HOBBYWING EZRUN MAX8 G2

Contents

HOBBYWING EZRUN MAX8 G2 ESC & Brushless Motor Set User Manual

Model: EZRUN MAX8 G2

Brand: HOBBYWING

Introduction

This manual provides essential instructions for the proper setup, operation, and maintenance of your HOBBYWING EZRUN MAX8 G2 Inductive Brushless ESC and Motor Set. Please read this manual thoroughly before use to ensure optimal performance and safety.

Safety Information

  • Always disconnect the battery from the ESC when not in use.
  • Ensure all connections are secure and properly insulated to prevent short circuits.
  • Operate RC models in open areas away from people, animals, and obstacles.
  • Keep the ESC and motor away from moisture and extreme temperatures unless specified otherwise.
  • Recommended for users aged 14 years and older.

Setup and Installation

The EZRUN MAX8 G2 ESC and motor are designed for 1/10 and 1/8 scale RC cars and buggies.

Component Overview

HOBBYWING EZRUN MAX8 G2 160A ESC with XT90 connectors and power switch

Image: The HOBBYWING EZRUN MAX8 G2 160A ESC, showing the main unit, power wires with XT90 connectors, and the external power switch.

Wiring and Connections

  • Input Wires: Red-10AWG-150mm*1 / Black-10AWG-150mm*1. Connect these to your battery.
  • Output Wires: Red-10AWG-200mm*1. Connect these to the motor.
  • Input Connectors: XT90. Ensure your battery uses compatible XT90 connectors.
  • Output Connectors: 6.5 Bullet Connectors (Female). Connect to the motor's male bullet connectors.
  • Sensored Cable Interface: The MAX8 G2 ESC features a new type of sensored cable interface. It is highly recommended to use Hobbywing motors for optimal waterproof protection (IP67). This ESC also supports wires with standard interfaces.
Diagram of new sensored cable interface for MAX8 G2 ESC

Image: Diagram illustrating the new sensored cable interface on the MAX8 G2 ESC, compatible with Hobbywing motors for enhanced waterproofing.

Motor Compatibility

The current brushless system is best paired with the EzRun 4268/4278 SD G2 motors to achieve maximum performance and ensure motor protection against overheating.

Diagram showing MAX8 G2 ESC combined with 4268 SD G2 motor

Image: Illustration of the MAX8 G2 ESC and 4268 SD G2 motor as a perfect combination for optimal performance.

Operation

Powering On/Off

Use the external power switch to turn the ESC on or off. Ensure all connections are secure before powering on.

Programming the ESC

The EZRUN MAX8 G2 ESC supports multiple programming methods:

  • LED Programming Box: Supported.
  • LCD Programming Box: Supported.
  • OTA Programmer: Supported.

The programming interface is shared with the cooling fan port.

Advanced Features

  • Sensored Mode: The MAX8 G2 ESC supports sensored mode, offering flexible and precise control, especially at low speeds.
  • Turbo Technology: The 1/8th Brushless System Turbo Technology allows for adjustable turbo parameters (up to 32 degrees), significantly increasing speed by up to 25%.
  • Real-time Data & Data Logging: After connecting an OTA module, you can enable real-time data recording to monitor the operating status via a smartphone app. The Bluetooth transmission distance is most effective within a 5m radius.
Diagram illustrating 1/8th Brushless System Turbo Technology with 25% speed increase

Image: Diagram showing the 1/8th Brushless System Turbo Technology, which can increase speed by up to 25%.

Smartphone app displaying real-time data and data logging for the ESC

Image: A smartphone screen displaying real-time data such as RPM, throttle, ESC voltage, and motor temperature, accessible via an OTA module.

Maintenance and Care

Cooling System

The ESC features an efficient cooling system with a frameless fan design and integrated housing radiator. SMART technology helps reduce the overall operating temperature by approximately 25°C compared to previous generations, enhancing reliability.

Diagram illustrating the efficient cooling system of the MAX8 G2 ESC

Image: Diagram showing the internal components and airflow of the efficient cooling system within the MAX8 G2 ESC.

Comparison showing 25 degree Celsius temperature reduction with SMART technology

Image: Visual representation of how SMART technology reduces the operating temperature of the EzRun Max8 G2 by approximately 25°C.

Waterproof and Dustproof Performance

The IP-67 system guarantees excellent waterproofing and dustproofing. The power system can operate in muddy, sandy, icy, and snowy conditions without damage.

RC car operating in various weather conditions, highlighting IP-67 waterproof and dustproof features

Image: An RC car driving through dirt, illustrating the product's applicability to all weather track conditions due to its IP-67 rating.

Capacitor Thermal Protection

The ESC implements capacitor thermal protection to prevent capacitors from exploding and causing irreversible damage due to overload.

Diagram illustrating capacitor thermal protection feature

Image: Diagram showing the capacitor thermal protection mechanism, designed to prevent damage from overload.

Built-in Capacitors

The ESC has three built-in 680uF capacitors, increasing performance by 74% (870uF total) compared to the previous MAX8 ESC. These ultra-large capacitors eliminate the need for external capacitors on most vehicles.

Diagram showing built-in capacitors and 74% performance enhancement

Image: Close-up view of the built-in 680uF capacitors, highlighting the 74% performance enhancement over the previous EzRun Max8.

Super Built-in BEC

The ESC features a built-in BEC with a maximum output current of up to 15A. Output voltages are switchable between 6V, 7.4V, and 8.4V, supporting demanding high-torque servos.

Diagram highlighting the Super Built-in BEC feature of the MAX8 G2 ESC

Image: Diagram emphasizing the Super Built-in BEC, capable of supporting high-torque servos with adjustable voltage outputs.

Troubleshooting

If you encounter issues with your EZRUN MAX8 G2 ESC and Motor Set, consider the following common troubleshooting steps:

  • No Power: Check battery connections, ensure the battery is charged, and verify the power switch is in the 'on' position.
  • Motor Not Responding: Check all motor-to-ESC connections. Ensure the sensored cable is properly connected if operating in sensored mode. Verify transmitter and receiver are correctly bound and powered.
  • Overheating: Ensure proper ventilation around the ESC and motor. Check for any obstructions to the cooling fan. Reduce load or adjust gearing if consistent overheating occurs.
  • Erratic Behavior: Check for loose wiring or damaged components. Ensure proper calibration of the ESC with your transmitter.
  • Programming Issues: Ensure the programming device (LED/LCD box or OTA module) is correctly connected and powered. Refer to the specific programming device manual for detailed instructions.

For persistent issues, contact HOBBYWING customer support or your retailer.

Specifications

Detailed specifications table for Hobbywing EzRun Max8 G2 ESC

Image: Comprehensive table detailing the specifications of the EzRun Max8 G2 ESC, including type, current, battery support, BEC output, and dimensions.

EZRUN MAX8 G2 ESC Specifications
Feature Detail
Product NameEzRun Max8 G2
Product Number30103203
Type1/8th Scale, Brushless, Sensored/Sensorless (BL/SD), Waterproof (Yes)
Continuous/Peak Current160A/1050A
Input Voltage3-6S LiPo
BEC Output6V/7.4V/8.4V adjustable, continuous current 6A (switch-mode)
Input WiresRed-10AWG-150mm*1 / Black-10AWG-150mm*1
Output WiresRed-10AWG-200mm*1
Input ConnectorsXT90
Output Connectors6.5 Bullet Connectors (Female)
ESC Programming viaLED Program Box (Supported), LCD Program Box (Supported), OTA Programmer (Supported), Program Port (PRG/Fan Port)
Fan Size30x30x10mm
Fan Voltage Range6-8.4V
Fan Powered byBEC
Data RecordingExtreme value (Supported), Real-Time Data (Supported), Historical data (Graph) (Supported)
Firmware UpgradeSupported
Size60mm*48mm*40.5mm
Weight192g
Applications (Motors)Sensored brushless motors / Sensorless brushless motors
Applications (Vehicles)1/8th Truck, Monster Truck
KV Rating/T CountWith 6S LiPo: KV≤3000; With 4S LiPo: KV≤4278 size motor
MaterialMetal
Recommended Age14+ years

User Tips

  • This product is confirmed to be a genuine HOBBYWING item, ensuring quality and compatibility.
  • Always verify the product specifications against your RC model's requirements before installation to ensure proper fit and function.

Warranty and Support

For warranty claims, technical support, or service inquiries, please contact HOBBYWING directly or the authorized retailer from whom you purchased the product. Keep your proof of purchase for any warranty-related requests.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.