1. Introduction
The JIKONG JK-BD6A20S12P is an intelligent active balanced Battery Management System (BMS) designed for various lithium battery types, including Li-ion, LiFePo4, and LTO. This smart BMS supports battery configurations from 8S to 24S and offers robust protection features, active balancing, and comprehensive monitoring capabilities via mobile app and PC software. It is suitable for a wide range of applications from e-bikes to energy storage systems.

2. Package Contents
Please verify that all items are present and in good condition upon unpacking:

- 1 x JIKONG BMS Unit
- 1 x Switch (50cm long)
- 1 x NTC Temperature Sensor (40cm long)
- 1 x Sampling Line B (70cm long)
- 1 x Sampling Line A (70cm long)
3. Specifications
The JIKONG JK-BD6A20S12P BMS offers advanced features and robust performance. Below are the key technical specifications:

| Feature | Specification |
|---|---|
| Number of Battery Strings (Li-ion, LiFePo4, LTO) | 8S-20S |
| Balance Method | Active Balance (Full State On) |
| Balance Current | 0.6A |
| Conductive Resistance in Main Circuit | 0.5mΩ |
| Continuous Discharge Current | 200A |
| Continuous Charge Current | 200A |
| Maximum Discharge Current (MAX 3min) | 350A |
| Over Charge Protection Current (μA) | 10-100A |
| Other Interfaces (Customized) | CANBUS, RS485, HEAT |
| Size (mm) | 162*102*20mm |
| Wiring Output | Common Port |
| Single Cell Voltage Range | 1-5V |
| Voltage Detection Accuracy | ±5mV |
| Overcharge Protection Voltage | 1.2-4.35V Adjustable |
| Over Charge Release Voltage | 1.2-4.35V Adjustable |
| Over Current Detect Delay | 2-120S Adjustable |
| Over Discharge Protection Voltage | 1.2-4.35V Adjustable |
| Over Discharge Release Voltage | 1.2-4.35V Adjustable |
| Quantity of Temperature Detection | 3 Pcs |
| Temp Protection | Yes |
| Short Circuit Protection | Yes |
| Coulomb Counter | Yes |
| Bluetooth Function | Support for Android/iOS phone |
Physical Dimensions:

- Length: 162mm
- Width: 102mm (main body), 95mm (with ports)
- Thickness: 16.6mm
4. Setup and Installation
Careful installation is crucial for the safe and effective operation of your BMS. Always ensure the battery pack is disconnected from any power sources before beginning installation.
4.1 Wiring Instructions
- Connect all balance cables: Ensure each balance wire from the battery cells is connected to the corresponding pin on the BMS balance port. Start from the lowest cell voltage (B1) and proceed upwards.
- Insert the cable into the BMS: Once all balance wires are correctly connected to the harness, carefully plug the harness into the designated port on the BMS.
- Connect the B-line and P-line to the battery: Connect the main negative terminal (B-) of the battery pack to the B- terminal on the BMS. Connect the main positive terminal (P+) of the battery pack to the P+ terminal on the BMS. The P- terminal on the BMS is for the load/charger negative connection.

4.2 Interface Overview
The BMS features a rich set of interfaces for communication and external connections:

- RS485/CAN Port: For communication with inverters and other external devices.
- NTC Port: For connecting the NTC temperature sensor.
- GPS Port: For GPS module connection (if applicable).
- Sampling Port B & A: For connecting the cell voltage sampling lines.
- Display/Switch Port: For connecting external display units or the included switch.
- Hot Port: For heating element control (if applicable).
5. Operation
The JIKONG BMS offers intelligent interaction and easy operation through its dedicated mobile application and PC software.
5.1 Mobile App & PC Software
The 'JIKONG SMART BMS' mobile application (available for iOS, Android, and HarmonyOS) and PC software allow for real-time monitoring and parameter adjustment.


- Real-time Data: Monitor battery voltage, current, temperature, State of Charge (SOC), and cycle count.
- Parameter Adjustment: Freely adjust multiple protection values such as overcharge voltage, over-discharge voltage, overcurrent limits, temperature thresholds, and balancing parameters. Refer to the internal parameters section of the software/app before making changes.
- Multi-language Support: The app supports multiple languages, automatically switching with your mobile phone system.
5.2 Inverter Communication Protocols
The BMS is compatible with mainstream inverter communication protocols and can be configured via the mobile app or host computer software.


6. Maintenance
The JIKONG BMS is designed for durability and reliability with minimal maintenance requirements.
6.1 Physical Protection
The BMS features a fully enclosed aluminum alloy shell, providing excellent dustproof, waterproof, anti-voltage, and anti-vibration properties. Internal high-strength insulating material filling further protects components from external environmental factors and vibrations.

6.2 Heat Dissipation
The aluminum alloy casing and one-piece molding technology ensure superior heat dissipation, with a thermal conductivity significantly higher than iron or plastic, contributing to the longevity and stable performance of the BMS.

6.3 General Care
- Keep the BMS clean and free from excessive dust buildup.
- Ensure proper ventilation around the unit, especially in high-current applications.
- Regularly check cable connections for tightness and signs of wear.
7. Troubleshooting
This section provides guidance on common issues you might encounter with your JIKONG BMS.
| Problem | Possible Cause | Solution |
|---|---|---|
| BMS not powering on/no display | Incorrect wiring, loose connections, battery voltage too low. | Check all wiring according to the diagram. Ensure battery voltage is within the operating range. Verify balance cable connections. |
| Overcharge/Over-discharge protection triggered | Battery cells exceeding/falling below voltage limits. | Check individual cell voltages via the app. Adjust protection parameters if necessary (within safe limits for your battery chemistry). Ensure charger/load is appropriate. |
| Overcurrent/Short circuit protection triggered | Load drawing too much current, short circuit in wiring or load. | Reduce load. Inspect wiring and load for short circuits. Adjust overcurrent protection settings if appropriate for your application. |
| Temperature protection triggered | Battery or BMS temperature too high/low. | Ensure adequate ventilation. Check NTC sensor placement and functionality. Operate within recommended temperature ranges. |
| Balancing not effective | Significant cell voltage difference, balance current too low for imbalance. | Allow sufficient time for balancing. For large imbalances, consider pre-balancing cells. Ensure balance function is enabled in the app/software. |
| Bluetooth connection issues | BMS not powered, Bluetooth disabled on phone, interference. | Ensure BMS is powered. Enable Bluetooth on your device. Move closer to the BMS. Restart app/BMS. |
8. User Tips
- Initial Setup: Always connect the balance wires to the BMS *before* connecting the main battery terminals (B- and P-). This prevents potential damage from voltage spikes.
- Parameter Customization: While the BMS allows for adjustable protection values, always ensure these settings are appropriate and safe for your specific battery chemistry and cell specifications. Incorrect settings can lead to battery damage or safety hazards.
- Monitoring: Regularly check the battery status via the mobile app or PC software, especially during initial use and after any changes to the system. Pay attention to cell voltage differences and temperature.
- Firmware Updates: Check the official JIKONG website or app for any available firmware updates to ensure optimal performance and access to new features.
- Application Scenarios: The JIKONG BMS is versatile and suitable for various applications including e-bikes, electric tricycles, forklifts, industrial drones, RV energy storage, and power tools. Ensure the chosen BMS model (e.g., current rating) matches your application's requirements.

9. Warranty and Support
For warranty information, technical support, or service inquiries, please contact JIKONG Official Store directly through the platform where you purchased the product. Ensure you have your purchase details and product model number (JK-BD6A20S12P) ready for faster assistance.