1. Introduction
This manual provides essential information for the safe and effective use of your U.S. Solid Liquid Nitrogen Sprayer. Please read these instructions carefully before operating the device. This sprayer is designed for controlled application of liquid nitrogen for various purposes, utilizing its cryo-freezing capabilities.
2. Safety Information
WARNING: Liquid nitrogen is extremely cold (-196°C / -320°F) and can cause severe frostbite or cryogenic burns upon contact with skin or eyes. Always handle with extreme caution.
- Always wear appropriate personal protective equipment (PPE), including cryogenic gloves, safety glasses or a face shield, and long-sleeved clothing, when handling liquid nitrogen or operating the sprayer.
- Use in a well-ventilated area to prevent oxygen displacement, which can lead to asphyxiation. Liquid nitrogen rapidly vaporizes into gaseous nitrogen, which is an inert gas.
- Never seal liquid nitrogen in an airtight container, as pressure buildup can cause an explosion.
- Avoid direct contact of liquid nitrogen with skin, eyes, or clothing. If contact occurs, immediately flush the affected area with lukewarm water and seek medical attention.
- Keep the sprayer upright to prevent spills.
- Do not ingest liquid nitrogen.
- Keep out of reach of children and untrained personnel.
3. Package Contents
Carefully unpack your liquid nitrogen sprayer and verify that all components are present and undamaged. Refer to the unboxing video for visual guidance.
Video: Unboxing and component overview of the U.S. Solid Liquid Nitrogen Sprayer.
- 1 x Container Body (500 ml / 16 oz)
- 1 x Liquid Nitrogen Cup Lid with Pipe and Adjustable Discharge Valve
- 1 x Handle
- 9 x Frozen Heads (8 without a hole, 1 with a hole)
- 1 x Instruction Manual
- Assorted spare parts (e.g., O-rings)


4. Specifications
| Attribute | Value |
|---|---|
| Model Number | USS-LNS00001 |
| Capacity | 500 ml (16 oz) |
| Material | Double layer stainless steel (anti-explosion, crack, rust) |
| Height | 22 cm (8.7") |
| Diameter | 7.9 cm (3.1") |
| Pipe Length | 11 cm (4.3") |
| Handle Length | 11.5 cm (4.5") |
| Cover Diameter | 5 cm (2.0") |
| Gross Weight | 2000 g (4.4 lbs) |
| Origin | Mainland China |
5. Setup
- Unpack Components: Remove all parts from the carrying case. Ensure the container body, lid with pipe, handle, and all 9 frozen heads are present.
- Attach Handle: Securely attach the clear handle to the side of the container body using the provided screws.
- Attach Pipe to Lid: The curved pipe is pre-attached to the lid. Ensure it is firmly in place.
- Select and Attach Frozen Head: Choose the appropriate frozen head for your application. The set includes 8 heads without a hole for direct contact freezing and 1 head with a hole for spray application. Screw the selected head onto the end of the curved pipe.
- Fill with Liquid Nitrogen:
- Ensure you are wearing all necessary PPE.
- The sprayer does NOT come with liquid nitrogen. You must purchase liquid nitrogen separately from a reputable supplier.
- Carefully pour liquid nitrogen into the container body. Do not overfill.
- Immediately place the lid assembly onto the container body.

6. Operating Instructions
Once the sprayer is filled with liquid nitrogen and the desired head is attached, you can begin operation.
- Adjust Flow: The sprayer features an adjustable discharge valve on the lid. Rotate the switch on the lid to control the flow rate of liquid nitrogen. Turning it clockwise will decrease flow, and counter-clockwise will increase it.
- Application:
- For spray application (using the head with a hole), aim the nozzle at the target area and press the handle to release the liquid nitrogen.
- For direct contact freezing (using heads without a hole), gently press the head against the target area.
- Observe Frosting: As liquid nitrogen is dispensed, the pipe and nozzle will become frosted. This is normal and indicates the extremely low temperature. Avoid touching frosted parts directly with bare skin.

7. Maintenance and Storage
- Cleaning: After each use, ensure the sprayer is empty of liquid nitrogen. Allow the device to return to ambient temperature. Clean the exterior with a soft, damp cloth. Do not immerse the entire unit in water.
- Lid Handling: When removing or attaching the lid, do not hold or twist the steel pipe. Always grasp the main lid body to avoid damaging the pipe connection.
- Liquid Nitrogen Storage: This sprayer is not designed for long-term storage of liquid nitrogen. Liquid nitrogen will evaporate over time (typically 12-20 hours, depending on ambient temperature). For long-term storage, use a dedicated liquid nitrogen dewar.
- Storage: Store the empty and clean sprayer in its original carrying case in a dry, cool place, away from direct sunlight and extreme temperatures.
8. Troubleshooting
- No Spray/Low Flow:
- Check if there is sufficient liquid nitrogen in the container.
- Ensure the adjustable discharge valve on the lid is open (rotated counter-clockwise).
- Verify that the chosen frozen head is not clogged. Clean if necessary.
- Excessive Frosting: Frosting on the pipe and nozzle is normal due to the low temperature of liquid nitrogen. Ensure you are wearing appropriate cryogenic gloves to prevent frostbite.
- Difficulty Rotating Lid: Ensure you are grasping the main lid body and not the steel pipe when rotating. If the lid is stuck, ensure the unit is at ambient temperature and try again.
9. Warranty and Support
For information regarding warranty, returns, and refunds, please refer to the seller's policies on the purchase platform. General service commitments include:
- Refund if package lost.
- Refund if items damaged.
- Refund if no delivery in 30 days.
- A coupon may be provided for late delivery.
For technical support or further inquiries, please contact the seller directly through the platform where the product was purchased.