1. Introduction
The PowMr WIFI-HF-N module is designed for remote monitoring of solar PV systems. It collects operating data and power generation information from your inverter, transmitting it to a cloud platform (SOLARMAN Portal) via Ethernet. This allows for long-term, efficient monitoring, real-time status display, historical data analysis through graphs, and immediate alerts for any malfunctions via SMS and email. This module significantly simplifies PV system management and maintenance.


2. Setup
2.1. Physical Connection
- Ensure your inverter is powered off before making any connections.
- Locate the RS485 communication port on your PowMr solar inverter.
- Connect the provided adapter cable from the WIFI module to the inverter's RS485 port. Ensure a secure connection.
- The module can be mounted using the fixed trestle provided.

2.2. Interface Identification and Wiring
The module uses a 4-pin connector for communication and power. Refer to the diagram below for pin assignments:

Detailed wiring for the adapter cable:

2.3. Network Configuration
The module can be configured via local web interface, remote server, or Bluetooth. For remote monitoring, ensure the module is connected to your local network (router) via Ethernet.
- Domain Name: access1.solarmanpv.com (SOLARMAN 3.0)
- IP: 47.102.152.71 (SOLARMAN 3.0)
- Port No.: 10000 (SOLARMAN 3.0)
Refer to the SOLARMAN Portal documentation for detailed instructions on adding your device and configuring monitoring settings.
3. Operating
3.1. LED Indicator Lights
After connecting the logger to the inverter and powering it on, check the status of the NET, COM, and READY lights to confirm proper operation.

| Light | Implication | Status |
|---|---|---|
| NET | Communicate with base station (router) | Light off: Connection to the router failed. |
| On 1s/Off 1s (Slow flash): Connection to the router succeeded. | ||
| Light on: Connection to the server succeeded. | ||
| On 100ms/Off 100ms (Fast flash): Fast networking. | ||
| COM | Communicate with inverter | Light on: Logger connected to the inverter. |
| Light off: Connection to the inverter failed. | ||
| On 1s/Off 1s (Slow flash): Logger communicating with inverter. | ||
| READY | Logger Running Status | Light off: Logger runs abnormally. |
| On 1s/Off 1s (Slow flash): Logger runs normally. | ||
| On 100ms/Off 100ms (Fast flash): Restore factory settings. |
3.2. Monitoring Platform
Once the module is successfully connected and configured, you can access your PV system's data through the SOLARMAN Portal. This platform provides real-time data, historical performance graphs, and allows you to manage alerts and settings.
4. Maintenance
- Cleaning: Keep the module clean and free from dust. Use a soft, dry cloth for cleaning.
- Ventilation: Ensure the module is installed in a location with adequate airflow to prevent overheating.
- Firmware Upgrades: Firmware can be updated via local web upgrade or remote update. Regularly check for available firmware updates to ensure optimal performance and security.
5. Troubleshooting
If data on the monitoring platform is abnormal or the module is not functioning as expected, refer to the table below for common issues and solutions. Always check LED indicators first.
| NET | COM | READY | Fault Description | Fault Cause | Solution |
|---|---|---|---|---|---|
| Any status | OFF | Slow flash | Communicate with inverter abnormal | 1. Connection between stick logger and inverter loose. 2. Inverter does not match with stick logger's communication rate. | 1. Check the connection between stick logger and inverter. Remove and reinstall. 2. Check inverter's communication rate for compatibility. |
| OFF | ON | Slow flash | Communicate with router abnormal | 1. Stick logger does not have a network. 2. Antenna abnormal. 3. Router WiFi signal strength weak. | 1. Check if the wireless network is configured. 2. Check the antenna for damage or looseness. 3. Enhance Router WiFi signal strength. |
| Slow flash | ON | Slow flash | Communicate with router normal, communicate with remote server abnormal | 1. Router networking abnormal. 2. Server direction has been verified. 3. Network restrained. | 1. Check if the router has a network. 2. Check router setup. 3. Contact Customer Service. |
| OFF | OFF | OFF | Power supply abnormal | 1. Connection between stick logger and inverter loose or abnormal. 2. Inverter power insufficient. 3. Stick Logger abnormal. | 1. Check the connection, remove the stick logger and install again. 2. Check inverter output power. 3. Contact Customer Service. |
If the issue persists after following these steps, please contact customer service.
6. Specifications

6.1. Wireless Parameters
- Working Frequency: 2.412GHz~2.472GHz
- Transmit Power: 802.11b: +17 dBm±1.5dBm (@11Mbps), 802.11g: +15 dBm±1.5dBm (@54Mbps), 802.11n: +14 dBm±1.5dBm (@HT20, MCS7)
- Antenna Option: Embedded PCB antenna
6.2. Bluetooth
- Wireless Standard: BLE5.0
- Frequency Range: 2.402GHz-2.480GHz
- Transmit Power: MAX15dBm
6.3. Hardware Parameters
- Data Interface: RS485
- Working Voltage: DC5V~DC12V
- Working Power: 1.5W
- Indicator Lights: One connected to Inverter, One connected to router, One connected to heartbeat
- Data Storage: Default: 8 MBYTE FLASH
- Working Temperature: -30℃~+70℃
- Working Humidity: 10%-90%, no condensation
- Storage Temperature: -45℃~+90℃
- Storage Humidity: <40%
- External Interface: Small Aviation Head
- No. of Connections: One
6.4. Software Parameters
- Serial Communication Rate: Default: 9600bps (1200-115200bps optional)
- Data Transmission Interval: Default: 5 mins (1-15 mins optional)
- Configuration: AT+Instruction set, Local web configuration, Remote server, Bluetooth
- Firmware Upgrade: Local web upgrade, Remote update
- Others: Real-time Control, Data Resuming
6.5. Product Size
Dimensions (Unit: mm, Accuracy: ±2%):
- Length: 127.50 mm
- Width: 46.12 mm
- Thickness: 27.12 mm
7. User Tips
- Check Compatibility: Always verify that this WIFI module is compatible with your specific inverter model before purchase. Incompatibility is a common reason for non-functionality.
- Secure Connections: Ensure all physical connections (RS485 cable, Ethernet) are firm and correctly seated to prevent communication issues.
- Router Settings: If experiencing network issues, check your router's settings, Wi-Fi signal strength, and ensure it's providing network access to the module.
- LED Indicators: Familiarize yourself with the LED indicator meanings. They are your first diagnostic tool for any operational problems.
8. Warranty and Support
For warranty information, technical support, or further assistance, please contact your seller or the manufacturer directly. Keep your purchase records handy when seeking support.
A comprehensive user manual in PDF format may be available for download from the manufacturer's website or via the following link: View PDF Manual