1. Important Safety Information
Read all instructions carefully before using the Awgem MF2 Spot Welding Machine. Failure to follow these instructions may result in damage to the product or personal injury. Keep this manual for future reference.
- Temperature and Moisture: Avoid exposing the device to extreme temperatures or moisture. This can damage the device and void the warranty. The device contains a battery, plastic, and sensitive electronic components.
- High Temperatures: Do not leave the device in an outdoor car for extended periods, as high temperatures may cause the internal battery to expand or explode.
- Battery Disposal: Batteries should be recycled or disposed of separately from household waste, in accordance with local environmental laws and guidelines.
- Children Safety: Keep away from children unless supervised by an adult.
- Intended Use: Do not use this product for purposes other than its intended use.
- Pre-use Inspection: Inspect the product before each use; do not use if damaged.
- Installation & Operation: Follow installation and operation guidelines to avoid injury.
- Water Exposure: Do not expose the device to water or moisture.
2. Product Overview
The Awgem MF2 is a portable Farad capacitor spot welding machine designed for precision welding tasks. It is suitable for mobile phone repair, battery assembly, metal welding, and features a burner function. The device utilizes new Farad capacitors for increased lifespan and strong output current.
3. Setup and Components
3.1 Unboxing and Initial Preparation
- Inspect Package Contents: Verify all items are present and undamaged.
- Remove Protective Films: Before first use, remove all protective films from the device and its components.
3.2 Charging
Connect the provided USB cable to a certified 5V power adapter to charge the device. The charging interface is Type-C/DC, with an input parameter of 5~20V/2A (MAX).
3.3 Welding Pen Assembly
The intelligent manual welding pen features a detachable design for easy maintenance and replacement of welding needles.
4. Operating Instructions
4.1 Power On/Off and Mode Selection
- Power On: Press and hold the power button for 3 seconds to turn on the device.
- Change Modes: Short press the power button to cycle through different operating modes. The device features a high-quality 320*170 high-definition color screen for clear display.
4.2 Welding Operations
The Awgem MF2 offers 99 gear adjustments and 10,000 types of fine-tuned outputs to suit various welding materials and thicknesses. It supports welding up to 0.4mm thickness.
- Integrated Diversion + Dual Pulse Welding: The device uses an integrated flow guiding and rapid cooling technology for firmer and more secure welds.
- Precision Spot Welding: The intelligent manual welding pen allows for precise triggering and spot welding.
- Visual Welding Area: The device incorporates ultra-thin insulation technology, increasing the weldable area and making maintenance more convenient.
4.3 Fine-Tuned Output Settings
The device offers extensive customization for welding parameters:
4.4 Applications
The Awgem MF2 is versatile and can be used for:
- Transplanting battery cells
- Battery assembly
- Metal welding
- Repairing phone frames
- Welding lens frames
- Burner function
5. Maintenance and Care
- Storage: After use, turn off the device and store it in a dry place, away from children.
- Cleaning: Ensure the welding pens and contact points are clean for optimal performance. Use sandpaper (included in package) if necessary.
- Durability: The device features a metal suspension guide rail, abandoning plastic sliding structures, to increase service life by 10 times.
6. Troubleshooting
If you encounter any issues with your Awgem MF2 Spot Welding Machine, please refer to the following general troubleshooting steps:
- Device Not Powering On: Ensure the device is fully charged. Press and hold the power button for 3 seconds.
- Poor Welding Effect: Check the welding parameters (Gear, Preheat, Trigger Time, Pause, Stitch Welding) and adjust them according to the material and thickness. Ensure the welding pens are clean and properly seated. Verify the material is within the weldable thickness range (up to 0.4mm for most materials, 0.25mm for pure nickel sheet).
- Overheating: Allow the device to cool down if it becomes excessively hot during prolonged use. Ensure proper ventilation.
- Display Issues: If the screen is unresponsive or shows abnormalities, try restarting the device.
For persistent issues, please contact customer support using the information provided in the Warranty & Support section.
7. Specifications
| Feature | Specification |
|---|---|
| Brand | Awgem |
| Model | MF2 Spot Welder (also H1/H2) |
| Gear Adjustment | 99 Gears |
| Charging Interface | Type-C/DC |
| Input Parameter | 5~20V/2A (MAX) |
| Output Interface | EC8 |
| Output Voltage | 6V (MAX) |
| Output Current | 1280A (MAX) |
| Screen Resolution | 320*170 |
| Product Size | 9.4 x 16.9 x 4.5 cm (3.7 x 6.65 x 1.77 inches) |
| Net Weight | Approx. 500g |
| Max Welding Thickness | 0.4mm (0.25mm for pure nickel sheet) |
| Lifespan Improvement | 10x (due to new Farad capacitors) |
| Package Dimensions | 21cm (L) x 15cm (W) x 11cm (H) |
| Package Weight | 1.008kg |
7.1 Security Protections
The Awgem MF2 is equipped with 9 levels of security protection:
8. Warranty and Support
8.1 Manufacturer Information
- Company Name: Shenzhen JueQi Technology Co., LTD
- Address: CN-Building A 907, Zhiyun Industrial Park, No.13, Huaxing Road, Henglang Community, Dalang Street, Long hua District, Shenzhen City
- Email: xiaomin.huang@jueqikj.com
- Telephone: 86-18818780728
8.2 EU Authorized Representative
- Company Name: MAGHREB TEX
- Address: FR-8 Rue Antonin Georges Belin, ARGENTEUIL, VAL D OISE
- Email: yuanfen429631@gmail.com
- Telephone: 33-615875362
8.3 Compliance Information
The Awgem MF2 Spot Welding Machine complies with the following standards:
- EN 55032:2015+A11:2020, EN 55035:2017+A11:2020
- EN IEC 61000-3-2:2019/A1:2021, EN IEC 61000-3-3:2013+A1:2019
- EN 61000-4-2:2019, ENC IEC 61000-4-3:2020
- EN 61000-4-2:2012, ENC 61000-4-5:2014+A1:2017
- EN 61000-4-2:2014, ENC 61000-4-8:2010
- ENC IEC 61000-4-11:2020
A detailed user manual in PDF format is available for download: User manual (PDF)
