TNICER Motorcycle Intercom T5/T5PLUS User Manual

1. Introduction

The TNICER T5/T5PLUS Motorcycle Intercom is designed to provide clear audio communication and entertainment for motorcycle riders. This helmet headset features a speaker, microphone, and various mounting options for easy integration into most motorcycle helmets. It supports intercom functionality, allowing for communication while riding.

2. Package Contents

Please verify that all items listed below are included in your package:

• HIFI Speaker with Boom Mic x1
• Soft Tube Microphone x1 (Optional, depending on helmet type)
• 3M Single Sided Silicone Pad x1
• Big Square Velcro x1
• Mounting Bracket x1
• 3M Double Sided Silicone Pad x1
• Round Velcro x2
• Sponge Stickers for Speakers x2
• Metal Clip x1

3. Specifications

4. Setup and Installation

Follow these steps to properly install your TNICER Motorcycle Intercom into your helmet:

1. Prepare Helmet for Speakers

   Locate suitable positions inside your helmet for the speakers, typically near your ears. Use the provided Round Velcro stickers to secure the speakers in place. Ensure they are positioned comfortably and do not obstruct helmet padding.

   

2. Install Microphone

   Choose between the Boom Mic or Soft Tube Microphone based on your helmet type (e.g., full-face vs. open-face). Route the microphone cable discreetly along the helmet's interior. Position the microphone close to your mouth for optimal voice pickup.

   

3. Select and Mount Intercom Unit Base

   Decide whether to use the Mounting Bracket (Metal Clip) or the Double-Sided Tape Base. The Mounting Bracket offers a more secure, semi-permanent attachment, while the Double-Sided Tape Base provides a cleaner look. Attach the chosen base to the side of your helmet where the intercom unit will be easily accessible.

   

   

4. Attach Intercom Unit

   Slide or clip the TNICER intercom unit onto the installed mounting base. Ensure it is firmly secured.

   

5. Connect Cables

   Connect the speaker and microphone cable to the Type-C port on the intercom unit. Ensure the connection is snug.

5. Operating Instructions

This section outlines the basic operation of your TNICER Motorcycle Intercom.

5.1 Power On/Off

• Power On: Press and hold the Power button (usually the largest or most prominent button) for approximately 3 seconds until you hear an audible prompt or see an indicator light.
• Power Off: Press and hold the Power button for approximately 5 seconds until you hear a power-off prompt or the indicator light turns off.

5.2 Bluetooth Pairing (for Phone/GPS)

1. Ensure the intercom is powered off.
2. Press and hold the Power button for about 7 seconds until the indicator light flashes rapidly (e.g., red and blue alternately), indicating pairing mode.
3. On your mobile phone or GPS device, enable Bluetooth and search for new devices.
4. Select "TNICER T5" or "TNICER T5PLUS" from the list of available devices.
5. Once paired, the indicator light will change (e.g., slow blue flashes) and you may hear a confirmation tone.

5.3 Intercom Communication

To initiate or join an intercom conversation with another TNICER intercom unit:

1. Ensure both intercom units are powered on and within range.
2. Press the Intercom button (refer to your device's specific button layout) once to initiate pairing with another unit.
3. The units will attempt to connect. A successful connection will be indicated by a tone or light change.
4. To end an intercom conversation, press the Intercom button again.

5.4 Volume Control

Use the Volume Up (+) and Volume Down (-) buttons to adjust the audio level for music, calls, and intercom conversations.

5.5 Phone Calls

• Answer Call: Press the Multi-function button (often the Power button or a dedicated phone button) once when a call comes in.
• End Call: Press the Multi-function button once during a call.
• Reject Call: Press and hold the Multi-function button for 2 seconds when a call comes in.
• Voice Assistant: Double-press the Multi-function button to activate your phone's voice assistant (Siri, Google Assistant).

6. Maintenance

• Cleaning: Use a soft, damp cloth to wipe the exterior of the intercom unit. Do not use harsh chemicals or abrasive cleaners.
• Storage: When not in use for extended periods, store the device in a cool, dry place away from direct sunlight and extreme temperatures.
• Cable Care: Avoid sharply bending or pulling the cables, especially at connection points, to prevent damage.
• Water Resistance: While designed for outdoor use, avoid submerging the device in water. Ensure the Type-C port cover is securely closed when not charging or connected.

7. Troubleshooting

8. Warranty and Support

Your TNICER Motorcycle Intercom is covered by a manufacturer's warranty against defects in materials and workmanship. For specific warranty terms, duration, and to obtain support, please refer to the documentation provided at the time of purchase or contact the seller directly. Keep your proof of purchase for warranty claims.