1. Introduction
The GuliKit TMR Electromagnetic Joystick is an advanced replacement module designed to enhance the precision, durability, and longevity of your game controller. Utilizing cutting-edge Tunnel Magnetoresistance (TMR) technology, these joysticks offer a contactless and wear-free solution to common issues like stick drift, providing a super smooth and accurate gaming experience.

2. Key Features
- Direct Replacement: Designed for easy installation without requiring any circuit modifications.
- Low Power Consumption: Features similar low power consumption as traditional carbon film joysticks.
- Anti-Interference: Unique structural design prevents interference from magnetic triggers on the joystick.
- High Durability & Long Life: Achieved through contactless and wear-free TMR sensors.
- KK Ring Joystick Cap: Includes easy-to-replace stick caps.
- Super Smooth: Provides a fluid and responsive control experience.
- Higher Temperature Stability: Ensures consistent performance even under varying conditions.






3. Compatibility
The GuliKit TMR Electromagnetic Joystick (Model NS51) is compatible with a range of popular game controllers. This kit is intended for repair use only.
- For PS4 DualShock Controller
- For PS5 DualSense Controller
- For PS5 DualSense Edge Controller
- For Xbox Series Controller (Series X/S)
- For Xbox Elite Series 2 Controller
- For Switch Pro Controller

Note: These joysticks are NOT compatible with Xbox One controllers.
4. Setup & Installation
The GuliKit TMR Joysticks are designed for direct replacement installation. However, this process requires disassembling your controller and soldering. If you are not comfortable with soldering, it is recommended to seek professional assistance.
4.1 Tools Required (Not Included)
- Small Phillips head screwdriver
- Prying tools (plastic spudgers)
- Soldering iron and solder
- Desoldering wick or pump
- Tweezers
- Insulated wire (for calibration test point, if needed)
4.2 Installation Steps (General Guide)
- Disassemble Controller: Carefully open your controller by removing the necessary screws and prying apart the casing. Refer to specific online tutorials for your controller model.
- Locate Joysticks: Identify the existing joystick modules on the controller's circuit board.
- Desolder Old Joysticks: Using a soldering iron and desoldering tools, carefully desolder and remove the old joystick modules from the PCB.
- Install New Joysticks: Place the new GuliKit TMR Joysticks into position on the PCB, ensuring correct orientation.
- Solder New Joysticks: Solder the new joysticks securely to the PCB. Ensure all pins are properly connected and there are no solder bridges.
- (Optional) Calibration Wire: For some controllers (e.g., PS5 DualSense Edge), an insulated wire may need to be soldered from a 1.8V line to a specific test point on the PCB to enable calibration. This wire can be left in place for future recalibration.
- Reassemble Controller: Carefully reassemble your controller, ensuring all components are correctly seated and screws are tightened.

4.3 Installation Video Guide
Watch this video for a visual guide on the installation and calibration process for DualSense Edge controllers:
5. Calibration
After replacing the joysticks, calibration is essential to ensure optimal performance and eliminate any initial drift or inaccuracies. Please install the controller cases and screws before calibration and testing.
5.1 Calibration Methods by Controller Type
- For Switch Pro Controllers: Go to the Switch console's
Settings>Controllers and Sensors>Calibrate Joysticks, and follow the on-screen instructions. - For PS4 DualShock, PS5 DualSense, and PS5 DualSense Edge Controllers: Use the third-party open-source calibration tool available at test.gulikit.com to calibrate the joysticks.
- For Xbox Series Controllers (Series X/S): Go to the XBOX console or download the "XBOX Accessories" software from the Microsoft Store on PC. Find the "Recalibrate" option and follow the instructions to calibrate the joysticks.

6. Operating Instructions
Once installed and calibrated, your GuliKit TMR Electromagnetic Joysticks will function identically to your original joysticks, but with enhanced precision and durability. Enjoy a smoother, more responsive, and drift-free gaming experience.
7. Maintenance
Due to their contactless and wear-free design, GuliKit TMR Joysticks require minimal maintenance. Avoid exposing the joysticks to excessive moisture or extreme temperatures. If cleaning is necessary, use a dry, soft cloth. Do not use harsh chemicals or abrasive materials.
8. Troubleshooting
8.1 Common Issues & Solutions
- Stick Drift/Inaccurate Input: This is typically resolved by performing a full calibration as described in Section 5. Ensure the controller is fully assembled before calibration.
- Switch Stick Correction Not Reaching Arrow Triangle: If you encounter issues with Switch stick correction, try recalibrating multiple times. Ensure the stick is moved through its full range of motion during calibration.
- No Response After Installation: Double-check all solder points for proper connection and ensure no solder bridges are present. Verify the joysticks are correctly seated.
- Xbox One Incompatibility: These joysticks are not compatible with Xbox One controllers and cannot be calibrated on them. They are designed for Xbox Series X/S and Elite Series 2.
- Xbox Elite 2 Compatibility Issues: While generally compatible, some users may experience nuances. Ensure proper calibration and check for any specific firmware updates for your controller model.
9. Specifications
| Attribute | Value |
|---|---|
| Product Name | GuliKit TMR Electromagnetic Joystick |
| Model Number | NS51 |
| Brand | GuliKit |
| Origin | Mainland China |
| Accessories Type | Accessory Kits |
| Control Method | Push button (for associated controller functions) |
| Enclosure Material | Plastic |
| Reusability | Reusable |
| Package Includes | Joystick x 2, Joystick Cap x 2 |
| Package Weight | 0.068 kg |
| Package Dimensions (L x W x H) | 10cm x 5cm x 5cm |

10. User Tips
- DIY Installation: Many users successfully install these joysticks themselves by following online tutorials and having basic soldering equipment.
- Calibration is Key: Always calibrate the joysticks after installation for optimal performance and to eliminate any potential drift.
- Heat Caution: Be careful with heat during soldering, as the magnetic sensor can be sensitive.
- Check Compatibility: Ensure your controller model is listed as compatible before purchasing. Xbox One controllers are not supported.
- Genuine Product: These are genuine GuliKit TMR joysticks, offering a reliable solution for stick drift.
- Stick Caps: The included KK Ring caps are easy to replace, but you can often use your original stick caps if preferred.
11. Frequently Asked Questions (FAQ)
- Q: Are these joysticks original GuliKit products?
- A: Yes, these are genuine GuliKit TMR joysticks. Many buyers confirm receiving authentic products that perform as expected after calibration.
- Q: Do these work with the PS5 DualSense Edge controller?
- A: Yes, this joystick is compatible with the PS5 DualSense Edge controller. Users report successful installation and smooth performance after proper calibration.
- Q: Can I use these on an Xbox One controller?
- A: No, these joysticks are not compatible with Xbox One controllers and cannot be calibrated on them. They are designed for Xbox Series X/S and Xbox Elite Series 2 controllers.
- Q: How do I calibrate them for PlayStation controllers?
- A: For PS4, PS5, and PS5 DualSense Edge controllers, you can use the third-party open-source calibration tool at test.gulikit.com.
- Q: What is included in the package?
- A: The package typically includes two TMR joystick modules and two replacement stick caps, making it a complete set for dual-stick controller repair.
- Q: Is soldering required for installation?
- A: Yes, soldering is required to replace the existing joystick modules. If you are not experienced with soldering, professional installation is recommended.
12. Warranty & Support
For warranty information and technical support, please refer to the official GuliKit website or contact the seller directly. Ensure you retain your proof of purchase for any warranty claims.