1. Introduction
Thank you for choosing the GVDA Smart Digital Multimeter. This manual provides detailed instructions for the safe and effective operation of your GD121 or GD122 multimeter. These devices are designed for measuring AC/DC voltage, AC/DC current, resistance, and continuity. The GD122 model also includes capacitance measurement and live wire detection. Both models feature a clear digital display, backlight, flashlight, NCV (Non-Contact Voltage) detection, data hold, auto power off, and low battery indication.
2. Safety Information
Always observe safety precautions when using this multimeter to avoid electric shock or personal injury. Improper use can also damage the meter or the equipment under test.
- Read and understand all instructions in this manual before use.
- Do not exceed the maximum voltage or current ratings specified for the meter.
- Always disconnect power to the circuit before measuring current or resistance.
- Use caution when working with voltages above 30V AC RMS, 42V peak, or 60V DC. These voltages pose a shock hazard.
- Ensure the test leads are in good condition and properly seated in the correct input jacks.
- Do not use the meter if it appears damaged or if the protective cover is removed.
- Replace batteries immediately when the low battery indicator appears to ensure accurate readings.
- Keep fingers behind the finger guards on the test probes during measurements.
3. Product Overview
Familiarize yourself with the components and controls of your GVDA Digital Multimeter.

- NCV Sensor: For non-contact AC voltage detection.
- Flashlight: Illuminates the work area.
- Display: Digital readout for measurements.
- Lighting Button: Activates the display backlight.
- Backlight Button: Controls the display backlight.
- Wake-up Meter: Button to activate the meter from sleep mode.
- HOLD Button: Freezes the current reading on the display.
- Function Dial: Rotary switch to select measurement functions and ranges.
- 10A Jack: Input for high current measurements (up to 10A).
- COM Jack: Common (negative) input for all measurements.
- VΩmA Jack: Input for voltage, resistance, capacitance (GD122), diode, and continuity measurements.

4. Setup
4.1 Battery Installation
The multimeter requires 3 x 1.5V AAA batteries (not included) for operation.
- Ensure the multimeter is turned off.
- Locate the battery compartment cover on the back of the device.
- Use a screwdriver to open the battery compartment.
- Insert three 1.5V AAA batteries, observing the correct polarity (+ and -).
- Replace the battery compartment cover and secure it with the screw.

5. Operating Instructions
Before taking any measurements, ensure the test leads are securely connected to the appropriate input jacks.
5.1 General Operation
- Turn the function dial to the desired measurement mode.
- Connect the test leads to the circuit or component under test.
- Read the measurement value on the display.
- Press the 'HOLD' button to freeze the current reading. Press again to release.
- Use the 'Backlight' button to illuminate the display for better visibility in dim conditions.
- Press the 'Flashlight' button to turn on the built-in flashlight.


5.2 AC/DC Voltage Measurement
- Turn the function dial to the 'V~' (AC Voltage) or 'V-' (DC Voltage) position.
- Connect the red test lead to the VΩmA jack and the black test lead to the COM jack.
- Connect the test probes in parallel across the component or circuit to be measured.
- Read the voltage value on the display.

5.3 AC/DC Current Measurement
- Turn the function dial to the 'A~' (AC Current) or 'A-' (DC Current) position.
- For currents up to 600mA, connect the red test lead to the VΩmA jack. For currents up to 10A, connect the red test lead to the 10A jack. Connect the black test lead to the COM jack.
- Important: Disconnect power to the circuit. Open the circuit and connect the multimeter in series with the circuit.
- Apply power to the circuit.
- Read the current value on the display.
5.4 Resistance Measurement
- Turn the function dial to the 'Ω' (Resistance) position.
- Connect the red test lead to the VΩmA jack and the black test lead to the COM jack.
- Ensure the circuit or component is de-energized.
- Connect the test probes across the component to be measured.
- Read the resistance value on the display.

5.5 Capacitance Measurement (GD122 Only)
- Turn the function dial to the 'μF' (Capacitance) position.
- Connect the red test lead to the VΩmA jack and the black test lead to the COM jack.
- Ensure the capacitor is fully discharged before testing.
- Connect the test probes across the capacitor.
- Read the capacitance value on the display.

5.6 Diode Test
- Turn the function dial to the 'Diode' symbol position.
- Connect the red test lead to the VΩmA jack and the black test lead to the COM jack.
- Connect the red probe to the anode and the black probe to the cathode of the diode.
- The display will show the forward voltage drop. Reverse the probes; an open circuit (OL) reading indicates a good diode.

5.7 Continuity Test
- Turn the function dial to the 'Continuity' symbol position.
- Connect the red test lead to the VΩmA jack and the black test lead to the COM jack.
- Ensure the circuit or component is de-energized.
- Touch the test probes to the two points to be tested.
- If there is continuity (low resistance), the meter will beep and the display will show a low resistance value.

5.8 Non-Contact Voltage (NCV) Measurement
- Turn the function dial to the 'NCV' position.
- Move the NCV sensor (top part of the meter) close to the conductor or outlet.
- The meter will beep and the NCV indicator will light up with increasing frequency as it detects AC voltage.

5.9 Live Wire Detecting (GD122 Only)
- Turn the function dial to the 'Live' position (GD122 only).
- Connect the red test lead to the VΩmA jack and the black test lead to the COM jack.
- Touch the red test probe to the suspected live wire.
- The display will show 'LIVE' and the meter will beep if a live wire is detected.

5.10 Auto Power Off
The multimeter will automatically power off after a period of inactivity to conserve battery life. Press any button or turn the function dial to wake it up.
5.11 Low Battery Indication
A low battery symbol will appear on the display when the battery voltage is low. Replace the batteries promptly to ensure accurate measurements.
6. Specifications
Below are the detailed technical specifications for the GD121 and GD122 models.

| Feature | GD121 | GD122 |
|---|---|---|
| Max Display Value | 1999 Counts | 5999 Counts |
| DC Voltage | 200mV, 2V, 20V, 200V, 600V | 600mV, 6V, 60V, 600V |
| AC Voltage | 200V, 600V | 600V |
| DC Current | 200uA, 2mA, 20mA, 200mA, 10A | 60mA, 600mA, 10A |
| AC Current | N/A | 600mA, 10A |
| Resistance | 200Ω, 2KΩ, 20KΩ, 200KΩ, 2MΩ | 600Ω, 6KΩ, 60KΩ, 600KΩ, 6MΩ |
| Capacitance | N/A | 6000uF |
| NCV (Non-contact AC voltage) | Yes | Yes |
| Live Line Test | N/A | Yes |
| Diode and Continuity | Yes | Yes |
| Backlight | Yes | Yes |
| Flashlight | Yes | Yes |
| Auto Power Off | Yes | Yes |
| Low Battery Indication | Yes | Yes |
| Operating Temperature | 0 ~ 40 °C | 0 ~ 40 °C |
| Dimensions | 147 x 71 x 45 mm | 147 x 71 x 45 mm |
| Weight | Approx. 190g | Approx. 190g |
| Power Supply | 3 x 1.5V AAA batteries | 3 x 1.5V AAA batteries |




7. Maintenance
- Cleaning: Wipe the meter with a damp cloth and mild detergent. Do not use abrasives or solvents.
- Battery Replacement: Replace batteries when the low battery indicator appears.
- Probe Care: Inspect test leads for damage before each use. Replace if insulation is cracked or wires are exposed.
- Storage: Store the meter in a cool, dry place away from direct sunlight and extreme temperatures. Remove batteries if storing for extended periods.
8. Troubleshooting
- No Display/Meter Not Turning On: Check battery installation and ensure batteries are not depleted. Replace if necessary.
- Incorrect Readings: Ensure the correct function is selected for the measurement. Check test lead connections. Verify the circuit is de-energized for resistance/current measurements.
- 'OL' (Overload) Display: The measured value exceeds the selected range. Switch to a higher range if available, or verify the circuit is within the meter's capabilities.
- No NCV/Live Wire Detection: Ensure the NCV/Live function is selected and the sensor/probe is close enough to the AC voltage source.
9. User Tips
- Always double-check your function dial setting before making a measurement to prevent damage to the meter or circuit.
- For precise measurements, especially of small values, ensure good contact between the probes and the test points.
- Utilize the kickstand (bracket design) for hands-free operation, improving safety and convenience.
- The protective cover helps guard against minor impacts and wear; keep it on during use and storage.
10. Warranty and Support
This GVDA Digital Multimeter comes with a 24-month manufacturer's limited warranty for defective items from the date of receipt. Accessories are covered by a 3-month warranty. This warranty does not cover items damaged or misused after receipt.
For technical support, warranty claims, or service inquiries, please contact the seller or the GVDA customer service department through the platform where the product was purchased. Please provide your order number and a detailed description of the issue.