1. Introduction
The Hti HT-1202 Digital PH Meter is a precise instrument designed for measuring pH and mV values in various liquid environments. It is ideal for applications such as mariculture, freshwater farming, and general water quality assessment. This manual provides comprehensive instructions for the safe and effective use of your device.

2. Product Overview and Components
Familiarize yourself with the main components of your HT-1202 PH Meter:

- Host Interface: Connection point for the pH electrode.
- Display Screen: LCD display showing measurement values and temperature.
- PH Combined Electrode: The sensor probe for pH and mV measurements.
- Keypad: Buttons for operation and settings.
- Battery Box: Located at the back of the device for battery installation.
The package typically includes:
- Hti HT-1202 PH Meter Host
- PH Combined Electrode
- Standard buffer reagents (one package each for PH4.00, PH6.86, and PH9.18)
- Potassium chloride powder package
- User Manual
- 3 AA batteries (not always included, check packaging)

3. Setup Instructions
3.1 Battery Installation
- Locate the battery compartment on the back of the device.
- Open the battery cover.
- Insert 3 x 1.5V AA batteries, ensuring correct polarity.
- Close the battery cover securely.

3.2 Electrode Connection
- Connect the PH combined electrode to the host interface port on the top of the meter.
- Ensure the connection is firm and secure.
4. Operating Instructions
4.1 Power On/Off
- Press the power button (Power key) to turn the device on.
- The device will automatically shut down after 4 minutes of inactivity to conserve battery.
4.2 Display Interpretation

- Measured Value: Displays the current pH or mV reading.
- Temperature Value: Shows the temperature of the measured solution in Celsius.
- PH/mV Indicator: Indicates whether the displayed value is pH or mV.
- Battery Capacity: Shows the remaining battery life.
- Calibration Indicators: '1' for acid solution, '2' for alkali solution.
4.3 Taking Measurements
- Ensure the electrode is clean and properly connected.
- Immerse the PH combined electrode into the solution to be measured.
- Allow a few moments for the reading to stabilize on the display.
- To switch between pH and mV display, use the appropriate button on the keypad (refer to Figure 4).
4.4 Calibration
Regular calibration is crucial for accurate measurements. Use the provided buffer reagents for calibration.
- Press the 'Menu' button to enter calibration mode.
- Follow the on-screen prompts to calibrate with PH4.00, PH6.86, and PH9.18 buffer solutions.
- Press 'Enter' to confirm selections and 'Esc' to exit.
4.5 Backlight
The device features a backlight for improved readability in low-light conditions. Press the 'Enter/backlight key' (refer to Figure 4) to toggle the backlight on or off.
5. Maintenance
5.1 Electrode Care
- Always rinse the electrode with distilled water before and after each use.
- Store the electrode in a potassium chloride solution (prepared from the provided powder) or a suitable electrode storage solution when not in use to prevent drying out.
- Do not allow the electrode to dry out, as this can affect its performance and lifespan.
5.2 Cleaning the Device
- Wipe the meter's body with a soft, damp cloth.
- Do not use abrasive cleaners or solvents.
- Ensure no liquid enters the device's internal components.
5.3 Storage
- Store the device in a cool, dry place, away from direct sunlight and extreme temperatures.
- If storing for an extended period, remove the batteries to prevent leakage.
6. Troubleshooting
If you encounter issues with your HT-1202 PH Meter, consider the following:
- Inaccurate Readings: Ensure the electrode is clean and properly calibrated. Check if the buffer solutions are fresh.
- No Display: Check battery installation and battery level. Replace batteries if necessary.
- Slow Response: The electrode might be dirty or dry. Clean and re-hydrate the electrode.
- Error Messages: Refer to the specific error codes in the full user manual (if provided) or contact customer support.
7. Specifications
| Feature | Specification |
|---|---|
| Model Number | HT-1202 |
| Brand Name | Hti |
| Display Type | DIGITAL (3 and a half digit display) |
| PH Range | 0PH~14PH |
| mV Range | -415mV~415mV |
| Resolving Power | 0.01PH, 1mV |
| PH Measurement Error | ±0.05PH |
| Measurement Error of mV Value | ±0.1%FS |
| Temperature of Measured Solution | 5~60℃ |
| Temperature Compensation Range | 0~60℃ |
| Automatic Shutdown Time | 4 minutes |
| Host Weight | 145g |
| Host Size | 165mm×75mm×32mm |
| With Backlight Or Not | Yes |
| Is Smart Device | No |
| Battery Included | No |
| Hign-concerned Chemical | None |
| Origin | Mainland China |
| Certification | CE, RoHS |
| Attachments | Standard buffer reagents (PH4.00, PH6.86, PH9.18), instruction manual, potassium chloride powder package, pH non-rechargeable composite electrode |
8. Warranty and Support
The Hti HT-1202 PH Meter is designed for durability and accuracy. For warranty information, technical support, or service inquiries, please refer to the contact details provided with your purchase or visit the official Hti Tools Store website. Keep your purchase receipt as proof of purchase for warranty claims.