1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your JIKONG JK-B1A8S10P Smart Active Balance Battery Management System (BMS). This advanced BMS is designed to protect and optimize the performance of various battery types, including LiFePO4, Li-ion, and LTO, in configurations from 4S to 8S.
2. Product Features
- Active Balance: Ensures good durability, long life, and stable performance through real-time active energy transfer equalization using a supercapacitor medium (Patent No: ZL 2019 2 0479589.6).
- High Precision: Single cell voltage range of 1V~5V with an equalization accuracy of ±5mV.
- Efficient Balancing: Achieves 2-10A continuous balanced current to maintain battery consistency, improve cruising range, and extend battery life.
- Smart Connectivity: Mobile phone Bluetooth communication with a dedicated APP (Android and iOS) for real-time battery status monitoring.
- Scalability: Supports balanced cascading for battery packs exceeding 24 cells.
- Versatile Compatibility: Suitable for LiFePO4, Ternary Lithium, Lithium Titanate (LTO) and other battery types.
3. Package Contents
Please verify that all items are included in your package:
- 1 x BMS unit (Bluetooth built-in)
- 1 x Temperature sensor (40cm)
- 1 x Balance Wires (75cm)
- 1 x Active Switch (15cm)
- 4 x Cables
- 4 x Screws
- 1 x Heating cable (Only included with BMS models featuring Heat Function, denoted by 'H')
Note on Variants:
- H: Indicates BMS with Heat Function.
- C: Indicates BMS with CANBUS chip built-in.
- Due to varying supported voltage ranges, accessories like RS485, LCD, and other BMS components may not be universally compatible across all B1A8S20P/B2A8S20P models. The Power Board version is consistent. Please select carefully.

Image: JIKONG JK-B1A8S10P BMS and included accessories (Cables, NTC, Switch Wire, Screws)
4. Specifications
The following table details the specifications for the JK SMART ACTIVE BMS series. Please refer to the specific model for exact values.

Image: Detailed Product Specifications Table for JK SMART ACTIVE BMS, including models like B1A8S10P, B1A8S15P, B1A8S20P, B2A8S20P, and B2A8S60P, with parameters such as Number of Battery Strings, Balance Current, Continuous Charge/Discharge Current, Over Charge/Discharge Protection, and other interfaces.
| Attribute | Value |
|---|---|
| Brand Name | JIKONG |
| Type | LIFEPO4 Battery BMS |
| Handware or Smart | SMART BMS |
| Battery Series | 4S 5S 6S 7S 8S |
| Nominal Voltage | 3.2v (lithium battery rated) |
| Continuous Discharge Current | 100A |
| Charging Current | 100A |
| Balance Function | Active Balanced BMS (1A) |
| Charge and Discharge Port | Common Port BMS |
| Function | Overcharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection, Dropout Protection, Over temperature protection, Balance Function, Bluetooth |
| Usage Scenario | Power BMS, Energy Storage BMS, 3C Digital BMS |
| Certification | CE, RoHS |
5. Setup and Installation
5.1 General Wiring Diagram
Refer to the diagram below for the general connection of the BMS to your battery pack, controller, and charger.

Image: General wiring diagram showing connections for B- (Total Negative), B+ (Total Positive), P- (Load/Charge Negative), Controller, and Charger.
5.2 5-Step Wiring Method (Balance Wires)
Follow these steps carefully for connecting the balance wires. This example uses a single series connection, but the principle extends to other series BMS configurations.

Image: Detailed 5-step wiring method for JK BMS, illustrating connection of balance wires to battery cells and the main BMS unit.
- First Wire Connection: Find the P-, B- position of the protection board. Connect the B- corresponding to the black row of wires, defined as the first wire. Note: The cable is not inserted into the protection board; pay attention to the front and back of the cable.
- Total Negative Terminal: Find the total negative terminal of the battery pack. This is the first string of batteries, and the total positive terminal is the last string. For 18650 Carp battery packs, ensure different battery packs have different positive and negative positions. The multimeter measurement shall prevail. Total Voltage = Number of Strings * Voltage of Single String Battery.
- Connect Balance Wires: Connect the first wire to the negative terminal of the first series of batteries, the second wire to the positive terminal of the first series of batteries, the third wire to the positive terminal of the second series of batteries, the fourth wire to the positive terminal of the third series of batteries, and so on. Note: The wires must be connected in order; do not jump the number of strings.
- Measure Voltage: In the head of the line from the first line to measure the voltage between each of the two lines. From the head of the line to measure out the voltage (ternary batteries in the 3V-4.2V, iron batteries in the 2.5-3.6V). If the measurement of the voltage is outside the range, it represents an incorrect connection. The wrong line must be connected to the right before you can plug into the protection board. Note: If the wires are connected wrongly, they may burn up when plugged into the protection board!
- Final Connection: After confirming that the wires are connected correctly, connect B- to the total negative terminal of the battery (wire length within 15cm is good), then insert the connected wires. Measure the protection board B- and the total positive voltage. This should be equal to the total positive voltage of the P- and equal to the total positive voltage, representing that it has been wired correctly. Finally, the P- welding charging and discharging interface negative terminal total positive terminal connected to the charging and discharging interface positive terminal.
5.3 BMS Interface Overview
The BMS features several interfaces for various functions:

Image: Diagram showing the various interfaces on the BMS unit, including Temperature sensor, RS485, LCD, Heat Function, and CANBUS.
- Temperature Sensor: For monitoring battery temperature.
- RS485 Interface: All JK BMS models are configured with RS485 function by default.
- LCD Interface: All JK BMS models are configured with an LCD interface by default (except JK-BD4A17S4P).
- Heat Function Interface: For models with heating functionality (customizable).
- CANBUS Interface: Requires customization.
5.4 Heating Function Instructions
For BMS units equipped with the heating function:
- The green 5PIN cable of the heating cable must be linked to the heating pad.
- The remaining black and red cables are linked to the smart charger.
- After the smart charger links the BMS, it detects the battery temperature through the BMS, automatically monitoring the charging status of the battery.
- Heating Logic: If the battery temperature falls below the low-temperature charge protection threshold (settable in the APP), charging will be turned off, and heating will be activated.
- The heating power depends on the battery voltage and the resistance value of the heating film.
- The BMS includes 1 internal and 2 external temperature sensors to detect battery temperature.
5.5 Parallel Operation
If you intend to use multiple BMS units in parallel:

Image: Diagram illustrating the parallel connection of LiFePO4 batteries, each with its own BMS, connected to bus bars via Fast Class T Fuses.
- A Fast Class T Fuse must be added to each individual battery pack.
- Alternatively, a discharge diode (high power diode selected according to load) can be used.
6. Operating Instructions
6.1 Mobile APP Usage
The JIKONG BMS supports mobile phone Bluetooth communication for real-time monitoring and configuration.
- Bluetooth Link Name: JIKONG BMS
- iOS Download: Search for "JIKONG BMS" in the APP STORE.
- Android Download: Visit https://www.pgyer.com/Cfq3

Image: Screenshots of the JIKONG BMS mobile application interface, showing battery cell voltages, balance status, and various settings.
7. Safety Information and Protections
The JIKONG Smart BMS is equipped with six key security protections to ensure the safe operation and longevity of your battery system:

Image: Diagram illustrating the six security protection features of the BMS.
- Overcharge Protection: Prevents over-charging, which can affect battery life.
- Short Circuit Protection: Automatic protection when a short circuit occurs.
- Over Discharge Protection: Prevents the battery from running out completely.
- Overcurrent Protection: Prevents the current from exceeding the battery's safe range.
- ALL-IN Protection (Dropout Protection): Prevents cable drop or poor contact.
- Over Temperature Protection: Prevents the battery from overheating.
8. Troubleshooting
This section addresses common issues and their solutions.
8.1 No Power On
- Ensure the last "B+" line is connected to the battery's total positive pole.
- Perform a charge activation: Ensure the charger voltage is more than 4V above the battery pack voltage to activate the BMS.
- Check if the charger has voltage output.
8.2 Voltage Inaccuracy
- Measure the actual total voltage of the battery pack with a multimeter.
- Enter this actual total voltage into the "Voltage Calibration" setting within the APP.
8.3 Current Inaccuracy
- Ensure both BMS B- and P- are connected with two 7AWG wires in parallel. Failure to do so may lead to current errors.
- Use a clamp meter to measure the actual current of the battery pack.
- Enter this actual current into the "Current Calibration" setting within the APP. Higher actual current values lead to higher calibration accuracy.
8.4 Capacity Inaccuracy
- Set Battery Capacity: First, set the battery capacity in the APP. You can set it slightly larger than the actual capacity (e.g., for a 100AH battery, set to 120AH or 150AH).
- Discharge: Discharge the battery using an electric instrument until the protection board prompts single undervoltage protection.
- Charge: Charge the battery continuously without interruption until the BMS prompts single-unit over-voltage protection.
After completing these steps, the capacity will automatically update in the APP, showing the actual battery capacity, and the State of Charge (SOC) will also be accurate.
8.5 Mismatch in Number of Strings
- Check if the "number of single unit" parameter is set correctly in the APP settings.
- If there is no voltage in the middle of 2S or more strings, check whether the collection line is disconnected or loose.
9. User Tips
- Charger Selection: Always use a special charger designed for your battery type (e.g., Carp batteries require a specific Carp battery charger). Using a lead-acid battery charger can damage the BMS. For ferrous batteries, charger voltage = 3.65V * number of battery strings. For ternary batteries, charger voltage = 4.25V * number of battery strings.
- BMS Current Rating: The BMS current rating should be chosen based on the current limit of your controller, which in turn depends on your motor's power. For example, a 64V, 1000W motor draws 15.6A (1000W/64V). The controller's current limit must be greater than 15.6A, and the BMS current limit must be greater than the controller's limit. Always leave a margin for safety and performance.
- Wiring Order: Always follow the specified wiring order for balance leads to prevent damage to the BMS. Double-check all voltage readings before making final connections.
10. Support
For any further assistance, technical support, or inquiries not covered in this manual, please contact the seller or manufacturer directly. Ensure you have your product model and purchase details ready for efficient service.