1. Introduction
The ZGCINE DT-FZ100 (D-Tap) and PD-FZ100 (Type-C) are dummy batteries designed to provide a continuous power supply to your compatible Sony camera. This eliminates the need for frequent battery changes during extended video recording, live streaming, or studio sessions. Featuring an upgraded chip with full decoding capability, these dummy batteries ensure stable performance and high safety levels.

2. Safety Information
This dummy battery is engineered with multiple protection features to safeguard your equipment. Always ensure proper connection and handle the device with care.
- Overvoltage Protection: Prevents damage from excessive input voltage.
- Overcurrent Protection: Protects against current surges.
- Overheat Protection: Monitors and prevents the device from overheating.
- Short Circuit Protection: Automatically cuts off power in case of a short circuit.

3. Setup and Connection
Follow these steps to correctly set up and connect your ZGCINE dummy battery to your camera:
- Identify Your Dummy Battery Type: The ZGCINE dummy battery comes in two main variants: DT-FZ100 (D-Tap connector) and PD-FZ100 (Type-C connector).
- Connect the Power Source:
- For DT-FZ100 (D-Tap): Connect the D-Tap male head to a compatible D-Tap power source (e.g., V-mount battery, Gold-mount battery). The D-Tap male head supports 180° rotation for flexible and stable connection.
- For PD-FZ100 (Type-C): Connect the Type-C connector to a compatible USB-C power source that meets the input voltage requirements.
- Observe the Indicator Light (D-Tap only): The D-Tap male head is equipped with an anti-reverse insertion indicator light. A flashing red light indicates an incorrect insertion, and the power will be cut off automatically. A steady green light indicates a correct connection.
- Insert Dummy Battery into Camera: Carefully insert the NP-FZ100 dummy battery end into your Sony camera's battery compartment, ensuring it clicks securely into place.
- Power On: Once connected, power on your camera. It should now receive continuous power from your external source.




4. Operating Instructions
Once the dummy battery is correctly installed and connected to a power source, your camera will operate as if it has a fully charged NP-FZ100 battery. There are no special operating procedures required beyond normal camera usage.
- Ensure your external power source is adequately charged or connected to mains power for uninterrupted operation.
- Monitor your camera's battery indicator, which will typically show full charge when using the dummy battery.
- Disconnect the power source and remove the dummy battery when not in use.
5. Maintenance
To ensure the longevity and optimal performance of your ZGCINE dummy battery, follow these maintenance guidelines:
- Keep the dummy battery and connectors clean and free from dust and debris.
- Store the device in a cool, dry place when not in use.
- Avoid exposing the device to extreme temperatures or moisture.
- Do not attempt to disassemble or modify the dummy battery, as this will void the warranty and could cause damage.
- Regularly inspect the cable for any signs of wear or damage.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Camera not powering on. | No power from external source, incorrect connection, or dummy battery not fully inserted. | Check external power source. Ensure D-Tap/Type-C connector is securely attached. Re-insert dummy battery into camera until it clicks. |
| D-Tap indicator light is flashing red. | Incorrect D-Tap connection (reverse polarity). | Disconnect and re-connect the D-Tap plug, ensuring correct orientation. The light should turn steady green. |
| Camera displays an error message. | Power supply issue or compatibility problem. | Verify the external power source meets the required specifications. Ensure your camera model is listed as compatible. |
| Dummy battery or cable feels hot. | Overload or internal issue. | Immediately disconnect power. Allow to cool. If problem persists, discontinue use. |
7. Specifications
| Feature | DT-FZ100 (D-Tap) | PD-FZ100 (Type-C) |
|---|---|---|
| Brand Name | ZGCINE | |
| Photography Accessories Type | Battery charger / Power Adapter | |
| Input Voltage | 12V - 17V | 9V - 12V (PD IN: 9V/3A) |
| Output Voltage | 8V (Regulated) / 8.4V | |
| Output Current | 2A | 3A |
| Cable Length | 60cm | |
| Electronic | No | |
| Package | Yes | |
| Origin | Mainland China | |
| High-concerned chemical | None | |
Compatible Camera Models:

- Sony A7R V
- Sony A7 IV
- Sony A7S III
- Sony A7R IV
- Sony A7R III
- Sony A7 III
- Sony A7C
- Sony A7CR
- Sony A6600
- Sony A6700
- Sony FX3
- Sony FX30
- Sony ZV-E1
- Sony A9
- Sony A9II
8. User Tips
- Always ensure your external power source provides stable voltage within the specified input range to prevent damage to your camera.
- For D-Tap connections, pay attention to the indicator light to confirm correct polarity before powering on your camera.
- When using the Type-C variant, ensure your power adapter supports the required Power Delivery (PD) profile for optimal performance.
9. Warranty and Support
For warranty information, technical support, or service inquiries, please contact the manufacturer or your point of purchase. Keep your purchase receipt as proof of purchase.
User manual (PDF) available for download: ZGCINE NP-FZ100 Dummy Battery User Manual