LUCKY Wireless Sonar Sensor (D/D+T)

Contents

LUCKY Wireless Sonar Sensor User Manual

Model: Wireless Sonar Sensor (D/D+T)

Brand: LUCKY

1. Introduction

This manual provides comprehensive instructions for the LUCKY Wireless Sonar Sensor, designed to work seamlessly with compatible LUCKY fish finders such as the FFW718 and FF518. This sensor is an essential tool for anglers, providing accurate data on water depth and fish location. Please read this manual thoroughly before using the device to ensure proper operation and longevity.

2. Product Overview

The LUCKY Wireless Sonar Sensor is a compact and durable device that transmits sonar data wirelessly to your fish finder unit. It is available in two main models: 'D' (Depth) and 'D+T' (Depth and Temperature), offering different functionalities.

Diagram of the D+T Wireless Sonar Sensor with labeled parts: Seal cover, Seal ring, Battery place, Sonar detection, and Hole tied to fishing line.
Figure 2.1: D+T Wireless Sonar Sensor Components

This image shows the key components of the D+T sensor, including the seal cover, seal ring, battery compartment, sonar detection area, and the hole for attaching a fishing line.

Diagram of the D Wireless Sonar Sensor with labeled parts: Seal Cover, Seal Ring, Battery Place, Sonar Detection, and Hole tied to fishing line.
Figure 2.2: D Wireless Sonar Sensor Components

This image illustrates the components of the D sensor, highlighting the seal cover, seal ring, battery place, sonar detection, and the attachment point for a fishing line.

3. Setup and Installation

  1. Battery Installation:

    The sensor runs on a replaceable CR2032 battery. To install or replace the battery:

    • Unscrew the seal cover on the top of the sensor.
    • Carefully remove the old battery (if any) and insert a new CR2032 battery, ensuring correct polarity.
    • Replace the seal ring properly to ensure a watertight seal.
    • Screw the seal cover down tightly to prevent water ingress. A warning label on the sensor reminds users to screw down the cover to prevent water.
    Top-down view of the D+T sensor showing the screw-down cover with a warning label: 'Warning: please screw down cover to prevent water.'
    Figure 3.1: Sensor Top View with Watertight Seal Warning

    This image highlights the importance of securely screwing down the seal cover to maintain the sensor's watertight integrity.

  2. Compatibility Check:

    Ensure your fish finder is compatible with the sensor model. The D+T transducer is suitable for most LUCKY fish finders, including models like FFW718 and FF518. The D transducer is designed for basic fish finders such as FFW1108-1 and FFCW1108-1.

    Image showing the D+T sensor alongside various compatible LUCKY fish finder models like FFW718 and FF518.
    Figure 3.2: Compatible Fish Finder Models

    This image displays the D+T sensor and several LUCKY fish finder units it is compatible with, such as FFW718 and FF518.

  3. Deployment:

    The sensor features special holes designed for tying your fishing line. Attach a sturdy fishing line to these holes to allow for easy casting and retrieval of the sensor into the water.

4. Operating Instructions

  1. Power On:

    Once the battery is installed and the cover is sealed, the sensor will automatically activate when it comes into contact with water. Ensure your compatible fish finder unit is also powered on and ready to receive signals.

  2. Casting and Retrieval:

    Cast the sensor into the desired fishing area using the attached fishing line. The sensor is designed to float on the water surface, with its sonar transducer submerged.

    The D+T Wireless Sonar Sensor floating on the water surface.
    Figure 4.1: Sensor Floating in Water

    This image shows the D+T sensor correctly floating on the water, ready for operation.

  3. Sonar Detection:

    The sensor utilizes a 125KHz sonar frequency with a 90-degree beam angle to detect water depth and fish. It can detect depths up to 45 meters (147 feet). The data is then wirelessly transmitted to your fish finder display.

    Diagram illustrating the 90-degree wide detection sonar cone of the sensor, showing a maximum water depth of 45 meters and a 125KHz frequency.
    Figure 4.2: Sonar Detection Pattern

    This diagram visually represents the sensor's 90-degree wide detection cone, its maximum depth capability of 45 meters, and the 125KHz sonar frequency.

  4. Temperature Reading (D+T Model Only):

    If you have the D+T model, the sensor will also transmit water temperature data to your compatible fish finder.

5. Maintenance

  • Cleaning:

    After each use, rinse the sensor with fresh water to remove any salt, dirt, or debris. Wipe it dry with a soft cloth. Do not use abrasive cleaners or solvents.

  • Battery Replacement:

    Replace the CR2032 battery when the performance of the sensor degrades or when indicated by your fish finder unit. Always ensure the seal cover and seal ring are correctly re-installed and tightened to maintain waterproofing.

  • Storage:

    Store the sensor in a cool, dry place away from direct sunlight and extreme temperatures. If storing for an extended period, it is recommended to remove the battery.

6. Troubleshooting

Problem Possible Cause Solution
No signal or poor signal reception on fish finder.
  • Low or dead battery in sensor.
  • Sensor not properly submerged or too far from fish finder.
  • Water ingress due to loose seal cover.
  • Incompatible fish finder unit.
  • Replace CR2032 battery.
  • Ensure sensor is floating correctly and within range of the fish finder.
  • Check seal cover and seal ring; tighten securely.
  • Verify fish finder model compatibility (e.g., FFW718, FF518 for D+T model).
Sensor not activating in water.
  • Dead battery.
  • Poor contact with water (e.g., sensor not fully submerged).
  • Replace CR2032 battery.
  • Ensure the sensor's bottom contacts are fully in water.
Inaccurate depth or temperature readings.
  • Obstructions near the sensor.
  • Turbulent water conditions.
  • Sensor malfunction.
  • Relocate the sensor to a clearer area.
  • Use in calmer water if possible.
  • Contact support if issues persist.

7. Specifications

Feature Specification
Material Plastic
Models Available D (Depth), D+T (Depth and Temperature)
Depth Range 45 meters (147 feet)
Beam Angle 90 degrees
Sonar Frequency 125 KHz
Power Source 1 x CR2032 battery
Dimensions 7.8 cm * 5.5 cm (3.1 in * 2.2 in)
Weight 45 grams (1.6 oz)

8. User Tips

  • Always double-check the compatibility of your fish finder model with the sonar sensor (D or D+T) before purchase and use.
  • Ensure the battery compartment is securely sealed after battery installation or replacement to prevent water damage, which is the most common issue.
  • For optimal performance, use a fresh CR2032 battery and replace it regularly, especially if you notice a decrease in signal strength or range.
  • When casting, ensure the sensor lands smoothly on the water surface to avoid potential damage and ensure immediate activation.

9. Warranty and Support

For warranty information, please refer to the documentation provided at the time of purchase or contact the seller directly. If you encounter any issues or require technical assistance, please reach out to the "Cycling Outdoor Sportswear & Accessories Store" (seller) through the platform where you made your purchase. Provide your order details and a clear description of the problem for efficient support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.