LIZAO MT6826S

Contents

LIZAO MT6826S High-Precision Magnetic Encoder Module

User Manual

1. Introduction

The LIZAO MT6826S is a high-precision, high-speed magnetic encoder module designed for accurate angle measurement. It is based on MagnTek's latest fourth-generation magnetic angle encoder IC family, utilizing anisotropic magnetoresistance (AMR) technology and proprietary signal processing. This module provides absolute angle measurement from 0° to 360°.

The MT6826S chip integrates a pair of AMR Wheatstone bridges and signal processing ASIC circuits. As the magnetic field parallel to the chip surface rotates, the module outputs various angle signals, including ABZ, UVW, and PWM. It boasts a system delay of less than 2 microseconds and can support speeds up to 120,000 revolutions per minute. To ensure high accuracy, the MT6826S features a simple client self-calibration function, achieving an angle accuracy of <±0.07° after calibration.

LIZAO MT6826S Magnetic Encoder Module with pin headers and magnet
Figure 1: LIZAO MT6826S Magnetic Encoder Module with included components.

2. Specifications

FeatureSpecification
Model NumberMT6826S
Brand NameLIZAO
Angle Measurement Range0° to 360° (Absolute)
Working Voltage3.3V - 5.0V
Operating Temperature-40°C to 125°C
System Delay< 2 microseconds
Maximum Speed120,000 revolutions per minute
Incremental Output (ABZ)1 to 1024 lines resolution
Commutation Output (UVW)1 to 16 polarity support
Other OutputsPWM
Angle Accuracy (after calibration)< ±0.07°
Dimensions (L x W x H)33mm x 33mm x 2mm
Weight3g
Package TypeSMD
Typical ApplicationsIndustrial sewing machines, closed-loop stepper motors
Detailed specifications and pinout diagram for MT6826S
Figure 2: Detailed specifications and pinout diagram.
MT6826S module with dimensions 33mm x 33mm
Figure 3: Module dimensions.

3. Key Features

  • High Precision: Achieves an angle accuracy of <±0.07° after calibration.
  • High Speed: Supports rotational speeds up to 120,000 RPM.
  • Absolute Angle Measurement: Provides 0° to 360° absolute angle data using AMR technology.
  • Low System Delay: Fast response with a system delay of less than 2 microseconds.
  • Multiple Output Interfaces: Offers ABZ (incremental), UVW (commutation), and PWM outputs.
  • Self-Calibration Function: Simple client-side calibration to overcome accuracy loss from magnets and installation.
  • Wide Operating Temperature Range: Functions reliably from -40°C to 125°C.
  • Compact Design: Small form factor (33mm x 33mm x 2mm) for integration into various projects.

4. Package Contents

The MT6826S magnetic encoder module package typically includes:

  • 1x MT6826S Magnetic Encoder Module
  • 1x Small Cylindrical Magnet
  • 3x Pin Headers (e.g., 6-pin straight headers)
MT6826S module with magnet and pin headers
Figure 4: MT6826S module and included accessories.

5. Setup and Connection

Follow these steps to set up and connect your MT6826S module:

5.1. Pinout Description

Refer to the pinout diagram for correct connections:

Pin NameDescription
VDDPower Supply (3.3V - 5.0V)
GNDGround
MISOSPI Master In, Slave Out
MOSISPI Master Out, Slave In
SCKSPI Serial Clock
CSNSPI Chip Select (Active Low)
CAL_ENCalibration Enable Pin
A, B, ZIncremental Encoder Outputs
U, V, WCommutation Outputs
PWMPulse Width Modulation Output

5.2. Electrical Connection

  1. Connect the VDD pin to your power supply (3.3V to 5.0V).
  2. Connect all GND pins to the system ground.
  3. Connect the SPI pins (MISO, MOSI, SCK, CSN) to your microcontroller's SPI interface if you plan to use SPI for angle data retrieval or configuration.
  4. Connect the A, B, Z pins to your system if you require incremental encoder outputs.
  5. Connect the U, V, W pins for motor commutation applications.
  6. Connect the PWM pin if you intend to use the PWM angle output.

5.3. Magnet Placement

The performance of the magnetic encoder heavily relies on the correct placement of the magnet. The provided cylindrical magnet should be placed centrally above or below the MT6826S sensor chip. Ensure the magnet is aligned coaxially with the sensor for optimal magnetic field detection and accurate angle measurement.

5.4. Initial Calibration

The MT6826S features a self-calibration function to compensate for magnet and installation inaccuracies. Consult the MT6826S datasheet (not provided here) for detailed instructions on how to trigger and complete the calibration process using the CAL_EN pin or via SPI commands. Proper calibration is crucial for achieving the specified angle accuracy.

6. Operation

Once the module is correctly connected and calibrated, you can begin reading angle data:

  1. SPI Interface: For the most detailed and accurate angle data, use the SPI interface. Your microcontroller can read the absolute angle value directly from the MT6826S registers. This interface also allows for configuration of various parameters.
  2. ABZ Outputs: The A, B, and Z pins provide standard incremental encoder signals. A and B are quadrature signals, and Z is the index pulse (once per revolution). These are suitable for applications requiring relative position tracking.
  3. UVW Outputs: The U, V, and W pins provide commutation signals, typically used for controlling brushless DC (BLDC) motors.
  4. PWM Output: The PWM pin outputs a pulse width modulated signal where the duty cycle or pulse width is proportional to the measured angle.

The MT6826S is designed for high-speed applications, capable of tracking rotations up to 120,000 RPM with minimal delay.

7. Maintenance

The MT6826S magnetic encoder module is a robust electronic component, but proper care ensures its longevity and reliable performance:

  • Keep Dry: Avoid exposure to moisture or liquids, which can damage the electronic components.
  • Temperature Control: Operate within the specified temperature range of -40°C to 125°C. Extreme temperatures outside this range can affect performance or cause permanent damage.
  • Handle with Care: Avoid physical shock or excessive force, especially to the sensor area and pin connections.
  • Cleanliness: Keep the module free from dust and debris. Use a soft, dry brush or compressed air for cleaning if necessary. Do not use harsh chemicals.
  • Magnet Care: Ensure the magnet remains clean and free of ferromagnetic particles that could interfere with its magnetic field.

8. Troubleshooting

If you encounter issues with your MT6826S module, consider the following:

  • No Output/Incorrect Readings:
    • Verify power supply (VDD) and ground (GND) connections are correct and stable (3.3V-5.0V).
    • Check all signal line connections (SPI, ABZ, UVW, PWM) for continuity and correct wiring.
    • Ensure the magnet is correctly positioned and aligned with the sensor. The distance between the magnet and the sensor is critical.
    • Perform the self-calibration procedure as described in the datasheet.
  • Inconsistent or Jittery Readings:
    • Check for sources of electromagnetic interference (EMI) near the module.
    • Ensure the power supply is clean and free of noise. Add decoupling capacitors if necessary.
    • Re-check magnet stability and ensure it's not vibrating or moving relative to the sensor.
  • Module Not Responding via SPI:
    • Verify SPI clock speed and mode settings on your microcontroller match the MT6826S requirements.
    • Ensure the CSN pin is correctly toggled for each SPI transaction.

9. Warranty and Support

For specific warranty information, please refer to the terms and conditions provided by your retailer or the manufacturer at the time of purchase. General support and technical documentation, including detailed datasheets and application notes, may be available from the manufacturer's website or through authorized distributors.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.