1. Product Overview
The GuliKit TMR Electromagnetic Joystick NS51 is designed as a direct replacement and repair component for various game controllers. Utilizing Tunnel Magnetoresistance (TMR) technology, these joysticks offer enhanced durability and precision compared to traditional carbon film joysticks.
Key features include:
- Direct replacement installation without requiring circuit modifications.
- Low power consumption, similar to carbon film joysticks.
- Unique structural design to prevent interference from magnetic triggers.
- High durability and long lifespan due to contactless and wear-free TMR sensor.
- KK Ring Joystick Cap for easy stick cap replacement.
- Super smooth operation.
Important: This kit is intended for repair use on game controllers only.
2. Compatibility
The GuliKit TMR Electromagnetic Joystick NS51 is compatible with the following controllers:
- PS4 Controller
- PS5 Controller
- Switch Pro Controller (Note: Switch Pro only supports the latest systems)
- Xbox Series Controller
Important Compatibility Note:
For PS5 Dualsense Edge Controller, Xbox Elite Controller, and Xbox One Controller, there may be issues after joystick replacement due to the lack of available software/tools for proper joystick calibration. Therefore, it is not recommended to use this product with these specific controllers.
3. Installation Guide
The GuliKit TMR Electromagnetic Joystick NS51 is designed for direct replacement. However, installation requires desoldering and soldering, which should be performed by individuals with appropriate technical skills and tools to avoid damage to the controller.
3.1. Tools Required
- Small Phillips head screwdriver
- Soldering iron
- Desoldering pump or braid
- Fine-gauge insulated wire (for calibration, if needed)
- Tweezers
- Controller calibration software (PC-based)
3.2. Step-by-Step Installation
- Disassemble the Controller: Carefully open your controller, removing any screws and clips necessary to access the joystick modules.
- Remove Original Joysticks: Desolder the existing joystick modules from the controller's circuit board. Ensure all solder points are clean.
- Install GuliKit TMR Joysticks: Place the new GuliKit TMR Electromagnetic Joysticks onto the circuit board, aligning the pins. Solder them securely in place.
- Prepare for Calibration (if necessary): For certain controllers, an insulated wire may need to be installed from the 1.8-volt line to a test point on the circuit board to enable calibration. This allows the controller to be written for calibration. This wire can be left in place for future recalibration.
- Reassemble the Controller: Carefully reassemble the controller, ensuring all components are correctly seated and screws are tightened.
3.3. Calibration
After installation, it is crucial to calibrate the joysticks to ensure optimal performance and prevent drift. This typically involves connecting the controller to a PC and using a dedicated calibration tool.
- Connect your controller to a PC.
- Open the appropriate controller calibration software.
- Follow the on-screen instructions to calibrate the stick center and stick range. This usually involves moving the joysticks through their full range of motion.
- Save the changes permanently and reboot the controller if prompted.
Refer to the video below for a visual guide on the installation and calibration process:
4. Operating Instructions
Once installed and calibrated, the GuliKit TMR Electromagnetic Joysticks are ready for use. They are designed to provide a superior gaming experience with:
- Super Smooth Movement: Experience precise and fluid control during gameplay.
- No Dead Zone: The TMR sensor technology eliminates dead zones, ensuring immediate response to even the slightest input.
- Enhanced Accuracy: The contactless design provides consistent and accurate input over time.
5. Maintenance
The GuliKit TMR Electromagnetic Joysticks are designed for high durability and long life, requiring minimal maintenance. The contactless and wear-free TMR sensor technology reduces the need for frequent servicing.
- Joystick Cap Replacement: The joysticks feature a KK Ring design, allowing for easy replacement of stick caps if they become worn or if you wish to customize them.
- Cleaning: Periodically clean the exterior of your controller and joystick caps with a soft, dry cloth. Avoid using harsh chemicals or abrasive materials.
6. Troubleshooting
If you encounter issues after installing the GuliKit TMR Electromagnetic Joysticks, consider the following troubleshooting steps:
- Joystick Drift: If the joystick exhibits drift, it is likely a calibration issue. Re-perform the calibration steps outlined in Section 3.3. Ensure the controller is connected to a PC and the calibration software is used correctly.
- Incompatibility: Verify that your controller is listed as compatible in Section 2. As noted, PS5 Dualsense Edge, Xbox Elite, and Xbox One controllers are not recommended due to potential calibration problems.
- Installation Errors: Double-check all soldering points and connections. Ensure no wires are loose or short-circuiting. If you are unsure about the installation, consider seeking professional assistance.
- Magnetic Interference: The unique structural design of the GuliKit TMR joysticks is intended to prevent interference from magnetic triggers. If you suspect interference, ensure the joysticks are correctly seated and there are no foreign objects causing obstruction.
7. Specifications
| Attribute | Value |
|---|---|
| Brand Name | GuliKit |
| Model Number | NS51 |
| Compatible Brand/Model | Sony (PLAYSTATION4, PS5), Nintendo (Switch Pro), Microsoft (Xbox Series) |
| Accessories Type | Accessory Kits |
| Control Method | Touch |
| Cable features | Without cable |
| Reusability | Reusable |
| Origin | Mainland China |
| Bluetooth range | 0 (Not Bluetooth enabled for the joystick module itself) |
| Electric | No |
| Electronic | No |
| Portable | Yes (as a component) |
The GuliKit TMR Electromagnetic Joystick utilizes advanced TMR (Tunnel Magnetoresistance) technology, which was first applied to computer hard drives in 2004. GuliKit first applied this technology to game controller joysticks in 2024, resulting in lower power consumption and higher temperature stability.
8. User Tips
- Professional Installation Recommended: While direct replacement, the installation involves soldering. If you are not confident in your soldering skills, consider having the joysticks installed by a professional to ensure proper function and avoid damaging your controller.
- Ensure Proper Calibration: After installation, always perform the calibration steps. This is critical for eliminating drift and achieving the "super smooth" and precise control the TMR joysticks are designed for.
- Check Compatibility Carefully: Before purchasing, double-check the compatibility list. Using these joysticks with unsupported controllers (e.g., PS5 Dualsense Edge, Xbox Elite, Xbox One) may lead to unresolvable calibration issues and unsatisfactory performance.
- High Quality Product: Users frequently praise the high quality and original nature of the GuliKit TMR joysticks, noting their effectiveness in resolving common joystick issues like drift.
9. Warranty and Support
For specific warranty information, please refer to the terms provided by your retailer or contact GuliKit directly. Keep your proof of purchase for any warranty claims.
For further technical support or inquiries, please visit the official GuliKit website or contact their customer service channels.