AZDOME Hardwire Kit OBD Instruction Manual

Introduction

The AZDOME Hardwire Kit OBD is designed to provide continuous power to your AZDOME dash camera, enabling 24-hour parking monitoring and protecting your vehicle's battery from over-discharge. This kit connects directly to your vehicle's OBD port, offering a clean and efficient power solution without occupying the cigarette lighter port.

This manual provides detailed instructions for installation, operation, and maintenance of your AZDOME Hardwire Kit OBD.

Key Features

• 24-Hour Parking Monitoring: Automatically enables time-lapse recording or emergency video saving upon collision detection when the vehicle is off.
• Low Voltage Monitoring: Automatically cuts power to prevent vehicle battery over-discharge.
• Efficient Power Output: Delivers a maximum output current of 2.5A.
• Multiple Protection Features: Includes safety, input short-circuit, output high voltage, over-current, short-circuit, and over-temperature protection.
• Easy Installation: Designed for straightforward connection to the vehicle's OBD port.
• Compatibility: Available with Micro USB, Mini USB, and Type C ports to fit various AZDOME dash cam models.

Compatibility

The AZDOME Hardwire Kit OBD is available with different port types to ensure compatibility with various AZDOME dash cam models:

• OBD01 (Type-C Port): Compatible with M580, M560, M660, M330, GS63Pro, GS63H Pro, PG19X, PG18S, PG16S, M27.
• OBD02 (Micro USB Port): Compatible with M300S, M300, M301.
• OBD03 (Mini USB Port): Compatible with M550, M550 Pro, PG17, M63 Lite, GS63H, M01 Pro, M200, M17, PG02S-R, PG16S-R.

Setup and Installation

Follow these steps to install your AZDOME Hardwire Kit OBD:

1. Locate the OBD Interface: Find your vehicle's OBD interface. It is usually located in the lower left corner of the steering wheel area.
2. Connect the OBD Plug: Align the OBD plug of the hardwire kit with the vehicle's OBD interface and plug it in directly.
3. Route the Cable:
   • Gently pull down the vehicle door ceiling strip.
   • Insert the wire along the gap between the ceiling strip and the vehicle's interior.
   • Continue routing the cable neatly along the A-pillar and the top edge of the windshield towards your dash camera's mounting location.
   • Use a pry tool (if necessary) to tuck the cable securely into the gaps.
4. Connect to Dash Camera: Insert the power interface (Micro USB, Mini USB, or Type C, depending on your kit version) into your dash camera.

This installation method ensures a clean setup, making installations simple and convenient.

Operating Instructions

Once installed, the AZDOME Hardwire Kit OBD operates automatically to manage power for your dash camera, especially for parking monitoring functions.

24-Hour Parking Monitoring

When your vehicle's ignition is turned off, the hardwire kit will signal your dash camera to enter parking monitoring mode. This mode typically includes:

• Time-Lapse Recording: The dashcam records continuously at a low frame rate (e.g., 1fps) to save storage space while covering extended periods.
• Collision Detection: If a collision or significant impact is detected while parked, the dashcam will automatically save an emergency video clip to protect crucial evidence.

Low Voltage Monitoring

The hardwire kit is equipped with a low voltage protection feature. If your vehicle's battery voltage drops below a safe threshold, the kit will automatically cut off power to the dash camera. This prevents excessive drain on your car battery, ensuring you can start your vehicle without issues.

Maintenance

The AZDOME Hardwire Kit OBD requires minimal maintenance. To ensure optimal performance:

• Periodically check the connections to the OBD port and the dash camera to ensure they are secure.
• Ensure the cable routing remains neat and does not interfere with vehicle operation or safety features.
• Keep the OBD port free from dust and debris.

Troubleshooting

If you encounter issues with your AZDOME Hardwire Kit OBD, consider the following:

Dash Cam Not Powering On in Parking Mode:

• Check Connections: Ensure the hardwire kit is securely plugged into both the OBD port and the dash camera.
• Vehicle Battery Voltage: The kit might have cut power due to low vehicle battery voltage. Start your car to recharge the battery.
• Dash Cam Settings: Verify that your dash camera's parking mode feature is enabled and configured correctly in its settings.

Dash Cam Not Recording While Parked:

• SD Card Issues: Check if the SD card is full, corrupted, or not inserted correctly. Format the SD card if necessary (back up important files first).
• Motion/Impact Sensitivity: Adjust the sensitivity settings for parking mode on your dash camera. If too low, it might not trigger recordings.

General Power Issues:

• Incorrect Port Type: Ensure you are using the correct hardwire kit version (Micro USB, Mini USB, or Type C) for your specific dash cam model.
• OBD Port Functionality: If other OBD devices also fail, there might be an issue with your vehicle's OBD port. Consult a mechanic.

Specifications

User Tips

• Check Compatibility: Before purchasing, always confirm the correct port type (Micro USB, Mini USB, or Type C) for your specific AZDOME dash cam model to ensure proper fit and function.
• Alternative Dash Cams: While designed for AZDOME, some users inquire about compatibility with other brands like 70mai. Always verify power requirements and port types for non-AZDOME dash cams.
• Secure Cable Routing: Take your time to route the cable neatly and securely to avoid interference with vehicle controls and to maintain a clean interior aesthetic.

Warranty and Support

For warranty information, technical support, or further assistance, please refer to the official AZDOME website or contact their customer service directly. Keep your purchase receipt as proof of purchase for any warranty claims.