ASYPDZSW NHB-108 Pro

Contents

Instruction Manual

ASYPDZSW NHB-108 Pro Stereo Pure Power Amplifier

Model: NHB-108 Pro | Brand: ASYPDZSW

1. Introduction

The ASYPDZSW NHB-108 Pro is a high-end stereo pure power amplifier, featuring a circuit design derived from the renowned Swiss Dartzeel NHB-108. This amplifier is engineered to deliver natural sound with extremely low distortion, providing a rich and smooth audio experience.

Its unique non-large loop feedback amplifier circuit completely eliminates the influence of speaker back electromotive force on the amplifier. The highly acclaimed NHB-108 minimalist broadband circuit features a revolutionary design with strong current output capability and incredible audio quality. There is no global negative feedback, and there is no negative feedback or compensation network in the input and output stages. The unique open-loop design of the output stage.

The sound characteristics are described as smooth, open, natural, and non-noisy, making it ideal for an immersive listening experience. It offers excellent bass volume and depth, attributed to its open-loop feedback amplifier design with top-notch control.

2. Safety Precautions

  • Ensure the amplifier is placed on a stable, level surface with adequate ventilation.
  • Do not block ventilation openings.
  • Keep away from water, moisture, and direct sunlight.
  • Do not open the amplifier casing; refer all servicing to qualified personnel.
  • Ensure correct voltage selection (AC 115V or 230V) before connecting to power.
  • Use appropriate speaker cables and input cables.

3. Setup Guide

3.1 Unpacking and Placement

Carefully remove the amplifier from its packaging. Place it on a sturdy, flat surface, ensuring there is sufficient space around the unit for proper ventilation. Avoid placing it near heat sources or in enclosed cabinets without airflow.

3.2 Voltage Selection

The NHB-108 Pro supports either AC 115V or 230V input voltage. Verify that the voltage selector switch on the rear panel is set to match your local mains voltage before connecting the power cable. Incorrect voltage selection can cause severe damage to the unit.

3.3 Connecting Audio Sources and Speakers

The amplifier features both RCA and XLR inputs, which can be switched freely. Connect your pre-amplifier or audio source to the appropriate input terminals (RCA or XLR) on the rear panel. Ensure all connections are secure.

Connect your speakers to the gold-plated speaker terminals on the rear panel. Pay close attention to polarity (+ to + and - to -) for each channel (R-CH for right channel, L-CH for left channel). Use high-quality speaker cables for optimal performance.

Rear panel of the NHB-108 Pro amplifier showing RCA, XLR inputs, and speaker outputs.
Figure 1: Rear panel connections, illustrating RCA and XLR inputs, and speaker outputs for both channels. The input type can be switched freely.

4. Operating Instructions

4.1 Powering On/Off

After all connections are made and verified, connect the power cable to the amplifier and a suitable wall outlet. Press the 'Power' button on the front panel to turn on the amplifier. The unit will undergo a soft start sequence. To power off, press the 'Power' button again.

4.2 Volume Control and Source Selection

The NHB-108 Pro is a pure power amplifier and does not feature its own volume control or input selection. These functions are handled by your connected pre-amplifier or audio source. Adjust the volume and select your desired input source using your pre-amplifier.

5. Features and Internal Components

The NHB-108 Pro is built with high-quality components to ensure superior audio performance and reliability:

  • Output Transistors: Features 6 pairs of ON High-power sub transistor kings (MJL3281A/MJL1302A) for robust power delivery.
  • Push-Pull Transistors: Equipped with 8 pairs of ON Push tube kings (15032/15033).
  • Filtering Capacitors: Incorporates 12 pieces of Audiophile ELNA 10000uF/63V HIFI grade large filtering capacitors, arranged in a double-sided high current rectifier bridge parallel design.
  • Chassis: Full aluminum chassis customized with CNC machining, featuring a beautiful surface treatment.
  • Power Supply: Adopts dual 400W OFC pure copper transformers, providing completely independent power to each channel. The transformers are shielded with an iron cover.
  • Terminals: High-quality gold-plated RCA and crystal wiring terminals for reliable connections.
  • Protection: Includes Omron independent speaker protection.
  • Soft Start: High current soft start with independent soft start for the two transformers.
Internal view of the NHB-108 Pro amplifier, showing the layout of components including large capacitors and transformers.
Figure 2: Internal view of the amplifier, highlighting the robust power supply and circuit design.
Close-up of ELNA 10000uF/63V audio filter capacitors inside the amplifier.
Figure 3: Large capacity Audiophile ELNA filter capacitors (10000uF/63V X12 PCS).
Close-up of the NHB-108 Pro circuit board with output transistors and optimized design.
Figure 4: NHB-108 circuit board with 6 pairs of output transistors, optimized for 150W-300W output.
Four-panel image showing internal components: Dual OFC transformer, Double rectifier bridge, High current soft start, and Omron independent speaker protection.
Figure 5: Key internal features including dual OFC transformers, double rectifier bridge, soft start mechanism, and Omron speaker protection.

6. Specifications

NHB-108 Pro Amplifier Specifications
FeatureDetail
Input VoltageAC 115V or 230V (selectable)
Output Power (8ohm)150W + 150W
Output Power (4ohm)300W + 300W
Output Effective Value35.1Vrm
Channel Gain26.6dB (21.4x)
Input TypeRCA or XLR (switchable)
Signal to Noise Ratio (SNR)126.4dB
Dynamic Range126.4dB
THD Distortion0.00086%
THD+N Distortion0.005%
Frequency Response Bandwidth± 0.050dB
Input Sensitivity1.66V
Input Impedance22K
Dimensions (W*D*H)430mm * 330mm * 150mm
Package WeightApprox. 21KG
Dimensions diagram of the NHB-108 Pro amplifier.
Figure 6: Amplifier dimensions (Width: 430mm, Depth: 330mm, Height: 150mm).

7. Troubleshooting

  • No Power: Check the power cable connection and ensure the voltage selector switch is correctly set. Verify the wall outlet is functioning.
  • No Sound:
    • Ensure all audio input cables (RCA/XLR) are securely connected to both the amplifier and your pre-amplifier/source.
    • Check speaker cable connections for correct polarity and secure fit.
    • Verify your pre-amplifier/source is powered on and playing audio.
    • Confirm the correct input is selected on your pre-amplifier.
  • Distorted Sound:
    • Check all cable connections for looseness or damage.
    • Ensure the input signal from your pre-amplifier is not overdriving the amplifier.
    • Verify speaker impedance matches the amplifier's capabilities (4-8 ohms).
  • Humming/Buzzing Noise:
    • Ensure all components are properly grounded.
    • Try separating power cables from audio cables to reduce interference.
    • Test with different input cables or sources to isolate the issue.

If you encounter persistent issues, please contact customer support for assistance.

8. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the exterior of the amplifier. Do not use liquid cleaners or aerosols.
  • Ventilation: Ensure the amplifier's ventilation openings are clear of dust and obstructions to prevent overheating.
  • Cable Management: Periodically check all cable connections for tightness and ensure they are not kinked or damaged.
  • Storage: If storing the amplifier for an extended period, disconnect it from power and store it in a dry, dust-free environment.

9. User Tips

  • Pre-amplifier Pairing: As a pure power amplifier, the NHB-108 Pro requires a pre-amplifier for volume control and source selection. Consider pairing it with a high-quality pre-amplifier that complements its natural and low-distortion sound characteristics for the best audio experience.
  • Speaker Matching: For optimal performance, ensure your speakers are well-matched to the amplifier's power output and impedance range (4-8 ohms).
  • Burn-in Period: Like many high-fidelity audio components, the amplifier may benefit from a "burn-in" period of several hours of use to reach its full sonic potential.
  • Color Options: The NHB-108 Pro is available in both black and silver finishes to match your audio setup aesthetics.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

11. Audio Demonstration

Experience the sound quality of the ASYPDZSW NHB-108 Pro amplifier with this audio demonstration video:

Video 1: Audio demonstration of the NHB-108 Pro amplifier in a home audio setup.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.