DATAKOM DKG105

Contents

DATAKOM DKG105 Generator Engine Controller

Model: DKG105

1. Introduction

The DATAKOM DKG105 is a microprocessor-based digital unit designed for the automatic control of a genset. It provides all necessary functions for automatic starting, stopping, and load transfer of a generator, making it a cost-effective and space-saving solution for basic genset control. The unit monitors the mains voltage, manages generator operations, and incorporates internal protections and external fault inputs.

2. Key Features

  • Automatic engine starting and stopping
  • Support for gas engines
  • Automatic mains failure monitoring
  • Automatic load transfer
  • Automatic shutdown on fault conditions
  • Test mode availability
  • Survives cranking dropouts
  • Digital engine run-hours display
  • Provision for energize to stop, preheat & choke outputs
  • Mains phases voltage limits checking
  • Generator phase voltage limits checking

3. Setup and Installation

The DKG105 unit is designed to fit into a standard 72x72mm panel meter opening. Ensure the panel cutout is precise for a secure fit. The unit features pluggable terminal blocks for easy wiring.

3.1. Physical Installation

  1. Prepare a 72x72mm cutout in your control panel.
  2. Insert the DKG105 unit into the cutout from the front.
  3. Secure the unit using the provided mounting clips from the rear of the panel.

3.2. Wiring Connections

Refer to the rear view of the controller for terminal identification. The unit comes with green pluggable terminal blocks for all connections.

Rear view of DKG105 controller showing terminal connections
Figure 1: Rear view of the DKG105 controller with terminal labels.

The terminal connections are as follows:

Terminal No.DescriptionTerminal No.Description
1M NEUT (Mains Neutral)8HI.TEMP (High Temperature Input)
2PHASE-G (Generator Phase)9OIL PR. (Oil Pressure Input)
3G.CONT (Generator Contactor Control)10FUEL (Fuel Solenoid Output)
4PHASE-T (Mains Phase T)11CRANK (Crank Output)
5PHASE-S (Mains Phase S)12AUX (Auxiliary Output)
6PHASE-R (Mains Phase R)13BAT- (Battery Negative)
7M.CONT (Mains Contactor Control)14BAT+ (Battery Positive)

Ensure all connections are made according to your generator's wiring diagram and local electrical codes. Incorrect wiring can cause damage to the unit or the generator.

4. Operating Instructions

The DKG105 controller features a user-friendly front panel with a 3-digit LED display, status indicators, and control buttons.

Front view of DKG105 controller with buttons and indicators
Figure 2: Front panel of the DKG105 controller.

4.1. Control Buttons

  • RUN (Green button): Initiates manual generator start.
  • OFF (Red button): Stops the generator and resets any alarms.
  • AUTO (A button): Activates automatic mode for mains failure detection and automatic generator operation.
  • MENU (Arrow button): Navigates through parameters and settings for digital adjustment.

4.2. Status Indicators

  • GENSET: Indicates generator status (running, standby).
  • MAINS: Indicates mains power status (present, absent).

4.3. Automatic Mode

In AUTO mode, the DKG105 continuously monitors the 3 phases of the mains voltage. Upon detecting a mains failure, it will automatically initiate the generator start sequence, transfer the load, and monitor the generator's operation. When mains power is restored, it will transfer the load back to the mains and shut down the generator.

4.4. Parameter Adjustment

The unit allows for digital adjustment of timers and threshold levels via the push-buttons on the unit. Use the MENU button to navigate through parameters and adjust values as needed. Refer to the detailed programming guide (if available from manufacturer) for specific parameter settings.

5. Maintenance

The DKG105 controller is designed for reliable operation with minimal maintenance. However, regular checks can ensure optimal performance and longevity:

  • Visual Inspection: Periodically check the unit for any signs of physical damage, loose connections, or dust accumulation.
  • Cleaning: Keep the front panel clean using a soft, dry cloth. Avoid using abrasive cleaners or solvents.
  • Connection Integrity: Ensure all wiring connections to the terminal blocks are secure and free from corrosion.
  • Environmental Conditions: Ensure the operating environment remains within the specified temperature and humidity ranges to prevent premature failure.

6. Troubleshooting

The DKG105 provides fault indicators on the front panel to assist in diagnosing issues:

IndicatorPossible CauseAction
START FAILGenerator failed to start after multiple attempts.Check fuel level, battery, starter motor, and engine.
SPEEDEngine speed anomaly (overspeed/underspeed).Check engine governor, speed sensor, and load.
OIL PRESS.Low oil pressure detected.Check engine oil level, oil pressure sensor, and oil pump.
HIGH TEMPHigh engine temperature detected.Check coolant level, radiator, fan, and temperature sensor.
VOLTVoltage anomaly (over/under voltage) on generator or mains.Check generator output, AVR, or mains supply.
EMERG STOPEmergency stop button activated.Reset the emergency stop button.

If the issue persists after performing the suggested actions, consult a qualified technician or the manufacturer's support.

7. Specifications

  • Model: DKG105
  • Type: Microprocessor-based digital genset controller
  • Panel Cutout: Standard 72x72mm
  • Input Voltage Monitoring: 3-phase mains voltage
  • Outputs: Energize to stop, preheat, choke, fuel solenoid, crank, auxiliary
  • Display: Digital engine run-hours, 3-digit LED
  • Adjustments: Digitally adjustable timers and threshold levels
  • Relay Configuration: Programmable
  • Dimensions (Approximate Package): Length 24 cm x Width 15 cm x Height 13 cm
  • Weight (Approximate Package): 0.4 kg
  • Electrified Status: No (Refers to being a control unit, not a power source)
  • Origin: Mainland China

8. User Tips

  • Check Package Contents: Upon receiving the DKG105, verify that all components, including the controller and its pluggable terminal blocks, are present and undamaged.
  • Current Limits: For specific details on maximum charging current or other electrical limits, always refer to the official product datasheet or contact the manufacturer. This information is crucial for safe and correct integration into your system.
  • Wiring Diagrams: Always use a detailed wiring diagram specific to your generator and application when connecting the DKG105 to ensure proper functionality and safety.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or the manufacturer directly. Keep your purchase records handy when seeking support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.