VDIAGTOOL V500PRO

Contents

VDIAGTOOL V500PRO Automotive Circuit Tester User Manual

Model: V500PRO

1. Safety Information

To ensure your safety and prevent damage to the device or vehicle, please carefully read and follow all instructions in this manual before use.

When operating the device, always verify proper testing procedures and strictly adhere to the instructions provided. As automotive electrical systems may vary, you must assess potential risks and ensure a safe testing environment.

Always observe all safety warnings, use appropriate tools, and disconnect power sources when necessary. Improper operation may result in personal injury, equipment damage, or voided warranty.

Safety Messages

Safety messages use standardized signal words to indicate hazard levels and prevent injuries or equipment damage:

▲ DANGER

Will result in death or serious injury if ignored
Indicates an immediately life-threatening hazard.

▲ WARNING

Could result in death or serious injury if ignored
Indicates a potentially dangerous situation.

Safety Instructions

This manual covers known safety hazards, but cannot anticipate all possible risks. You are responsible for ensuring safe operating conditions and procedures.

▲ DANGER

  • Always ventilate the service area when engine is running or use building exhaust removal system if available.
  • Carbon monoxide is odorless and deadly - can cause loss of consciousness or death.

▲ WARNINGS

  • Always keep a fire extinguisher suitable for gasoline, chemical, and electrical fires nearby.
  • Never operate or observe the tool while driving—distraction can lead to fatal accidents.
  • Keep clothing, hair, hands, tools, and test equipment away from moving or hot engine parts.
  • Perform automotive testing only in a safe, controlled environment.
  • Ensure proper ventilation—exhaust gases are poisonous.
  • Never connect or disconnect test equipment while the ignition is ON or the engine is running.
  • Place wheel chocks in front of drive wheels and never leave the vehicle unattended during testing.
  • Wear ANSI-approved safety eye protection at all times.
  • Exercise extreme caution around ignition coils, distributor caps, spark plugs, and wires—high voltage is present when the engine is running.
  • Before testing, ensure the transmission is in P (A/T) or Neutral (M/T) and the parking brake is engaged.
  • Keep the scan tool clean and dry; avoid contact with oil, water, or grease. Clean only with a mild detergent and soft cloth.
  • Do not modify, disassemble, or expose the tool to extreme temperatures or moisture.
  • This tool is not a substitute for professional diagnostic equipment—use with caution.
  • The manufacturer is not liable for damages caused by misuse, negligence, or unauthorized modifications.

2. Product Overview

The VDIAGTOOL V500PRO is an intelligent automotive electrical system circuit tester and breaker finder tool designed for 9V-30V vehicle electrical systems. It features a 2.36-inch large LCD screen that can be folded up to 90° for optimal viewing angles.

This all-in-one tool combines multiple functions including a smart power probe, multimeter, oscilloscope, relay test, fuel injector test, component activation, and a short/open circuit finder.

VDIAGTOOL V500PRO kit with various cables and probes, showing 0.1-100V test, 0-5V output, component activation, and circuit breaker finder features.
Figure 2.1: VDIAGTOOL V500PRO Product Kit Overview
Diagram showing all-in-one features of VDIAGTOOL V500PRO including locating open circuit, voltage test, resistance test, negative test, multimeter mode, oscilloscope mode, 0-5V power supply, component test, relay test, injector test, trailer lights test, and self test.
Figure 2.2: All-in-One Features of V500PRO

Keypad Introduction

The device features a 6-key navigation system for fast operation:

  • ESC button: Returns to the previous screen. For other tests, press ESC button once to exit.
  • OK button: Confirm key.
  • Up button: Navigation key or voltage output, numerical adjustment.
  • Left button: Navigation key.
  • Right button: Navigation key.
  • Down button: Navigation key or voltage output, numerical adjustment.

Accessories Included

  • V500 Pro Circuit Tester × 1
  • V500 Pro Breaker Finder × 1
  • Probe Tip × 1
  • Fine Probe Tip × 1
  • Probe Tip Extension Cable × 1
  • Wire Piercing Probe × 2
  • Banana to Banana Plug Test Lead × 2
  • Fuse × 3
  • Relay Test Cable × 1
  • Alligator Battery Clip × 1
  • Type-C Data Cable × 1
  • User Manual × 1
  • Banana Plug to Alligator Clip × 1

3. Setup and Initial Connection

Before using the VDIAGTOOL V500PRO, ensure all components are present and in good condition. The device is powered by connecting to the car battery or cigarette lighter.

Connecting the Device

  1. Connect the red positive wire to the positive terminal of the vehicle's 12V/24V battery.
  2. Connect the auxiliary ground lead (black clip) to a good ground point on the vehicle chassis or the negative terminal of the battery.
  3. Ensure the device is securely connected before proceeding with any tests.
Video 3.1: Demonstrates the initial setup and connection of the V500PRO to a vehicle battery for various tests.

4. Operating Instructions

The V500PRO offers various testing modes accessible via the main menu. Use the navigation keys (Up, Down, Left, Right) and OK/ESC buttons to navigate and select functions.

4.1 Smart Test

This mode automatically recognizes the measured signal (voltage or resistance) without manual mode switching. It includes Voltage Test, Resistance Test, and Positive/Negative Test.

  • Voltage Test: When the auxiliary ground lead is connected to ground, touching the Probe Tip to a voltage signal will display the DC voltage (VDC) and battery supply voltage (VCC).
  • Resistance Test: Connect the auxiliary ground lead to one end of a resistance and the Probe Tip to the other end to display resistance values.
  • Positive/Negative Test: A red LED indicates positive voltage deviation (±0.8V from power supply), while a green LED indicates negative voltage. The speaker will sound regularly.
V500PRO screen displaying multimeter parameters like voltage, resistance, diode, current, frequency, and polarity.
Figure 4.1: Multimeter Mode Display

4.2 Multimeter Mode

This feature measures multiple electrical properties. Use the Left/Right buttons to select the desired test mode:

  • Voltage (VDC): Connect the probe clip to the negative pole and the probe tip to the measured voltage.
  • Resistance (OHM): Connect the probe clip to one side of the resistance and the probe tip to the other.
  • Diode (DIO): Connect the probe clip to one side of the diode and the probe tip to the other. Displays voltage and polarity.
  • Current (AMP): Connect the probe in series in the circuit to display current.
  • Frequency (HZ): Displays frequency and duty cycle.
  • Polarity: Displays whether the measured line is positive or negative.

4.3 Oscilloscope Mode

This mode displays electrical signals graphically as Voltage (Y-axis) versus Time (X-axis). It can be displayed in vertical or transverse screen.

  • Y-axis: Shows voltage from 0.0V to 10.0V.
  • X-axis: Shows time from 1ms to 500ms.

NOTE: Press the "OK" button to pause or run waveform refresh.

V500PRO screen displaying an oscilloscope waveform with voltage, pulse width, frequency, and duty cycle parameters.
Figure 4.2: Oscilloscope Mode Display with waveform tips.

4.4 0-5V Power Supply

This feature provides a regulated and stable 0-5V DC output voltage, commonly used for low-power electronic devices. It is an active mode, allowing adjustment of voltage output under 5V and limiting current to 100mA to prevent burning out components.

V500PRO screen showing 0-5V power supply output voltage and set value, with a connected LED light.
Figure 4.3: 0-5V Power Supply Function

4.5 Component Activation

This feature allows you to activate components directly to verify their functionality. It is designed for supplying power or ground, not for sensitive electronics.

Activating Components in Your Hand

  1. Hook up the battery clip to power supply.
  2. Enter into Active, select MOMENT mode function.
  3. Connect the auxiliary ground lead to the negative terminal of the component, and the probe tip to the positive terminal. Press the "Up" button to trigger activation.
  4. The LCD screen will display VDC, AMP, and VCC values.

Activating Components in Vehicle

Importance: The activation mode is only for power/ground supply and should not be used for sensitive electronics (ECU, sensor module) to avoid damage. Always refer to the vehicle manufacturer's schematic diagram.

  1. Hook up the battery clip to power supply.
  2. Enter into Active, select MOMENT mode function.
  3. Connect the auxiliary ground lead to the negative terminal of the component, and the probe tip to the positive terminal. Press the "Up" button to trigger activation.
  4. The LCD screen will display VDC, AMP, and VCC values.

If the probe circuit breaker trips or displays "OVERLOADED", it means the probe is overloaded due to direct ground, negative voltage, a short-circuited component, or a very high current component (e.g., starter motor). Adjust the overload current value (1A-18A) in SETTING mode and repeat.

Images showing various automotive components like lights, fuel injectors, windshield wipers, motors, radiator fans, and air conditioning fans being activated.
Figure 4.4: Examples of Component Activation

4.6 Relay Test

This feature checks the function and performance of relays, including 4-terminal and 5-terminal relays. It displays the power supply voltage (VCC) and provides diagrams for wiring connections.

  1. Select "Relay" from the main menu.
  2. Connect the relay test cable to the Relay Test Port (9) on the device.
  3. Connect the relay to the test cable according to the displayed diagram (4-terminal or 5-terminal).
  4. Press the "Up" button to start the test.
  5. Press "OK" to view wiring connection diagrams.
V500PRO screen showing relay test interface with VCC voltage and diagrams for 4-terminal and 5-terminal relays.
Figure 4.5: Relay Test Interface and Diagrams

4.7 Fuel Injector Test

This feature uses the probe tip to output different pulse signals to the injector and check its spraying status. This helps diagnose injector conditions without needing a garage visit.

Signal Output Modes:

  • Mode 1: 1 pulse with 250ms positive pulse width.
  • Mode 2: 7ms positive, then 20ms negative, cycle 1.4s.
  • Mode 3: 4ms positive, then 10ms negative, cycle 1.4s.
  • Mode 4: Continuous output of 7ms positive, then 20ms negative.

Injector Test Procedure:

  1. Turn off the vehicle's engine.
  2. Connect the BLACK clip to the negative terminal of the battery and the RED clip to the positive terminal.
  3. Unplug the connector from the fuel injector. Connect the probe auxiliary ground lead to the negative side of the injector, and the probe tip to the positive side.
  4. Enter the Injector Test function and select the desired test mode.
  5. Press "OK" to trigger the test.
  6. Check the injector spraying status to diagnose the condition.
V500PRO screen showing injector test modes (M1-M4) and an illustration of a fuel injector.
Figure 4.6: Fuel Injector Test Modes

4.8 Locating Circuit Breaker Point, Open Connections, Broken Wires, Current Leaks (Breaker Finder Mode)

The V500PRO can easily locate circuit breaker points, open connections, broken wires, and current leaks with tone changes, and trace wires/cables without damaging insulation. This is done in Mode II.

How to use the Breaker Finder:

The probe is made of coiled steel and can be bent. For best results, position the probe tip (black cap) perpendicular (at 90°) to the wire being traced, either above or below it.

Setting Sensitivity Level:

Turn the rotary switch of the circuit breaker finder clockwise to increase sensitivity, and anticlockwise to decrease it.

Breaker Finder Operation Guide:

  1. With the probe kit connected to power, select Mode II on the tool kit working mode switch button.
  2. Switch on the Short Open Circuit Finder and set the rotary switch to the middle position.
  3. Press and hold the TEST button and move the black probe tip along the wire you want to test. The finder will detect the signal and sound the loudspeaker.
  4. Connect the black test lead to negative supply (ground) and red test lead to positive supply (or a fuse socket).
  5. Switch on the finder probe and set its rotary switch to the middle position. Press and hold the TEST button and slowly sweep the wire with the probe point above or below perpendicularly and as close as possible.
  6. Check at different points of the wire to narrow down the location or trace the wire all along.
  7. Observe the tone signal. Where the tone stops, it's the location of the open, break, or bad connection. Increase sensitivity if needed.
  8. After locating the open circuit, disconnect the test leads and release the TEST button.
Images showing the V500PRO being used for checking short circuits, locating open circuits, and wire tracing in a vehicle engine bay.
Figure 4.7: Circuit Diagnostic Functions (Short Circuit, Open Circuit, Wire Tracing)

4.9 Other Features

  • 90° Foldable Screen: Allows real-time data viewing at different angles.
  • High Brightness Searchlight: LED lights illuminate dark working environments.
  • Overload Protection: Protects the device from damage.
  • LED Indicator & Buzzer Reminder: Provides visual and audible feedback.
  • 2.4" Color LCD FTF Screen: Clear display for data.
  • Sturdy Case: For protection and portability.
V500PRO showing its high brightness searchlight and 90-degree foldable screen for tight spaces.
Figure 4.8: Foldable Screen and Searchlight Features

5. Maintenance

To ensure the longevity and proper functioning of your VDIAGTOOL V500PRO, follow these maintenance guidelines:

  • Cleaning: Keep the scan tool clean and dry. Avoid contact with oil, water, or grease. Clean only with a mild detergent and a soft cloth.
  • Storage: Store the device in its sturdy case in a dry environment, away from extreme temperatures.
  • Software Updates: The device supports software updates. Regularly check the official website (www.vdiagtool.com/support/downloads) for the newest software version. To update, hold down the 'Down' key and power on the device until it displays 'USB mode', then use the computer software to upgrade.

6. Troubleshooting

Circuit Breaker Tripping / Overload

If the probe circuit breaker trips or the device displays "OVERLOADED", it indicates an overload. This can be caused by:

  • The contact you are probing is a direct ground or negative voltage.
  • The component you are testing is short-circuited.
  • The component is a very high current component (e.g., a starter motor).

Solution: Adjust the overload current value (1A-18A) in the 'SETTING' menu and repeat the operation. Always refer to the component's specifications to set the appropriate overload current value to avoid damage.

Current Testing Issues

When testing current, ensure wires are in series connection, not parallel. Parallel connection can trigger overload protection and restart the device.

Short Open Circuit Finder Safety

The Short Open Circuit Finder LED and LCD draw minimal current (less than 1 milliamp), making it safe for use with computer and airbag systems when used as a test light or multimeter. However, when pressing the switch forward, full battery current is supplied to the probe tip. To prevent power from going to the tip while still using multimeter functions, connect the extra ground lead to the Short Open Circuit Finder and press the power switch forward until it trips the circuit breaker. Press the reset button to restore full power.

7. Specifications

V500 Pro Circuit Tester

ParameterValue
DisplayLCD Display, 2.36-inch TFT Color Screen with 90° Rotation
Operating Voltage9V - 30V DC (for 12V/24V Car Battery Voltage)
Voltage Measurement Range0.1V - 100V
Resistance Measurement Range0KR - 200KR
Operating Temperature0°C - 50°C (32°F - 122°F)
Working Environment Temp0°C - 50°C (32°F - 122°F)
Storage Temperature-20°C - 70°C (-4°F - 158°F)
Power SourceBy Connecting to Car Battery
Cable Length20FT/6M Cable
MaterialPlastics
CertificationsFCC, CE
Software UpdateYes
Wireless SupportNo
Batteries IncludedNo
Supported LanguagesEnglish, Chinese, French, Spanish, German, Russian, Italian, Portuguese, Polish
Vehicle CoverageCar, SUV, Motorbike, Steamer, Truck, Bus

V500 Pro Breaker Finder

ParameterValue
Operating Voltage6V - 42V DC
Operating Temperature0°C - 60°C (32°F - 140°F)
Storage Temperature-40°C to 70°C (-40°F - 185°F)
Power SourceBy a 9V Battery

Product Dimensions & Weight

  • Item Length: 25cm
  • Item Width: 16cm
  • Item Height: 9cm
  • Item Weight: 2.5kg
  • Main line: OD 7.8mm, Length 6m
  • Extension line: OD 4.5mm, Length 1m
  • USB line: OD 3.5mm, Length 0.5m
  • Clip line: OD 4.5mm, Length 0.4m
  • Relay line: OD 4.0mm, Length 0.5m

8. User Tips

  • Check Package Contents: Always verify that all listed accessories, including extra cables and test needles, are present upon receiving your V500PRO kit.
  • Safety First: Before any testing, ensure the vehicle is in a safe state (engine off, parking brake engaged, transmission in P/N).
  • Proper Probe Positioning: For accurate open circuit detection, position the breaker finder's probe tip perpendicular to the wire being traced.
  • Overload Protection: If the device triggers overload protection, adjust the current limit in the settings to match the component's specifications to prevent damage.

9. Warranty and Support

Limited Three Years Warranty

VDIAGTOOL warrants the V500 Pro product against defects in materials and workmanship for thirty-six (36) months from the date of delivery to the original purchaser for commercial or business use. This warranty does not cover damage resulting from misuse, unauthorized modification, improper maintenance, or operation outside specified conditions. VDIAGTOOL's sole liability shall be limited to repair or replacement of defective components at its discretion. Consequential, incidental, or other damages are expressly excluded. Some jurisdictions may not permit certain limitations of liability.

Technical Support

Training Videos

Free product operation videos are available:

  1. Visit Training Center: https://www.vdiagtool.com/support/training-center
  2. Select the "Circuit Testers" category, then watch model-specific tutorials.

Other Contact Information


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.