1. Introduction
Thank you for purchasing the Forubest Ewelink Zigbee Smart Button Scene Switch. This device is designed to enhance your smart home experience by providing a convenient way to trigger various scenes and control Zigbee-compatible devices with a simple press. Please read this manual carefully before use to ensure correct operation and to avoid any damage to the product.
Note: This product requires a Zigbee gateway (such as ewelink Zigbee hub or Zigbee2MQTT) to function.
2. Specifications
| Feature | Specification |
|---|---|
| Product Name | Smart Button / SOS Button |
| Model Number | ZG-102ZE |
| Brand Name | Forubest |
| Wireless Protocol | Zigbee 3.0 |
| Working Voltage | 3V |
| Battery Type | CR2032 (included) |
| Standby Current | <8uA |
| Working Temperature | -10°C ~ 55°C |
| Working Humidity | 0% ~ 99% RH |
| Control Distance | 30m (open area) |
| Dimensions | Φ50 x 13mm |
| Life Cycle (Battery) | 1 Year (general use) |
| Compatibility | All Compatible (requires Zigbee hub) |
| Certification | CE, FCC, RoHS |
| Camera Equipped | No |
| Origin | Mainland China |
3. Setup
3.1. Battery Installation
- Rotate the back cover of the Smart Button counter-clockwise to open it.
- Insert the CR2032 battery into the battery holder, ensuring the correct positive (+) and negative (-) terminals are aligned.
- If installing for the first time, remove any insulation sheet present. The indicator light will illuminate for 3 seconds, confirming power-on.
- Replace the back cover and rotate clockwise to secure it.
3.2. Network Configuration (Pairing)
To integrate the Smart Button into your smart home system, it must be paired with a Zigbee gateway.
- Ensure your Zigbee gateway is powered on and connected to your home network.
- Open your smart home application (e.g., Ewelink App) and navigate to the "Add Device" interface.
- Select your Zigbee Gateway within the app and initiate the "Search Device" function. (Refer to your Zigbee Gateway/App manual for specific instructions).
- On the Smart Button, press and hold the button for 10 seconds. The indicator LED will flash rapidly, indicating that the device has entered network configuration mode.
- Wait for the app to confirm successful pairing.
4. Operating Instructions
The Smart Button supports three types of press actions, each configurable to trigger different smart scenes or control devices through your smart home app:
- Single Press: A quick, momentary press of the button.
- Double Press: Two quick, consecutive presses of the button.
- Long Press: Press and hold the button for more than 3 seconds.
Each button operation will cause the indicator light to flash once.
4.1. Creating Smart Scenes
To utilize the Smart Button, you need to create automation rules or scenes within your smart home application (e.g., Ewelink App). These scenes link a button action to a desired outcome, such as turning lights on/off, adjusting thermostats, or activating an 'away mode'.
4.2. Example Scenarios
- Away Mode: Configure a double press to turn off all your lights, air conditioners, fans, and other electronic devices when leaving your home.
- Lighting Control: Use a single press to power on or off a Zigbee bulb in remote mode.
- Custom Scenes: Create any smart automation you desire, such as a 'Home Mode' to activate specific devices upon arrival.
5. Maintenance
5.1. Cleaning
Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents.
5.2. Battery Replacement
When the battery is low, the device's performance may be affected. Replace the CR2032 battery by following the steps in Section 3.1. Battery Installation.
6. Troubleshooting
- Device not responding: Check if the battery is correctly installed and has sufficient charge. Ensure the device is within range of the Zigbee gateway.
- Cannot pair with gateway: Make sure the gateway is in pairing mode. Try resetting the Smart Button by removing and reinserting the battery, then attempt pairing again. Ensure you are holding the button for the required 10 seconds during pairing.
- Scenes not activating: Verify that the scenes are correctly configured in your smart home app and that the linked devices are online and functional.
- Indicator light not flashing: This could indicate a dead battery or a device malfunction. Replace the battery first.
7. User Tips
- The compact design allows the button to be placed on a table or hung on a wall for easy access.
- Experiment with different button press combinations (single, double, long) to create intuitive controls for various daily routines.
- Consider using the long press function for less frequent but important actions, like an 'all off' or 'emergency' scene.
8. Warranty and Support
For information regarding warranty, returns, or technical support, please refer to the seller's policies or contact their customer service directly. Keep your purchase receipt for warranty claims.