NJTY DT-6013

Contents

Digital Capacimeter DT-6013 Instruction Manual

Brand: NJTY | Model: DT-6013

1. Introduction

The NJTY DT-6013 is a professional digital capacimeter designed for high-precision measurement of capacitor capacity. Featuring a 6000-count display and a wide capacitance range up to 100,000uF (100mF), it is an essential tool for electronics enthusiasts, technicians, and professionals. This manual provides detailed instructions for safe and effective use of your device.

2. Safety Information

Please read and understand all safety information before operating this device. Failure to follow these instructions may result in electric shock, fire, or damage to the meter or the device under test.

  • Always ensure the capacitor under test is fully discharged before connecting the capacimeter. Capacitors can store dangerous electrical charges.
  • Do not apply voltage exceeding 30V to the CX input terminals.
  • Do not operate the meter if it appears damaged or if the battery cover is not properly closed.
  • Keep the device away from water and extreme temperatures.
  • Replace batteries promptly when the low battery indicator appears to ensure accurate readings.

3. Product Overview

Familiarize yourself with the components of your DT-6013 Digital Capacimeter:

Labeled diagram of DT-6013 Capacimeter front panel
Figure 3.1: Front Panel Layout of DT-6013
  • Backlit Display: Shows capacitance readings and other indicators.
  • HOLD/* Button: Used for Data Retention (HOLD) and Backlighting control.
  • ZERO Button: Used to zero out residual capacitance before measurement.
  • Gear Knob: Rotary switch to select capacitance measurement ranges (600PF to 100mF) and power OFF.
  • Capacitance Test Hole (CX): Input for direct capacitor testing.
  • Red Test Clip Jack (CX MAX 30V): Positive input for test leads.
  • Black Test Clip Jack (CX MAX 30V): Negative input for test leads.

4. Setup

4.1 Battery Installation

  1. Ensure the capacimeter is powered off (Gear Knob set to OFF).
  2. Locate the battery compartment on the back of the device.
  3. Open the battery cover.
  4. Insert two 1.5V AA batteries, observing the correct polarity (+/-).
  5. Close the battery cover securely.
Battery compartment of DT-6013 showing battery installation
Figure 4.1: Battery Compartment

4.2 Connecting Test Leads

Connect the red and black test clips to the corresponding red and black CX jacks on the front panel of the capacimeter.

5. Operating Instructions

5.1 Power On/Off

To power on the device, rotate the Gear Knob from the "OFF" position to any desired capacitance range. To power off, rotate the Gear Knob back to the "OFF" position.

5.2 Range Selection

Select the appropriate capacitance range using the Gear Knob. Start with a higher range if the capacitance value is unknown, and then decrease the range for more precise readings.

5.3 Zeroing

Before measuring, especially for small capacitance values, it is recommended to zero the meter. With the test leads open (not connected to a capacitor), press the "ZERO" button. This compensates for any residual capacitance in the test leads.

5.4 Measuring Capacitance

  1. Ensure the capacitor to be measured is fully discharged.
  2. Connect the red and black test clips to the terminals of the capacitor.
  3. Read the capacitance value displayed on the screen.
Examples of capacitance measurements with DT-6013
Figure 5.1: Capacitance Measurement Examples

5.5 Data Hold

Press the "HOLD/*" button to freeze the current reading on the display. Press it again to release the data hold function.

5.6 Backlight

The "HOLD/*" button also controls the screen backlighting. A short press typically toggles the backlight on/off, or it may activate automatically when powered on.

Video 5.1: Demonstration of DT-6013 Capacimeter in use, showing display and controls.

6. Maintenance

6.1 Cleaning

Wipe the device with a dry, soft cloth. Do not use abrasive cleaners or solvents.

6.2 Battery Replacement

When the low battery indicator appears on the display, replace the batteries as described in Section 4.1. Always use two new 1.5V AA batteries.

6.3 Storage

If the device is not used for an extended period, remove the batteries to prevent leakage. Store the capacimeter in a cool, dry place, away from direct sunlight and extreme temperatures.

7. Troubleshooting

  • No Display/Faint Display: Check battery installation and charge. Replace batteries if necessary.
  • "OL" or Over-range Indicator: The measured capacitance exceeds the selected range. Switch to a higher range.
  • Inaccurate Readings: Ensure the meter has been zeroed before measurement. Check for proper connection of test leads to the capacitor. Ensure the capacitor is fully discharged.
  • Low Voltage Alert: The battery voltage is low. Replace the batteries.

8. Specifications

Technical Specifications - DT-6013 Capacimeter
ParameterValue/Description
Model NumberDT-6013
Brand NameNJTY (cretrust)
Display Counts6000 Counts
Capacitance Range600pF / 6nF / 60nF / 6uF / 60uF / 600uF / 6000uF / 60mF / 100mF
Capacitance Precision600pF: ±2%+10
6nF - 600uF: ±0.6%+10
6000uF: ±2%+10
60mF: ±4%+10
100mF: ±5%+10
Resolving Power0.1pF (600pF) to 0.1mF (100mF)
On-off BuzzerYes
Data HoldYes
Screen BacklightingYes
Measurement MethodDouble integral A/D conversion
Sampling RateApprox. 3 seconds per second
Low Voltage DisplayYes
Over-range DisplayThe highest position shows "1"
Battery2 x 1.5V AA (No Battery Included)
Dimensions148 x 70 x 35 mm
CertificationCE
OriginMainland China

9. User Tips

  • Always ensure the capacitor is fully discharged before connecting it to the capacimeter. This prevents potential damage to the meter and ensures accurate readings.
  • For optimal accuracy, especially with small capacitors, perform the "ZERO" function before each measurement.
  • The DT-6013 is capable of measuring a wide range of capacitors, up to 100,000 microfarads (100mF). If you encounter an "OL" reading, try switching to a higher range.

10. Warranty and Support

For any questions, technical assistance, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.