1. Introduction
The NOKLEAD Model 5253 is a compact digital thermometer and hygrometer designed for indoor use. It provides accurate readings of temperature and humidity, along with a comfort level indicator, time, and date display. Its versatile design allows for multiple placement options, making it suitable for various rooms in your home or office.
Video: Overview of the NOKLEAD Model 5253 features and setup.
2. Package Contents
- 1 x NOKLEAD Digital Thermometer Hygrometer (Model 5253)
- 1 x CR2032 Button Battery (pre-installed or included)
- 1 x Adhesive Pad
- 1 x User Manual
3. Product Features
- Temperature Display: Measures indoor temperature in Celsius (°C) or Fahrenheit (°F).
- Humidity Display: Measures indoor relative humidity (RH%).
- Air Comfort Indicator: Displays DRY, COMFORT, or WET conditions based on humidity levels.
- Time and Date Display: Includes a digital clock with 12/24-hour format and date.
- Fast Refresh Rate: Updates readings every 10 seconds.
- Large LCD Display: Clear and easy-to-read 3.26-inch LCD screen.
- Multiple Mounting Options: Built-in magnet, foldable stand, and adhesive pad for versatile placement.
- Compact Design: Small and portable (approx. 66mm x 71mm x 14mm).

Image: Key features of the NOKLEAD Digital Thermometer Hygrometer.
4. Setup
4.1 Battery Installation
- Locate the battery compartment on the back of the device.
- Open the battery compartment cover.
- If a plastic insulation tab is present, gently pull and remove it.
- Ensure the CR2032 button battery is inserted with the correct polarity (+ side facing up).
- Close the battery compartment cover securely.
- The device will power on automatically and display current temperature, humidity, time, and date.
4.2 Mounting Options
The device offers three convenient ways to place it:
- Tabletop Stand: Fold out the integrated stand on the back of the device to place it on any flat surface.
- Magnetic Attachment: The device has a strong built-in magnet, allowing it to be securely attached to metal surfaces like refrigerators.
- Wall Stick: Use the provided adhesive pad to mount the device on non-metallic surfaces. Ensure the surface is clean and dry before applying the adhesive pad. For best adhesion, allow the adhesive pad to set for 24 hours before attaching the thermometer.

Image: Multiple mounting options for versatile placement.
5. Operating Instructions
The device features three control buttons on the back: SET, +, and -.

Image: Rear view showing the control buttons.
5.1 Time and Date Setting
- Press and hold the SET button for approximately 3 seconds until the year display starts flashing.
- Use the + or - buttons to adjust the year.
- Press the SET button to confirm the year and move to the month setting.
- Repeat steps 2 and 3 to set the month, day, hour, and minute.
- After setting the minutes, press SET one last time to confirm all settings and exit the time/date setting mode. The display will return to normal operation.
5.2 12/24-Hour Time Format Setting
- In normal display mode, press the - button to switch between 12-hour (AM/PM) and 24-hour time formats.
5.3 Temperature Unit Setting (°C/°F)
- In normal display mode, press the + button to switch between Celsius (°C) and Fahrenheit (°F) temperature units.
5.4 Air Comfort Indicator
The device features a color-coded bar and text indicator to quickly assess indoor air comfort:
- DRY (Orange): Humidity is below 30%.
- COMFORT (Green): Humidity is between 30% and 69%.
- WET (Blue): Humidity is 70% or above.

Image: Explanation of the Air Comfort Indicator levels.
5.5 Calibration (Advanced)
If you suspect the readings are inaccurate, you can enter calibration mode:
- Press and hold both the + and - buttons simultaneously for a few seconds until the temperature or humidity reading starts flashing, indicating calibration mode.
- Use the + or - buttons to adjust the temperature or humidity offset.
- Press the SET button to switch between temperature and humidity calibration.
- Once adjustments are made, press the SET button again to save the calibration and exit the mode. If no buttons are pressed for 15 seconds, the device will automatically exit calibration mode without saving changes.
6. Maintenance
6.1 Cleaning
- Wipe the device with a soft, dry cloth.
- Do not use abrasive cleaners or solvents, as they may damage the display or casing.
6.2 Battery Replacement
- When the display becomes dim or shows an empty battery icon, it's time to replace the CR2032 button battery.
- Follow the battery installation steps (Section 4.1) to replace the battery.
- Ensure proper disposal of used batteries according to local regulations.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No display or dim display | Battery is low or incorrectly installed. | Replace the battery or ensure it's installed with correct polarity. |
| Inaccurate readings | Device placed in direct sunlight, near heat/cold sources, or needs calibration. | Relocate the device to a stable environment. Perform calibration if necessary (Section 5.5). |
| Display shows 'LL' or 'HH' | Temperature or humidity is outside the measurable range. | Move the device to an environment within the specified operating range. |
| Buttons unresponsive | Temporary software glitch or low battery. | Remove and reinsert the battery. Replace battery if low. |
8. Specifications
| Feature | Specification |
|---|---|
| Model | 5253 |
| Temperature Range | -9.9°C to 60°C (14.2°F to 140°F) |
| Temperature Accuracy | ±1°C |
| Humidity Range | 10% RH to 99% RH |
| Humidity Accuracy | ±3% RH to ±5% RH |
| Refresh Rate | Every 10 seconds |
| Display Type | LCD Digital |
| Display Size | 3.26 inches (diagonal) |
| Dimensions | Approx. 66mm x 71mm x 14mm (2.76 x 2.76 x 0.55 inches) |
| Power Source | 1 x CR2032 Button Battery |
| Battery Life | 8-12 months |
| Mounting Options | Stand, Magnet, Adhesive Pad |

Image: Detailed temperature and humidity accuracy specifications.
9. User Tips
- Placement: For accurate readings, place the device away from direct sunlight, drafts, heating vents, or air conditioning units. It's ideal for bedside tables or central room locations.
- Display Clarity: The LCD display is designed to be clear and visible even in daylight.
- Humidity Readings: Some users have noted a potential slight offset in humidity readings (e.g., 10% higher). If you observe this, consider using the calibration feature (Section 5.5) to fine-tune the sensor.
- Date Format: Be aware that the date format (DD/MM or MM/DD) might be fixed and not changeable on some units.
- Automatic Detection: The device automatically detects and displays temperature and humidity without manual input after setup.
10. Warranty and Support
10.1 Warranty Information
This NOKLEAD product comes with:
- A 60-day money-back guarantee for any reason.
- An 18-month warranty for quality-related issues.
Please retain your proof of purchase for warranty claims.
10.2 Customer Support
For any questions, technical assistance, or warranty claims, please contact NOKLEAD customer service:
Email: support@noklead.com