LIZAO ZK-SMC02

Contents

ZK-SMC02 Stepper Motor Controller User Manual

Integrated Stepper Motor Controller and Driver

1. Introduction

The ZK-SMC02 is an integrated stepper motor controller and driver module designed for single-axis stepper motors. It offers multiple fixed operating modes, allowing users to quickly select the appropriate motion trajectory. This module can loop and set parameters such as distance, speed, delay, and number of cycles, with settings retained after power-off. It can operate independently or integrate with other systems, making it suitable for general industrial control applications. It is compatible with 2-phase, 4-wire, 6-wire, and 8-wire stepper motors.

ZK-SMC02 Stepper Motor Controller front view
Figure 1: ZK-SMC02 Stepper Motor Controller Front View. Shows the integrated controller and driver, ready for direct connection to a stepper motor.

2. Key Features

  • Integrated stepper motor controller and driver.
  • Physical buttons for direct control.
  • LCD display for real-time information and settings.
  • Multiple automatic and manual operating modes.
  • TTL serial communication support.
  • Adjustable delay, speed, angle, and distance.
  • Supports 2-phase, 4-wire, 6-wire, and 8-wire stepper motors.
  • Acceleration and deceleration control.
  • Input reverse protection.

3. Specifications

Table 1: ZK-SMC02 Technical Specifications
ParameterValue
ModelZK-SMC02
Adapted MotorStepper motor (42, 57 series)
Number of Control AxesSingle axis
Motor SignalCommon cathode
Power Supply RangeDC 5-30V (universal)
Driving Current0-4A (adjustable)
Acceleration/Deceleration ControlYes
Input Reverse ProtectionYes
Remote Communication ControlTTL serial port
Main FunctionsAutomatic, manual, settings, serial port control
Speed Display Range0.1-999 revolutions per minute
Forward Pulse Count1-9999 pulses
Reverse Pulse Count1-9999 pulses
Cycle Working Frequency1-9999 times
Forward Delay Time0-99.993 seconds
Reverse Delay Time0-99.993 seconds
Subdivision Selection Range1-99 subdivisions
Operating Temperature-5°C to +60°C (no condensation)
Dimensions (L x W x H)79 x 43 x 42 mm
Net Weight64g
Weight (including packaging)90g
ZK-SMC02 Dimensions
Figure 2: ZK-SMC02 Physical Dimensions.

4. Product Overview and Components

The ZK-SMC02 features a user-friendly interface with physical buttons and an LCD for easy operation and monitoring.

ZK-SMC02 Front Panel Controls
Figure 3: Front Panel Controls and Indicators.
  • CW Button (Corotation): Initiates forward rotation.
  • CCW Button (Inversion): Initiates reverse rotation.
  • RUN/STOP Button: Starts or pauses motor operation. Long press to exit running mode.
  • Encoder Setting Knob: Used for adjusting parameters and navigating menus. Short press to confirm, long press to save and exit.
  • Forward Rotation Indicator Light: Illuminates when the motor is rotating forward.
  • Reverse Indicator Light: Illuminates when the motor is rotating in reverse.
  • LCD Display: Shows current speed, pulse count, menu options, and other operational information.
ZK-SMC02 Rear View with Connections and DIP Switches
Figure 4: Rear View showing wiring terminals, current regulation potentiometer, and subdivision DIP switches.
  • Subdivision Settings (DIP Switches): Configures the motor's micro-stepping.
  • Current Regulation Potentiometer (0-4A): Adjusts the driving current for the stepper motor.
  • Optocoupler Isolation: Provides electrical isolation for control signals.
  • Wiring Terminals (A+, A-, B+, B-): Connect to the stepper motor windings.
  • Power Supply Terminals (Power supply+, Power supply-): Connect to a DC 5-30V power source.
  • Control Signal Terminals (Public line, Stop signal, Reverse signal, Forward signal, Reserved signal): For external control inputs.
  • Serial Communication Terminals (GND, EN, DIR, PUL, +3.3V, TX, RX): For TTL serial communication.

5. Setup and Wiring

5.1. Power Supply Connection

Connect a DC power supply (5-30V) to the "Power supply+" and "Power supply-" terminals. Ensure correct polarity.

5.2. Stepper Motor Connection

Connect your 2-phase, 4-wire, 6-wire, or 8-wire stepper motor to the A+, A-, B+, B- terminals. Refer to your motor's datasheet for correct winding connections. The ZK-SMC02 uses a common cathode motor signal.

ZK-SMC02 Product Wiring Diagram
Figure 5: Example Product Wiring Diagram. Shows connections for a button, external power supply, and the stepper motor to the ZK-SMC02.

5.3. Current Regulation

Adjust the current regulation potentiometer (0-4A) on the back of the module to match the rated current of your stepper motor. Incorrect current settings can lead to overheating or poor performance.

5.4. Subdivision Settings (Micro-stepping)

The ZK-SMC02 uses DIP switches (S1, S2, S3) to set the motor subdivision (micro-stepping). Adjust these switches according to the desired resolution. The number of pulses per revolution for your stepper motor will depend on this subdivision setting and the motor's step angle.

Table 2: Subdivision Settings (DIP Switches)
S3S2S1M_SET (Subdivision)
ONONON2
ONONOFF2/A
ONOFFON4
ONOFFOFF8
OFFONON16
OFFONOFF32

Note: "ON" typically means the switch is in the down position, and "OFF" means up, but this can vary by DIP switch manufacturer. Consult the physical switch for markings if unsure.

6. Operating Instructions

6.1. Interface Overview

The ZK-SMC02 has two main interfaces:

  • Run Interface: Displays real-time running information (e.g., speed, position).
  • Menu Settings Interface: Where all adjustable parameters are configured.
ZK-SMC02 Run and Menu Interfaces
Figure 6: Examples of the Run Interface (top) and Menu Settings Interface (bottom).

6.2. Basic Operation

  1. From Run Interface:
    • Rotate the encoder to adjust the speed.
    • Press the CW button for forward rotation.
    • Press the CCW button for reverse rotation.
    • Press the RUN/STOP button to stop the motor and exit the running state.
    • Long press the encoder to enter the Menu Settings interface.
  2. From Menu Settings Interface (Parameter Selection):
    • Rotate the encoder to cycle through parameter codes (F-01 to F-13).
    • Long press the encoder to save the current parameter selection and exit back to the running interface.
  3. From Menu Settings Interface (Parameter Adjustment):
    • While on a specific parameter code (e.g., F-01), short press the encoder to enter its setting state. The parameter value will flash.
    • Short press the encoder again to shift between digits (if applicable) or to confirm selection.
    • Rotate the encoder to adjust the flashing parameter value.
    • Short press the RUN/STOP button to exit the parameter setting state and return to the main menu number adjustment interface.

6.3. Menu Setting Functions (F-XX Parameters)

Table 3: ZK-SMC02 Menu Parameters
NumberFunctionAdjustable RangeDefault Value
F-01Process mode selection1-81
F-02Specific introduction below this tableN/AN/A
F-03Number of forward pulse units number1-99991600
F-04Forward speed (revolutions per minute)0.1-99930
F-05Reverse pulse count unit number1-99991600
F-06Reverse speed unit revolutions per minute0.1-99930
F-07Forward delay time0-99.990.0
F-08Reverse delay time0-99.990.0
F-09Cycles0-99991
F-10Pulse count for one revolution (1-9999)1-99991600
F-11Motor acceleration/deceleration slope1-51
F-12Emergency stop level1-10020
F-13Mail address (for serial communication)1-2551

6.4. Action Process Mode Selection (F-01)

The F-01 parameter allows selection of different operating modes. Choose the mode that best suits your application:

  • P01->1: Knob Control: The motor's operation (speed, direction) is directly controlled by the encoder knob.
  • P01->2: Button-Controlled Continuous Rotation: After pressing a direction button (CW/CCW), the motor rotates continuously until the button is released.
  • P01->3: Button-Controlled Single Rotation: Pressing CW initiates forward rotation; pressing CCW initiates reverse rotation. The motor rotates for a set number of pulses (F-03/F-05) and then stops.
  • P01->4: Button-Controlled Rotation with Distance Stop: Pressing CW initiates forward rotation; pressing CCW initiates reverse rotation. The motor rotates until it reaches a pre-set distance (defined by F-03/F-05) and then stops.
  • P01->5: Button-Controlled Rotation with Distance Stop and Cycle: Similar to P01->4, but after stopping at the set distance, the process can be cycled.
  • P01->6: Button-Controlled Rotation with Distance Stop, Cycle, and Delay: Similar to P01->5, but includes a delay (F-07/F-08) between cycles or direction changes.
  • P01->7: Advanced Button-Controlled Rotation: Provides more complex control options, potentially involving external signals or specific sequences.
  • P01->8: Custom Programmed Rotation: Allows for highly customized motion profiles, likely through serial communication or advanced internal programming.

7. User Tips

  • Always ensure the power supply voltage is within the 5-30V DC range to prevent damage.
  • Carefully adjust the current regulation potentiometer to match your stepper motor's specifications to avoid overheating or insufficient torque.
  • When setting subdivision, remember that it directly affects the motor's resolution and the number of pulses required for a full revolution.
  • For precise control, experiment with the acceleration/deceleration slope (F-11) to achieve smooth starts and stops.
  • If using serial communication, ensure the correct mail address (F-13) is configured and your communication protocol matches.

8. Troubleshooting

  • Motor not moving or erratic movement:
    • Check power supply voltage and current.
    • Verify motor wiring (A+, A-, B+, B-). Incorrect wiring is a common issue.
    • Ensure the current regulation potentiometer is set appropriately for your motor.
    • Check subdivision settings (DIP switches) and ensure they match your expectations.
    • Confirm the selected operating mode (F-01) is appropriate for your intended action.
  • LCD display is blank or unreadable:
    • Check power supply connection.
    • Ensure the module is not exposed to extreme temperatures outside its operating range.
  • Motor overheating:
    • Reduce the driving current using the potentiometer.
    • Ensure the motor is not overloaded.
  • Inaccurate positioning:
    • Verify the pulse count settings (F-03, F-05, F-10) and ensure they correspond to your motor's step angle and the chosen subdivision.
    • Check for mechanical issues in the motor or load.

9. Maintenance

  • Keep the module clean and free from dust and debris.
  • Avoid exposing the module to moisture or corrosive environments.
  • Ensure adequate ventilation, especially if operating at higher currents, to prevent overheating.
  • Periodically check wiring connections for looseness or corrosion.
  • Do not attempt to disassemble the module beyond what is necessary for wiring or adjustment.

10. Warranty and Support

For technical support, troubleshooting assistance, or warranty inquiries, please contact your retailer or the manufacturer directly. Please have your product model number (ZK-SMC02) and purchase information ready when seeking support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.