NJTY 88N

Contents

NJTY 88N Analog Multimeter User Manual

Model: 88N

1. Introduction

The NJTY 88N is a high-precision analog multimeter designed for a wide range of electrical measurements. Featuring an external magnetic pointer, anti-burn protection, and a self-resetting fuse design, this universal meter offers reliable performance for AC/DC voltage, current, resistance, capacitance, diode, transistor, frequency, and continuity testing. Its robust construction includes a soft rubber protective cover for durability and a magnetic back for convenient placement.

NJTY 88N Multimeter with key features listed: High-precision analog multimeter, AC/DC voltage testing, Resistance and diode testing, Capacitance and transistor testing, AC/DC current testing, Self-resetting fuse design, Optional carrying case.
Figure 1: NJTY 88N Multimeter highlighting its core features and capabilities.
NJTY 88N Multimeter highlighting test capabilities: AC/DC Voltage 2500V Test, Frequency and Continuity Buzzer Test, Capacitance 1000uF Test, Diode and Transistor Test, AC/DC Current 10A Test.
Figure 2: Overview of the NJTY 88N Multimeter's comprehensive testing functions.

2. Safety Information

Please read and understand all safety instructions before operating the multimeter. Failure to follow these instructions may result in electric shock, fire, or damage to the instrument.

  • Always ensure the multimeter is in good working condition before use.
  • Do not attempt to measure voltages or currents exceeding the specified maximum ratings.
  • Use caution when working with live circuits. Always assume circuits are live until proven otherwise.
  • Ensure the test leads are properly connected to the correct input jacks for the desired measurement.
  • Never touch the metal tips of the test leads when connected to a circuit.
  • Replace batteries and fuses only with the specified types and ratings.
  • Do not operate the multimeter in wet environments or if your hands are wet.
  • Disconnect the test leads from the circuit and turn off the multimeter before changing functions or ranges.

3. Product Overview

The NJTY 88N multimeter features a clear analog display and a robust design for reliable measurements.

3.1 Components and Display

Detailed front view of the NJTY 88N Multimeter with labeled components: Zero adjustment knob, Resistance zero adjustment, 2500V High voltage jack, AC Current 10A jack, DC Current 10A jack, Soft rubber sleeve, Transistor jack, Function knob / Range, Positive test jack, Common jack, Meter hanging hole with magnet, Clear dial with no ghosting.
Figure 3: Front panel and component identification of the NJTY 88N Multimeter.
  • Analog Display: Clear dial with an external magnetic pointer for precise readings.
  • Function/Range Knob: Used to select the desired measurement function and range.
  • Zero Adjustment Knob: For fine-tuning the pointer to zero before resistance measurements.
  • Resistance Zero Adjustment: Specific adjustment for resistance ranges.
  • Input Jacks:
    • 2500V High Voltage Jack: For high voltage measurements.
    • AC Current 10A Jack: For AC current measurements up to 10A.
    • DC Current 10A Jack: For DC current measurements up to 10A.
    • Positive Test Jack: Red test lead connection.
    • Common Jack (COM): Black test lead connection.
  • Transistor Jack: For testing transistors (hFE).
  • Soft Rubber Protective Cover: Provides anti-slip and drop resistance.
  • Magnetic Back: Allows the instrument to attach to iron objects for hands-free operation.
NJTY 88N Multimeter with its soft rubber protective cover.
Figure 4: The multimeter equipped with its soft rubber protective cover.
Back view of the multimeter showing the magnetic stand.
Figure 5: The magnetic back of the multimeter for convenient attachment.

4. Setup

4.1 Unpacking

Upon receiving your NJTY 88N Multimeter, carefully unpack all components. The package should include:

  • NJTY 88N Analog Multimeter
  • Test Leads (Red and Black)
  • User Manual
  • Spare Fuses (two, typically located in the battery compartment)
NJTY 88N Multimeter with included accessories: manual, test leads, and two spare fuses.
Figure 6: Multimeter and its standard accessories.

4.2 Battery Installation

The multimeter requires 2 AAA batteries (not included). To install or replace batteries:

  1. Ensure the multimeter is turned OFF and test leads are disconnected.
  2. Locate the battery compartment on the back of the unit.
  3. Open the battery compartment cover.
  4. Insert 2 AAA batteries, observing the correct polarity (+/-).
  5. Close the battery compartment cover securely.

Note: Two spare fuses are typically installed in the battery compartment for future replacement.

4.3 Test Lead Connection

Connect the test leads to the appropriate input jacks based on the measurement you intend to perform:

  • Always connect the black test lead to the COM (Common) jack.
  • Connect the red test lead to the Positive Test Jack for most voltage, resistance, capacitance, and frequency measurements.
  • For AC/DC current measurements up to 10A, connect the red test lead to the dedicated AC Current 10A Jack or DC Current 10A Jack.
  • For high voltage measurements, use the 2500V High Voltage Jack with the red test lead.

5. Operating Instructions

The NJTY 88N is a manual range multimeter. Always select the appropriate function and range before making a measurement.

5.1 AC/DC Voltage Testing

  1. Connect the black test lead to the COM jack and the red test lead to the Positive Test Jack.
  2. Set the function knob to the desired ACV (AC Voltage) or DCV (DC Voltage) range. Start with the highest range if the voltage is unknown.
  3. Connect the test probes across the component or circuit to be measured.
  4. Read the voltage value from the analog display.
Multimeter performing AC voltage testing.
Figure 7: Example of AC voltage testing.
Multimeter performing DC voltage testing with a 9V battery.
Figure 8: Example of DC voltage testing.

5.2 AC/DC Current Testing

CAUTION: Never connect the multimeter in parallel with a voltage source when measuring current, as this can damage the instrument and the circuit.

  1. Connect the black test lead to the COM jack.
  2. Connect the red test lead to the appropriate AC Current 10A Jack or DC Current 10A Jack.
  3. Set the function knob to the desired ACA (AC Current) or DCA (DC Current) range. Start with the highest range if the current is unknown.
  4. Break the circuit and connect the multimeter in series with the load.
  5. Read the current value from the analog display.
Multimeter performing AC current measurement.
Figure 9: Example of AC current measurement.

5.3 Resistance Testing

  1. Connect the black test lead to the COM jack and the red test lead to the Positive Test Jack.
  2. Set the function knob to the desired Ohm (Ω) range.
  3. Before measuring, short the test leads together and use the Zero Adjustment Knob to set the pointer to zero.
  4. Connect the test probes across the resistor or component to be measured (ensure the circuit is de-energized).
  5. Read the resistance value from the analog display.
Multimeter performing resistance testing.
Figure 10: Example of resistance testing.

5.4 Capacitance Testing

  1. Connect the black test lead to the COM jack and the red test lead to the Positive Test Jack.
  2. Set the function knob to the desired Capacitance (C) range.
  3. Discharge the capacitor before testing.
  4. Connect the test probes across the capacitor.
  5. Read the capacitance value from the analog display.
Multimeter performing capacitance testing with a capacitor. The measurement is of capacitance value, not an assessment of its condition.
Figure 11: Example of capacitance testing. Note that this measures capacitance value, not necessarily the capacitor's health.

5.5 Diode Testing

  1. Connect the black test lead to the COM jack and the red test lead to the Positive Test Jack.
  2. Set the function knob to the Diode (symbol) range.
  3. Connect the test probes across the diode.
  4. Observe the reading for forward and reverse bias to determine diode functionality.
Multimeter performing diode testing.
Figure 12: Example of diode testing.

5.6 Transistor Testing (hFE)

  1. Set the function knob to the hFE range.
  2. Identify the type of transistor (NPN or PNP) and its emitter, base, and collector leads.
  3. Insert the transistor leads into the corresponding holes in the Transistor Jack.
  4. Read the hFE (DC current gain) value from the display.
Multimeter performing transistor testing.
Figure 13: Example of transistor testing.

5.7 Frequency Testing

  1. Connect the black test lead to the COM jack and the red test lead to the Positive Test Jack.
  2. Set the function knob to the Frequency (Hz) range.
  3. Connect the test probes across the signal source.
  4. Read the frequency value from the analog display.
Multimeter performing frequency testing.
Figure 14: Example of frequency testing.

5.8 Continuity Buzzer Test

  1. Connect the black test lead to the COM jack and the red test lead to the Positive Test Jack.
  2. Set the function knob to the Continuity (buzzer symbol) range.
  3. Connect the test probes across the circuit or component.
  4. A continuous beep indicates a low-resistance path (continuity).
Multimeter performing continuity buzzer test.
Figure 15: Example of continuity testing.

5.9 LED Testing

  1. Connect the black test lead to the COM jack and the red test lead to the Positive Test Jack.
  2. Set the function knob to the LED test range (if available, often combined with diode test).
  3. Connect the test probes across the LED, observing polarity.
  4. A lit LED or a specific reading indicates functionality.
Multimeter performing LED testing.
Figure 16: Example of LED testing.

6. Maintenance

6.1 Cleaning

Wipe the multimeter casing with a damp cloth. Do not use abrasive cleaners or solvents. Ensure the device is dry before storage or use.

6.2 Fuse Replacement

The NJTY 88N features a self-resetting fuse design for enhanced safety. However, in case of severe overload, a fuse might still blow. Two spare fuses are typically provided in the battery compartment.

  1. Ensure the multimeter is turned OFF and test leads are disconnected.
  2. Open the battery compartment cover.
  3. Carefully remove the old fuse.
  4. Insert a new fuse of the correct type and rating (refer to specifications).
  5. Close the battery compartment cover securely.
Internal view of the multimeter showing the circuit board with self-resetting fuse design.
Figure 17: Internal view showing the circuit board and self-resetting fuse design.

6.3 Storage

When not in use for extended periods, remove the batteries to prevent leakage. Store the multimeter in a cool, dry place, away from direct sunlight and extreme temperatures.

7. Troubleshooting

  • No Display/Power: Check battery installation and ensure batteries are not depleted. Replace if necessary.
  • Incorrect Readings:
    • Ensure test leads are correctly connected to the appropriate jacks.
    • Verify the function and range knob is set correctly for the measurement.
    • For resistance, ensure the meter is zeroed before measurement.
    • Check if the circuit is de-energized for resistance or capacitance measurements.
  • No Continuity Beep: Ensure the continuity function is selected and test leads are making good contact.
  • Meter Not Responding: If the meter becomes unresponsive, turn it off, remove batteries, wait a few seconds, then reinsert batteries and restart.

8. Specifications

The following table details the technical specifications of the NJTY 88N Analog Multimeter:

Specifications table for NJTY 88N Multimeter.
Figure 18: Detailed specifications of the NJTY 88N Multimeter.
Feature Specification
Model 88N
DC Current 50uA-500mA-10A (±5%)
AC Current 50mA-500mA-10A (±5%)
AC Voltage 250mV-2.5V-10V-50V-250V-500V-1000V-2500V (±5%)
DC Voltage 250mV-2.5V-10V-50V-250V-500V-1000V-2500V (±5%)
Resistance R×1R×10R×100R×1KR×10KR×100K (±10%)
Capacitance ×1/×10/×100 (1000uF)
Frequency ×1/×10/×100 (10kHz)
Continuity Buzzer Yes
Transistor Yes
Diode Yes
Circuit Board Double-sided gold-plated circuit board
Meter Head External magnet
Power Supply AAA*2 batteries
Weight About 500g
Dimensions 179*118*50 (mm)
Multimeter with dimensions labeled: 179mm, 118mm, 50mm.
Figure 19: Physical dimensions of the NJTY 88N Multimeter.

9. User Tips

  • Always Start High: When measuring unknown voltages or currents, always start with the highest range setting and work your way down to avoid overloading the meter.
  • Zero Resistance: Remember to short the test leads and adjust the zero knob before taking resistance measurements for accuracy.
  • Capacitor Discharge: Always discharge capacitors before testing them to prevent damage to the meter or injury.
  • Magnetic Convenience: Utilize the magnetic back to attach the multimeter to metal surfaces, freeing up your hands for testing.
  • Protective Cover: Keep the soft rubber protective cover on the multimeter to guard against accidental drops and impacts.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.