Laser Tree K1 Max

Contents

LASER TREE K1 MAX Laser Engraver User Manual

Model: K1 Max | Brand: Laser Tree

1. Introduction

This manual provides detailed instructions for the safe and efficient operation, installation, and maintenance of your LASER TREE K1 MAX Laser Engraver. The K1 MAX is a powerful laser engraving and cutting machine featuring a 60W+ laser module, an air pump, and a honeycomb panel, designed for precision work across a large 800x600mm working area. Please read this manual thoroughly before operating the machine.

LASER TREE K1 MAX Laser Engraver with 60W Laser Module
The LASER TREE K1 MAX Laser Engraver with its 60W laser module.

2. Safety Statement

Before using the laser engraving machine, please peruse this safety manual attentively to comprehend the operating protocols and potential hazards associated with the laser engraving machine.

  1. Sharp edges may cut your hands when assembling the stand; gloves are recommended.
  2. Laser beams have high energy and heat. Direct contact with eyes or skin may cause serious injury. When the laser is working, always pay attention to the position and direction of laser beam movement.
  3. Children or teenagers are strictly prohibited from using the laser engraving machine alone.
  4. The laser engraver should be placed on a stable tabletop. Before use, please clean the work area to ensure that the surrounding environment is safe and free of debris, flammable, and explosive items to prevent potential safety hazards.
  5. Before using the laser, carefully check the power connection of the laser engraver. Make sure that the power cord is intact and the plug is firmly connected to avoid accidents caused by power problems.
  6. When the laser is working, you must wear professional protective glasses to protect your eyes from laser damage. Protective glasses can block the laser light and avoid direct exposure to the eyes.
  7. When the laser is working, the engraving area should be paved with metal or non-combustible mats to prevent the laser from burning the workbench or causing fire and other safety hazards.
  8. When the laser is working, please do not leave the equipment during operation. Stay focused and pay close attention to the operation of your equipment to prevent the engraving or cutting material from catching fire.
  9. When the laser is working, some materials produce smoke during laser cutting. Please keep the room well ventilated.
  10. Residue and debris can accumulate during the cutting and engraving process. Please clean up the work area promptly.
  11. Please ensure that a fire extinguisher is located near the laser engraving machine and that regular maintenance and inspections are conducted to promptly respond to any accidents that may occur.

3. Packing List

The LASER TREE K1 MAX comes with a comprehensive set of accessories to get you started. Please verify all components are present upon unboxing.

LT-K1 MAX 60W KIT Packing List overview
Overview of the LT-K1 MAX 60W kit components.

Included Components:

  • X-Axis Assembly x1
  • Y-Axis Assembly x2
  • Front Frame x1
  • Rear Frame x1
  • X-Axis Pulley Fixing Plate x1
  • Support Feet x3
  • Main Control Box x1
  • Y-Axis Timing Belt x2
  • Main Cable x1
  • Power Adapter x1
  • AC Cable x1
  • Card Reader x1
  • TF Card x1
  • USB Cable x1
  • Laser Module x1 (60W)
  • Spare Laser Protective Lens x2
  • Honeycomb Panel x1
  • Desktop Protection Plate x1
  • M4*30 Adjusting Screw x2
  • T-Nut x4
  • M4*5 Fasten Screw x4
  • M4*18 Round Screw x1
  • M5*10 Round Screw x2
  • M5*20 Round Screw x16
  • M5*20 Flat Screw x1
  • Limiting Column Sleeve x1
  • Material Pack x1
  • Air Pump User Manual x1
  • K1 Max User Manual x1 (this document)
  • Square Pad x4
  • L-Allen Wrench x4
  • 8-10 Open Spanner x1
  • Cable Ties x1
  • Cleaning Brush x1
Detailed Packing List of components
Detailed view of all included components.

4. Installation Guide

4.1 Assembly of X-axis Pulley

Attach the pulley plate to the right side of the X-axis using the corresponding M4*18 Round Screw (x1) and M5*10 Round Screw (x2) as shown in the diagram. Note: M4*18 screw is used to set the tension of the timing belt. Do not tighten the screw completely or the timing belt may be damaged.

4.2 Assembly of Timing Belt and Y-axis

  1. Flip the X-axis.
  2. Pass the timing belt through the X-axis pulleys and gears. Both ends operate in the same way. When installing the timing belt, keep the belt teeth upwards.
  3. Pass the Y-axis beam through the pulley fitted with the timing belt. Both ends operate in the same way. When flipping the X-axis to install the Y-axis, the holes in the Y-axis should be downwards.

4.3 Assembly of Front Frame

  1. Use M5*20 round screws (x4) to fix the front frame.
  2. To adjust the belt, push the T-nut into the Y-axis front frame groove and secure the timing belt with the M4*5 fasten screw (x2). Repeat for both left and right sides. Press the middle span of the timing pulley with your finger to ensure the belt is flexible. If it's too loose or too tight, it needs adjustment.
  3. Use M5*20 round screws (x4) to install the support corners on both sides of the front frame.

4.4 Assembly of Rear Frame

  1. Use M5*20 round screws (x4) to fix the rear frame.
  2. Push the X-axis towards the front beam for a snug fit.

4.5 Assembly of Limiting Column

Install the limiting column sleeve using the M5*20 flat screw.

4.6 Assembly of Main Cable

Connect the main cable to the distribution box and motor, and then to the mainboard control box.

4.7 Assembly of Laser Module

  1. Attach the M4*30 adjusting screw (x2) into the first and third holes of the X-axis dovetail backplate.
  2. Assemble the laser module and connect the inputs and air assist to the laser module.

5. Interface Description

5.1 Main Control Box Interface Description

  1. Power input: Aviation 4P plug, voltage DC 24V, current 10A.
  2. Device main cable interface: PHB2.0-2*10PIN buckle terminal, connected to the distribution box.
  3. Air assistance output: DC5.5*2.1mm socket, output DC 24V.
  4. USB-PC interface: Port type USB-B, Connect with PC and burn program.
  5. Power switch: Self-locking switch, controls the current on and off of the whole machine, with red indicator light.
  6. TF card slot: Stores offline engraving files. Recommended TF card type is Class 10, 4~16G, Fat32 format. Supported offline engraving file format is .nc.gc.
  7. Emergency stop switch: Stops the device action and PWM signal output and disconnects the device from the PC.

5.2 Distribution Box Port Description

  1. Rotary axis switching: Y-axis motor and rotary axis motor control switching.
  2. Y-axis motor output and limit signal input.
  3. X-axis motor output and limit signal input.
  4. Laser module output interface: MR30 port (DC 24V, GND, PWM).
  5. Device main cable interface: Connect to the main control box.
  6. Rotary axis output: PH2.0-4PIN terminal, connected to the rotary table motor.

5.3 Laser Module Features

Laser Module Features: Accurate Focus, Air Assist, Cable Drag Chain, Red Cross Line Locating, TF Card Offline Engraving, Max Engraving Speed, Security Protection.
Key features of the K1 MAX laser module.
  • Power indicator: Red when power supply is connected.
  • Signal indicator: Green when signal is received.
  • Working temperature display: Built-in thermistor shows real-time working temperature. An alarm sounds if temperature exceeds 55°C. Keep below 55°C for optimal performance.
  • Switch: Press once to turn off over-temperature alarm. Long press 5S to switch optical power (60W → 40W → 20W).

6. Software Connection Guide

The K1 MAX supports LaserGRBL and LightBurn engraving software.

6.1 LaserGRBL

  1. Connect one end of the USB data cable to the engraving machine and the other end to the USB port of the computer with LaserGRBL software installed.
  2. Connect the power port of the engraving machine through the DC24V adapter and turn on the power switch.
  3. Open the LaserGRBL software on the computer, select the correct COM port and click connect. If the status bar displays "SimpleLaser 1.1h", the connection is successful.

6.2 LightBurn

  1. Connect one end of the USB data cable to the engraving machine and the other end to the USB port of the computer with LightBurn software installed.
  2. Connect the power port of the engraving machine through the DC24V adapter and turn on the power switch.
  3. Open the LightBurn software, select "Start Your Free Trial" or "Activate License".
  4. Create a new device, select "GRBL".
  5. Select USB connection.
  6. Set the engraving size to 800*600mm and modify the device name to "K1 MAX".
  7. Set the origin position of the machine and turn off automatic reset on power-on. (If you need to automatically reset every time you turn on the computer, please tick step 2 of the attached diagram in the PDF manual).
  8. Complete software setup.
  9. Select the "K1 MAX" device and the correct COM port. When the status bar displays Ready, the device is successfully connected.

7. Machine Test Guide

7.1 LaserGRBL Test

  1. Engraving machine reset test: Find the reset button on the default interface of LaserGRBL and click it. Under correct operation, the laser module should move to the side of the control box and stop moving when it hits the limit column.
  2. Engraving machine movement test: Find the direction button on the default interface of LaserGRBL and set the moving distance and speed (recommended moving distance is 10mm). Click in any direction. Under correct operation, the laser module should move in the direction shown by the arrow.
  3. Laser module light test: Find the light button on the LaserGRBL default interface and press and hold it. Under correct operation, the laser module should emit blue light normally.

7.2 LightBurn Test

  1. Engraving machine reset test: Find "Home" in the lower right corner of LightBurn default interface and click on it. Under correct operation, the laser module should move to the side of the control box and stop moving when it hits the limit column.
  2. Engraving machine movement test: Find "Move" in the lower right corner of LightBurn default interface and open it. Set the moving distance and speed (recommended moving distance is 50mm). Click in any direction. Under correct operation, the laser module should move in the direction indicated by the arrow.
  3. Laser module light test: Open the device settings, turn on the laser ignition option and set air assist to M7. Find "Move" in the lower right corner of the LightBurn default interface, set the optical power to 0.5% and click "Fire". Under correct operation, the laser module should emit blue light.

8. Laser Module Focus Guide

The K1 MAX laser module has a working focal length of 40mm.

8.1 Focusing for Cutting

When cutting, you only need to make the focus locate a bit lower than the surface of materials. For example, if you want to cut 12mm material, the focus should be 6mm lower than the material surface. Please adjust the fixed focus lever to 6mm.

Fixed Focus Lever Usage Reference (Cutting)

Material thickness< 5mm5mm8mm10mm12mm15mm> 30mm
Fixed focus lever0mm2mm4mm5mm6mm7mm7mm

8.2 Focusing for Engraving

When engraving, please ensure that the focus is located on the material surface. For example, if you want to perform engraving, just adjust the fixed focus lever to 0mm.

Reference Settings for Engraving

Parameter MaterialFixed focus lever (mm)Speed (mm/min)Max PowerLine Interval
20W40W60W20W40W60W
Basswood Plywood012000150001800050%45%30%0.05
Pine Board010000120001500055%50%40%0.05
Stainless Steel09000100001300060%70%80%0.01

8.3 One-Pass Cutting Depth Examples

Cutting in One Pass examples: 20mm Plywood, 30mm Acrylic, 40mm Pine Wood
Examples of one-pass cutting depth for various materials.
  • 20mm Basswood Plywood: 1 pass cutting.
  • 40mm Pine Board: 1 pass cutting.
  • 30mm Black Acrylic: 1 pass cutting.
K60 Series - Three Power Options (20W, 40W, 60W) with one-pass cutting depth examples
Detailed one-pass cutting depths for 20W, 40W, and 60W settings.

9. Specifications

AttributeValue
Brand NameLaser Tree
ModelK1 Max
Model NumberLT-K1-MAX-60W
Laser Optical Power60W+
InputDC 24V 10A
Engraving Area800x600mm
Power Adjustable20W-40W-60W
Spot Size (20W)0.15x0.15mm
Spot Size (40W)0.15x0.18mm
Spot Size (60W)0.15x0.25mm
Engraving Speed20000mm/min
Wavelength450nm (±10nm)
Focus Length40mm
Support SoftwareLightBurn & LaserGRBL
Air AssistanceYes
Rotation Axis OutputYes
Offline EngravingYes
Emergency StopYes
Tilt ProtectionYes
Status IndicatorYes
Operating Temperature0-60°C
OriginMainland China
CertificationCE, RoHS, WEEE
Exceptionally Large Working Area (800x600mm)
The K1 MAX offers an exceptionally large 800x600mm working area.

10. Maintenance

10.1 Laser Module Lens Cleaning

When the laser module is used for a long time, you need to use an alcohol swab to wipe the laser protective lens to ensure the best cutting and engraving performance.

Caution for lens cleaning:

  • Before wiping the lens, make sure the power is turned off and the laser module is disconnected from the engraving machine.
  • After wiping, allow the lenses to dry naturally for 3 to 5 minutes before use.

Use the alcohol swab to clean or replace with a spare protective lens.

10.2 Storage

When the laser module is not used for a long time, please ensure that the lens is not polluted by dust.

For more information about maintenance, please contact us at lasertree@micost-optotech.com.

11. Troubleshooting

Common Issues and Solutions:

  • Machine not connecting to software: Ensure the USB cable is securely connected to both the engraver and your computer. Verify that the correct COM port is selected in LaserGRBL or LightBurn. Check the power switch and ensure the device is powered on.
  • Laser not firing or weak output: Check the laser module's power indicator. Perform the laser module light test as described in the Machine Test Guide to confirm it emits blue light. Ensure the optical power setting in your software is appropriate for the material.
  • Engraving/Cutting results are inconsistent: Verify the laser module focus is correctly set for your material and operation (cutting or engraving). Refer to the 'Laser Module Focus Guide' section. Ensure the material is flat and securely placed.
  • Machine stops unexpectedly or alarms: Check for tilt detection. If the machine tilts, it will beep an alarm and stop operation for safety. Ensure the machine is on a stable, level surface.
  • Software configuration for GRBL ($100 and $101 step/mm): For precise control, users often need to configure the $100 and $101 settings in GRBL for step/mm. Consult the LaserGRBL or LightBurn documentation for specific calibration procedures based on your machine's movement and desired accuracy.

12. User Tips

  • Harness the Power: The K1 MAX is a very powerful machine. Always start with lower power settings and gradually increase as needed to avoid over-burning or damaging materials.
  • Optimal Air Assist: Utilize the air assist feature, especially during cutting, to achieve cleaner cuts and reduce charring. Adjust airflow based on material and power settings.
  • Offline Engraving Convenience: For repetitive tasks or when a PC connection is inconvenient, prepare your .nc.gc files on a TF card for offline engraving.
  • Workspace Management: Keep your large 800x600mm workspace clear and organized. Use the honeycomb panel and desktop protection plate to protect your work surface and improve results.
  • Regular Cleaning: Periodically clean the laser lens and the machine's rails to maintain optimal performance and extend the lifespan of your engraver.

13. Warranty & Support

All products come with a 1-year warranty from our store. For any inquiries or support needs, please contact us. We aim to answer all emails within 24 hours.

14. Additional Resources

For a downloadable PDF version of this user manual and other related documents, please refer to the official product page or contact support. The PDF manual can be found at: LASER TREE K1 MAX User Manual (PDF)

© 2024 Laser Tree. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.