PDDAXLQUE DX-LRO2

Contents

DX-LRO2 LoRa Transceiver Wireless Module Instruction Manual

Model: DX-LRO2 | Brand: PDDAXLQUE

1. Introduction

The DX-LRO2 LoRa module is a high-performance wireless transceiver designed for long-range, low-power communication. Featuring the ASR6601 SOC chip, it supports UART serial communication and a rich set of AT commands, making it suitable for various IoT applications. This module offers excellent sensitivity and output power, enabling reliable data transmission over significant distances.

DX-LR01-A LoRa Module 433MHz
Figure 1: DX-LR01-A LoRa Module 433MHz

2. Package Contents

The DX-LRO2 Product Set typically includes the following components:

  • DX-LRO2 LoRa Module (quantity may vary by package)
  • USB cable (x2 for developer packages)
  • Rubber rod antenna (x2 for developer packages)
  • USB to TTL Adapter Board (x2 for developer packages)
Video 1: Unboxing and overview of the LR02 module and its components, including the adapter board and antenna.

3. Specifications

3.1. DX-LRO2 LoRa Module

Parameter Value
Chip ModelASR6601 SOC Chip
TypeModule
Module Size36(L)x16.5(W)x4(H)mm
Distance between rows of needles2.54mm
Communication InterfaceLPUART (UART Serial Communication)
AT InstructionSimple AT instruction set available
Frequency Band433-475MHz (LR01/LR02-433T22D), 850-930MHz (LR01/LR02-900T22D)
Transmission MethodTransparent, Fixed-point, Broadcast transmission
Operating Temperature-40°C ~ +85°C
Output Power (Firing Power)0~+22dBm
Supply Voltage (Operating Voltage)3~5.5 V (Typical: 5V for LR01-A, 3.3V for LR01)
Modulation MethodSpread Spectrum Modulation
Receiver Sensitivity-138dBm
RF Input Impedance50Ω
Reference DistanceVisible up to 8km (open), 3.8km (urban)
CertificationsCE, FCC, RoHS, ISO
ConditionNew
CustomizableYes
LR02 Key Features and Dimensions
Figure 2: LR02 Key Features and Dimensions
LR01 Key Features and Specifications
Figure 3: LR01 Key Features and Specifications

3.2. SMA Adapter Cable

Parameter Value
Operating frequency0-6GHZ
Antenna efficiency35-80%
VSWR<1.8
Polarization modeVertical polarization
Antenna interfaceSMA external thread internal hole/IPEX generation
Impedance50Ω
Antenna size120mm
Power capacity33dbm
Operating temperature-30°C ~ 70°C
SMA Adapter Cable Parameters
Figure 4: SMA Adapter Cable Parameters

4. Pinout

The DX-LRO2 module features several pins for power, communication, and control. Understanding the pin definitions is crucial for proper integration.

DX-LR02 Module Pinout, Indicator Light, Antenna Interface, and Module Adapter Board Wiring Diagram
Figure 5: DX-LR02 Module Pinout and Adapter Board

4.1. Module Pin Definitions

Pin Number Pin Name Pin Function
1,3,4,5,9,11,12,13,16,17,18,19,20,23,24,25,26,27GPIO09, GPIO45, GPIO44, GPIO37, GPIO00, GPIO02, GPIO06, GPIO07, GPIO16, GPIO17, GPIO14, GPIO15, GPIO62, GPIO58, GPIO11, GPIO08, GPIO05, GPIO04Programmable input/output pins (IO)
2UART_TXSerial data output
6M1Reserved, Customizable IO port
7M0Reserved, Customizable IO port
8WORK-STATUSModule working status output pin (1s high 1s low)
10AUXModule RF status indication pin
14,28,30GNDPower ground
15VBATPower input pin (3.3V typical value)
21UART_RXSerial data input
22RSTNReset
29ANTAntenna
Detailed Module Pin Definitions Table
Figure 6: Detailed Module Pin Definitions Table

5. Setup

To get started with your DX-LRO2 module, follow these general setup guidelines:

  1. Connect Antenna: Securely attach the provided rubber rod antenna to the SMA interface on the module.
  2. Power Supply: Connect the VCC pin to a 3-5.5V power source and GND to ground. Ensure correct polarity.
  3. Data Communication: Use the UART_TX and UART_RX pins for serial communication. If using the USB to TTL Adapter Board, connect the module to the adapter board, then connect the adapter board to your computer via USB.
  4. Adapter Board Wiring: When using the adapter board, ensure the module is inserted with positive and negative pins correctly aligned. The adapter board typically provides 3.3V/GND, 5V/5V, RX/RX, TX/TX, and CNC/NC connections.
LR01 Backplane Pinout and Wiring Diagram with Adapter Board
Figure 7: LR01 Backplane Pinout and Wiring Diagram with Adapter Board

6. Operating Modes

The DX-LRO2 module supports several data transmission modes:

  • Transparent Transmission: Data is sent directly from one module to another without specific addressing, provided they are on the same channel.
  • Fixed-point Transmission: Modules communicate with specified addresses and channels. Data transmission format typically includes address, receiving channel, and data.
  • Broadcast Transmission: Modules communicate with designated channel modules. Data transmission format includes address channel and data, allowing multiple receivers on the same channel to receive the broadcast.
Support Working Mode: Transparent, Fixed-point, Broadcast Transmission
Figure 8: LoRa Module Support Working Modes

7. AT Commands

The DX-LRO2 module is configured and controlled using AT commands via its UART serial interface. Here are some common AT commands:

AT Command Command Description
ATTest (Response OK)
+++Enter/exit AT command mode
AT+BAUDSet/query baud rate
AT+MODESet/query operating mode
AT+SLEEPSet/query power consumption mode
AT+CHANNELSet/query working channels
AT+MACSet/query device address
AT+POWESet/query transmit power
AT+IQSetting the IQ signal flip-flop
AT+RESETSoftware Reboot
AT+DEFAULTRestore Factory Setting

For a complete list of AT commands and detailed usage instructions, please consult the product information packages available on the DX-SMART official website.

AT Command Set Table
Figure 9: AT Command Set Table

8. User Tips

  • Verify Package Contents: The developer package typically includes two modules, two USB cables, two antennas, and two USB to TTL adapter boards. Always check your package against the product description to ensure all expected components are present.
  • Antenna Connection: Always ensure the antenna is securely connected before powering on the module to prevent damage to the RF circuitry.
  • Power Supply: Use a stable power supply within the specified voltage range (3-5.5V) to ensure optimal performance and longevity of the module.

9. Troubleshooting

  • No Communication:
    • Check all wiring connections, especially power (VCC, GND) and UART (TX, RX).
    • Verify the baud rate settings on both the module (via AT commands) and your serial terminal.
    • Ensure the module is in AT command mode if you are trying to configure it.
  • Poor Range/Signal:
    • Ensure the antenna is correctly attached and undamaged.
    • Check for obstructions between transmitting and receiving modules.
    • Verify the transmit power settings using AT commands.
    • Ensure both modules are operating on the same frequency band and channel.
  • Module Not Responding:
    • Cycle power to the module.
    • Try a software reboot using the AT+RESET command.
    • If issues persist, consider restoring factory settings with AT+DEFAULT.

10. Maintenance

To ensure the longevity and optimal performance of your DX-LRO2 module:

  • Storage: Store the module in a dry, anti-static environment, away from extreme temperatures and humidity.
  • Handling: Handle the module with care to avoid physical damage to components or pins. Use anti-static precautions when handling.
  • Cleaning: Keep the module free from dust and debris. Use a soft, dry brush or compressed air for cleaning if necessary. Avoid liquid cleaners.
  • Environmental Conditions: Operate the module within its specified operating temperature range (-40°C to +85°C).

11. Warranty and Support

The DX-LRO2 module meets global certification standards including CE, FCC, RoHS, and ISO, ensuring quality and compliance.

Professional Technical Documentation and Certifications (CE, FCC, RoHS, ISO)
Figure 10: Professional Technical Documentation and Certifications

For professional technical documentation, including detailed datasheets, product specifications, module pinouts, dimensions, package diagrams, hardware design references, serial test tools, and comprehensive AT command sets, please visit the official DX-SMART website. The manufacturer, Shenzhen DX-SMART Technology Co., Ltd., offers one-stop IoT solutions and supports OEM/ODM services.

If you require further assistance or have specific inquiries, please contact DX-SMART directly through their official channels.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.