EVCO EV3X21N7

Contents

EVCO EV3X21N7 Temperature Controller Thermostat User Manual

Model: EV3X21N7 | Brand: EVCO

1. Introduction

The EVCO EV3X21N7 is a compact and versatile temperature controller designed for various industrial and commercial refrigeration applications. It features a single relay output for compressor control and a configurable analog/digital input for temperature sensing. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your EV3X21N7 controller.

2. Safety Information

WARNING: Electrical shock hazard. Installation and maintenance should only be performed by qualified personnel. Disconnect power before servicing.

  • Ensure the power supply matches the controller's specifications (230V 50/60Hz).
  • Do not expose the device to water or excessive humidity.
  • Verify all wiring connections are secure and correct before applying power.
  • Adhere to all local electrical codes and regulations.

3. Specifications

FeatureSpecification
ModelEV3X21N7
Power Supply230V AC, 50/60Hz
Compressor Relay Output1 x 16A (resistive load) @ 250V AC, Max 10A
Analog/Digital Input1 configurable input
Probe TypeNTC/PTC (probe not included)
Dimensions (WxHxD)75 x 33 x 39.5 mm
Panel Cut-out71 x 29 mm
ConnectionsScrew terminals
FeaturesEnergy saving function
DIY Supplies CategoryElectrical
Article Number00702140

4. Installation and Wiring

The EV3X21N7 controller is designed for panel mounting. Ensure the panel cut-out dimensions are 71x29 mm. Secure the controller using the provided mounting clips.

4.1 Wiring Diagram

Refer to the diagram below for correct electrical connections. All wiring should be done with the power supply disconnected.

EVCO EV3X21N7 Wiring Diagram
Figure 1: EVCO EV3X21N7 Temperature Controller with Wiring Diagram

4.2 Terminal Connections

The controller uses screw terminals for connections. Ensure all wires are properly stripped and securely fastened.

  • Terminals 1, 2, 3 (CAB / DIG): These terminals are for the NTC/PTC temperature probe (not included) or a configurable digital input. Connect the probe according to its specific instructions.
  • Terminals 6, 7 (L, N): Connect the main power supply (230V AC, 50/60Hz) to these terminals. Terminal 6 is Live (L) and Terminal 7 is Neutral (N).
  • Terminals 8, 9 (K1 Relay): These are the contacts for the compressor relay output. Connect your compressor's power circuit through these terminals. Ensure the load does not exceed 16A.
  • Terminal 10 (N): This is an additional Neutral connection point, often used for the compressor's neutral line if it's separate from the main power neutral.
EVCO EV3X21N7 Front Panel
Figure 2: Front Panel of EVCO EV3X21N7 Controller

5. Operating Instructions

The EV3X21N7 features a clear digital display and intuitive buttons for operation.

5.1 Front Panel Controls

  • SET Button: Used to enter parameter setting mode and confirm selections.
  • Power Button (⑁): Turns the controller ON/OFF or enters standby mode.
  • Up (▲) / Down (▼) Buttons: Used to navigate menus and adjust parameter values.
  • Light Button (☀): May control internal light or other auxiliary functions depending on configuration.

5.2 Setting the Temperature

To set the desired temperature (setpoint):

  1. Press the SET button. The current setpoint value will flash on the display.
  2. Use the Up (▲) or Down (▼) buttons to adjust the setpoint to your desired temperature.
  3. Press the SET button again to confirm the new setpoint and exit the setting mode.

5.3 Energy Saving Function

The controller includes an energy saving function. Consult the full technical manual (if available from EVCO) for details on how to activate and configure this feature to optimize power consumption.

6. Maintenance

Regular maintenance ensures optimal performance and longevity of your EV3X21N7 controller.

  • Cleaning: Periodically clean the front panel with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Inspection: Annually inspect all wiring connections for tightness and signs of wear or corrosion.
  • Probe: Ensure the temperature probe is clean and correctly positioned for accurate readings.
  • Ventilation: Ensure adequate ventilation around the controller to prevent overheating.

7. Troubleshooting

If you encounter issues with your EV3X21N7 controller, refer to the following common problems and solutions:

ProblemPossible CauseSolution
Display is blankNo power supply; loose wiringCheck power connections (Terminals 6, 7); ensure power is supplied.
Incorrect temperature readingFaulty probe; incorrect probe wiring; probe not in correct locationCheck probe connections (Terminals 1, 2, 3); replace probe if necessary; reposition probe.
Compressor not turning ON/OFFIncorrect setpoint; relay fault; wiring issue to compressorVerify setpoint and differential settings; check wiring to compressor (Terminals 8, 9); consult a technician if relay is suspected faulty.
Controller unresponsiveSoftware glitch; internal faultTry power cycling the device. If problem persists, contact support.

8. User Tips

  • Probe Placement: For accurate temperature control, ensure the NTC/PTC probe is placed in a location that truly represents the temperature of the environment you wish to control, away from direct airflow or heat sources.
  • Parameter Lock: Many EVCO controllers have a parameter lock feature to prevent accidental changes. Familiarize yourself with this feature to secure your settings once configured.
  • Documentation: Keep this manual and any additional technical documentation provided by EVCO in a safe place for future reference.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your original point of purchase or an authorized EVCO distributor. Ensure you have your product model (EV3X21N7) and any relevant purchase details available when seeking support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.