmission Tone: "Roger Beep".
  • Accessory Port: Two (2) pins for Kenwood accessory port.
Image showing various features of the Baofeng UV-K6 radio with icons: Wireless Copy Frequency, 6 Bands, 999 Channels, High Power, High Capacity, DTMF, Stopwatch Function, Type-C Charging, NOAA, LED Flashlight, VOX Function, FM Radio.
Figure 3.1: Key Features Overview.
Image detailing the AM/FM Aviation Band Receiving capabilities and 6 frequency bands: FM 65-108 MHz (RX), AM 108-136 MHz (RX), 350-390 MHz (RX), 136-174 MHz (RX&TX), 220-260 MHz (RX&TX), 400-480 MHz (RX&TX), 400-520 MHz (RX).
Figure 3.2: Frequency Band Coverage.

4. Setup and Installation

4.1 Battery Information and Charging

The Li-ion battery pack is not charged at the factory. Please charge it before first use. For optimal performance, fully charge/discharge the battery two or three times.

Use Caution with the Li-ion Battery:

  • Do not short the battery terminals or throw the battery into a fire.
  • The ambient temperature for charging should be between 5℃-40℃ (40°F - 105°F).
  • Turn off the radio before inserting it into the charger to avoid interference with charging.
  • Do not remove the battery or unplug the power cord during charging until the green light is on.
  • Do not recharge a fully charged battery.
  • Do not charge a damp battery or radio.
  • Do not put the battery in a hot environment or throw it into a fire.

4.1.1 How to Charge (Base Charger)

  1. Plug the AC adaptor into an AC outlet, then plug the cable into the DC jack on the back of the charger. The indicator light blinks orange, ready to charge.
  2. Plug the battery or the radio into the charger. Ensure good contact with charging terminals. The indicator light turns red.
  3. Full charge takes approximately 2-5 hours. When the lamp lights green, charging is complete.

Note: If the radio is powered on while charging, the indicator may not turn green to show full charge. Always switch off the radio for accurate charging indication.

4.1.2 Type-C USB Charging

The Type-C USB charger provides a convenient way to charge your Li-ion battery pack.

  1. Ensure your radio is turned OFF.
  2. Plug the Type-C USB cable into the Type-C USB charging port on your battery. Connect the other end to a wall power outlet or compatible USB power source.
  3. An empty battery will be fully charged in approximately 4 hours.
  4. The battery meter on the LCD will indicate charging status.

Note: It is recommended to power OFF your radio while charging. For optimal battery life, remove the radio from the charger within 6 hours. Do not store the radio while connected to the charger.

Image showing two charging methods for the Baofeng UV-K6: Type-C Fast Charging with a USB cable connected to a power bank, and Base Charging using the included desktop charger.
Figure 4.1: Charging Methods (Type-C and Base Charger).

4.2 Installation of Accessories

Before using the radio, attach the battery pack and antenna.

4.2.1 Installing/Removing the Antenna

  • Installing: Screw the antenna into the connector on top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
  • Removing: Turn the antenna counter-clockwise to remove it.

4.2.2 Installing the Belt Clip

  • At the back of the radio, remove the two parallel screws mounted above the battery. Thread them through the holes on the belt clip and screw them back into the radio body.
  • To remove the belt clip, unscrew counter-clockwise.

4.2.3 Installing the Battery Pack

Ensure the radio is turned off by rotating the power/volume knob counter-clockwise.

  1. Align the battery in parallel with the radio body, with the lower edge of the battery about 1-2cm below the edge of the radio.
  2. Slide the battery upward along the guide-rails until you hear a click, indicating it's locked in place.

To remove the battery, press the battery release above the battery pack and slide the battery downward.

4.2.4 Installing Additional Speaker/Microphone (Optional)

Pry open the rubber MIC-Headset jack cover and insert the Speaker/Microphone plug into the double jack.

Diagram of the Baofeng UV-K6 radio with numbered parts: 1. Antenna, 2. PTT Key, 3. Flashlight / Alarm Switch, 4. Radio / Monitor, 5. A / B Select Key, 6. SWEEP Key, 7. MENU Key, 8. Color LCD, 9. Accessory Jack, 10. V/M-VFO/MR Mode Key, 11. Speaker, 12. EXIT Key, 13. Type-C charging indicator, 14. Type-C charging port, 15. LED flashlight, 16. Color LCD, 17. Speaker, 18. Microphone, 19. EXIT Key, 20. Keypad.
Figure 4.2: Radio Overview - Buttons and Controls.

5. Operating Instructions

5.1 Basic Operations

5.1.1 Power On/Off

  • To turn on: Rotate the Volume/Power knob clockwise until you hear a "click". The display will show a message or flash the LCD, then display a frequency or channel.
  • To turn off: Rotate the Volume/Power knob counter-clockwise until you hear a "click".

5.1.2 Adjusting the Volume

  • To increase volume: Rotate the Volume/Power knob clockwise.
  • To decrease volume: Rotate the Volume/Power knob counter-clockwise.

5.1.3 Main Band/Sub Band Switch

Press the [A/B] key to switch between the A (upper) and B (lower) displays. The selected display becomes the active listening and transmit frequency or channel.

5.1.4 VFO/Channel Switch

Press the [V/M] key to switch between Frequency (VFO) Mode and Memory (MR) (Channel) Mode. VFO mode is useful for experimentation, while Channel mode is practical for everyday use with stored frequencies.

5.1.5 Frequency (VFO) Mode

In VFO mode, use the ▲/▼ keys to increment or decrement the frequency according to the set frequency step. You can also input frequencies directly using the numeric keypad (e.g., for 436.61250 MHz, input [4][3][6][6][1][2][5][0]).

WARNING! Transmitting on unauthorized frequencies is illegal. Always ensure you have proper authorization.

5.1.6 Channel (MR) Mode and Channel Selection

Press the [V/M] key to switch to Channel mode. Select channels using the ▲/▼ navigation keys or by inputting channel numbers directly (e.g., for channel 12, input [0][1][2]).

5.1.7 Making a Call

  • Channel mode call: Select a channel, then hold down the [PTT] key to transmit. Speak into the microphone with a normal tone. The red LED will be on.
  • Frequency mode call: Switch to VFO mode, input the desired frequency, then hold down the [PTT] key to transmit.
  • Receiving a call: Release the [PTT] key. The green LED will be on when receiving.

Note: For best reception volume, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.

5.2 Advanced Features

5.2.1 Emergency Alert

To activate the emergency alert, press the pre-programmed [SOS] key. Press it again to exit. Alarm types can be configured via the MENU (Menu>>49/65 Alarm Mode) or CPS program software.

WARNING: The Emergency Alert feature should only be used in an actual emergency.

5.2.2 FM Radio (FM)

Press the [MENU] key, then navigate to the pre-programmed [FM Radio] function (via SK1/SK2) to turn it on/off. To search for a station, briefly press the [#z] key. The radio will display 'Seeking...' and lock onto the current frequency. Press and hold [#z] to enter radio search mode and automatically save the searched frequency as a channel.

5.2.3 Radio Interrupt

  • On: Allows receiving or transmitting on the channel even when FM radio is in use.
  • Off: Prevents transmission or reception when FM radio is in use.

5.2.4 Monitor

Press the pre-programmed [Monitor] key to enter Monitor mode. This allows you to hear weak signals or signals with matched carriers but weak signaling. Press [Monitor] again to exit.

5.2.5 Keypad Lock

To enable or disable the keypad lock, press and hold the [*] key for about two seconds. The radio can also be set to automatically lock the keypad after ten seconds via the menu.

5.2.6 Frequency Reversal

A short momentary press of the [*] key enables the reverse function, allowing you to listen to the repeater's input frequency or reverse your transmit and receive frequencies.

5.2.7 TX Repeaters Tone (1750Hz)

The radio supports 1750Hz, 1000Hz, 1450Hz, and 2100Hz tone-bursts for repeater activation. The SK1/SK2 programmable key can be defined as the "1750Hz" function. Press the pre-programmed [1750Hz] key to send tone-bursts.

5.2.8 NOAA Weather/Weather Alert

The radio has a NOAA Weather Radio function to receive weather reports from designated NOAA channels (WX1-WX10). In standby mode, press and hold the [0] key to enter NOAA channel scanning reception state. The radio will broadcast hazard weather alerts and can automatically switch to weather broadcast mode.

Image showing the Baofeng UV-K6 radio with a display indicating 10 NOAA Weather Stations and FM Radio. The text states 'Broadcast the Hazard weather at the first time, earns a critical time for you to get full preparation'.
Figure 5.1: NOAA Weather Radio Feature.

Press [MENU] then use the pre-programmed [One Touch Sweep] key (via SK1/SK2) to enter frequency search mode. The screen will display "Seeking..." and the indicator light will be yellow. Upon successful search, the frequency and CTCSS/DCS will be displayed, and the speaker will turn on. You can save the search frequency and CTCSS/DCS to a channel by pressing [MENU].

Diagram illustrating the steps to decode another walkie talkie's frequency. Step 1: Power on, press key, screen displays 'SEARCH SWEEK...'. Step 2: Press and hold other radio's transmitting frequency, press MENU to confirm when it searches for another frequency. Step 3: Switch to channel mode to see the other person's frequency and communicate.
Figure 5.2: Wireless Copy Frequency Steps.

5.2.10 Scanner

The radio features a built-in scanner for VHF and UHF bands. In VFO mode, it scans in steps according to your set frequency step. In Channel (MR) mode, it scans your channels. To enable the scanner, press and hold the [#z] key for about two seconds. Change scanning direction with ▲/▼ keys. Press and hold [#z] again to exit.

Scan Modes:

  • Time Operation (TO): Scanner stops when a signal is detected, then resumes after a factory preset time.
  • Carrier Operation (CO): Scanner stops when a signal is detected, then resumes after the signal disappears.
  • Search Operation (SE): Scanner stops when a signal is detected and does not resume automatically.

5.2.11 DTMF (Dual-Tone Multi-Frequency)

DTMF is an in-band signaling method used for automation systems and remote control. The radio has full DTMF implementation. To send DTMF codes, press the corresponding key(s) while holding down the PTT key.

DTMF Frequencies and Codes:

1209Hz1336Hz1477Hz1633Hz
697Hz123A
770Hz456B
852Hz789C
941Hz*0#D

5.2.12 Dual Watch

The radio features Dual Watch functionality, allowing it to monitor two channels. Press and hold the [A/B] key to switch between Double Wait / Signal Wait / Off dual watch mode. In Double Wait mode, the radio displays and monitors both channels. In Signal Wait mode, it displays both but transmits/receives only on the main channel.

5.2.13 Manual Programming (Channels Memory)

The radio has 640 memory channels. These channels can store receive and transmit frequencies, transmit power, group signaling information, bandwidth, ANI/PTT-ID settings, and a six-character alphanumeric identifier.

Example: Programming a Channel Repeater Offset with CTCSS Tone

  1. Press [EXIT] to switch between menus.
  2. Press [V/M] to set the radio to VFO mode.
  3. [MENU] [5] [MENU] 123.0 [MENU] to select desired TX encode tone (e.g., 123 CTCSS).
  4. [MENU] [1][2] [MENU] [0][5] [0] [0] [MENU] to enter OFFSET frequency (e.g., 5.00MHz).
  5. [MENU] [1][1] [MENU] Plus [MENU] to select offset direction (e.g., plus offset).
  6. Enter RX frequency (e.g., 432.55000 MHz).
  7. [MENU] [1][7] [MENU] [2][8] [MENU] to enter the channel number (e.g., 28).
  8. Press [V/M] to return to MR mode.

5.2.14 Amateur Radio Setup

For typical amateur radio use, the following settings are recommended:

  • Turn off Squelch Tail Elimination (Tail) features (menu item 48).
  • Turn roger beep (ROGER) off (menu item 38).
  • Set bandwidth to Wide (menu item 08).
  • Turn DCS and CTCSS off (menu items 04 through 07).
  • Turn Signaling code off and SQL Mode (menu items 10 and 11).
  • Set and view DTMF ANI, 5TONE ANI, BDC1200 ANI, Radio Name (menu items 61 through 64).

6. Maintenance

6.1 Battery Maintenance

  • Clean accumulated dust on the charging connector regularly with a clean, dry cloth.
  • Charge the battery under 5°C~40°C.
  • Do not dispose of the battery in fire or expose it to direct sunlight/other heat sources.
  • Do not squeeze, penetrate, or remove the housing of the battery.
  • If storing the battery, keep it 80% discharged in a low-temperature, dry environment, away from hot places and direct sunlight.

6.2 General Care

  • Handle the product with care.
  • Do not disassemble, modify, or repair the product or its accessories without authorization.

7. Troubleshooting Guide

PhenomenaAnalysisSolution
You cannot turn on the radio.Battery improperly installed, battery power run out, dirty/damaged battery contacts.Remove and reattach battery, recharge or replace battery, clean battery contacts.
During receiving, the voice is weak or intermittent.Battery voltage low, volume level low, antenna loose/improperly installed, speaker blocked.Recharge battery, increase volume, reattach antenna, clean speaker.
You cannot communicate with other group members.Frequency/signaling type inconsistent, too far from members.Verify TX/RX frequency and signaling type, move closer to members.
You hear unknown voices or noise.Interrupted by radios on same frequency, radio in analog mode with no signaling.Change frequency/adjust squelch level, request dealer to set signaling.
You are unable to hear anyone because of too much noise and hiss.Too far from members, unfavorable position (blocked by buildings), external disturbance.Move to open area, restart radio, stay away from interference sources.
The radio keeps transmitting.VOX turned on or headset not installed correctly.Turn off VOX function, check headset.

NOTE: If these solutions do not resolve your issues, please contact your dealer for technical support.

8. Technical Specifications

General

Channel Capacity640
Channel Spacing25.0 KHz/12.5 KHz
Input Voltage7.4 VDC
Battery Life (5% TX, 5% RX, 90% Standby)Li-on: 15 hours @ 5 watts
Operating Temperature-10°C to 60°C
Antenna Impedance50Ω
Radio Dimensions (LxAxP)64x121x35mm
Radio Weight240g

Transmitter

Frequency Range (TX)144 to 148 MHz, 420 to 450 MHz (America version)
144 to 148 MHz, 430 to 450 MHz (Canadian version)
*144 to 146 MHz, 430 to 440 MHz (EU CE version)
RF Output Power5 Watts Max
Modulation16K0F3E/11K0F3E
Spurious Emission-16 dBm<1GHz, -16 dBm>1GHz
Frequency Stability±2.5 ppm
Audio Distortion≤5%
FM Hum & Noise40 dB

Receiver

Frequency Range108-136, 136-174, 220-260, 350-390, 400 to 520 MHz (Scan Receiver)
*144 to 146 MHz, 430 to 440 MHz (EU CE version)
Sensitivity (12 dB SINAD)-120 dBm
Adjacent Channel Selectivity-60 dBm
Intermodulation and Rejection-70 dBm
Rated Audio Power Output0.75 Watts @ 16 Ω
Rated Audio Distortion≤5%

NOTE: All specifications may be modified without prior notice or liability.

9. User Tips

  • For optimal battery life, ensure the battery is fully charged before first use and cycle it a few times.
  • When using the wireless copy frequency feature, ensure the transmitting radio is close by for best results.
  • Familiarize yourself with the keypad programming options to customize settings without needing a computer.
  • Always check local regulations regarding frequency usage to ensure compliance.
  • Utilize the NOAA weather alert feature for critical weather updates, especially during outdoor activities.

10. Warranty and Support

For technical support or if you encounter any issues not covered in this manual, please contact your dealer. The manufacturer is PO FUNG ELECTRONIC (HK) INTERNATIONAL GROUP COMPANY LIMITED.

For more information, you may visit their websites: www.baofengradio.com or www.pofungshop.com.

A PDF version of the user manual is available online: Download User Manual (PDF).

11. Appendix

For detailed tables on Shortcut Menu operations, DCS Codes, and CTCSS Frequencies, please refer to the full user manual (PDF) available for download.

11.1 Shortcut Menu Operations (Partial List)

MENUName (Full Name)SettingsDescription
01CHL NameCH-1Set the alias of the channel (1 to 16 characters). VFO mode does not have this menu.
02RX Frequency430.00000Displays and allows reset of the current received frequency.
03TX Frequency430.00000Displays and allows reset of the current transmit frequency.
04RX CTCS (Receiver CTCSS)OFF | see CTCSS Table in Appendix DMutes speaker in absence of specific continuous sub-audible signal.
05RX DCS (Receiver DCS)OFF | see DCS Table in Appendix EMutes speaker in absence of specific low-level digital signal.
08BandWidth (Wideband/Narrowband)WIDE | NARRSelects Wideband (25 kHz) or Narrowband (12.5 kHz) bandwidth.
09Trans Power (Transmit Power)HIGH | LOWSelects between HIGH and LOW transmitter power in VFO/Frequency mode.
10SignalingDTMF, 2Tone, 5Tone settingsEdit DTMF/2Tone/5Tone/BDC1200 in PC software. Press PTT to transmit selected ID.
13ScramberOFF | ONEnables/disables Scrambler feature for communication privacy.
29Squelch[0-9]Sets squelch level (0 opens entirely). Sensitivity varies by band.
38ROGEROFF | ROGER 1 | ROGER 2 | ROGER 3Sends an end-of-transmission tone.
41PasswordInput PasswordAllows setting a power-on password for device security.
42Dual WatchOFF | Double Wait | Signal WaitMonitors two channels simultaneously.
49Alarm ModeOn Site | Code+Sound | Code+Sound(No) | Code+ToneSelects type of emergency alert indication. Configured via CPS software.
57AutoLockOFF | ONEnables/disables automatic keypad lock.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.