Introduction
The GVM H3 is a versatile 3-in-1 smart soldering station designed for precision electronics repair, particularly mobile phone motherboards and chip-level work. It features rapid 2-second heating, intelligent temperature control, automatic tool identification, and a convenient 3-channel temperature storage system. This manual provides essential information for the safe and efficient operation of your GVM H3 soldering station.
Figure 1: GVM H3 Soldering Station with included handles, tips, and solder wire.
Package Contents
Before setup, please verify that all items listed below are present in your package:
Figure 2: Illustrated package contents.
- Soldering station host (1 unit)
- T245 handle (1 unit)
- T210 handle (1 unit)
- T115 handle (1 unit)
- T245 heating core (1 unit)
- T210 heating core (1 unit)
- T115 heating core (1 unit)
- Power cable (1 unit)
- Ground wire (1 unit)
- Cable bracket (1 unit)
- Cable bracket thumb screws (2 units)
- Anti-scalding silicone pad (1 unit)
- Product manual (1 unit)
- Product certification (1 unit)
- Cleaning sponge (1 unit)
- Copper wire ball (1 unit)
- Adjustable bracket screw (1 unit)
Setup
- Unpacking: Carefully remove all components from the packaging.
- Placement: Place the soldering station on a stable, heat-resistant, and non-flammable surface. Ensure adequate ventilation.
- Connect Power:
Figure 3: Rear panel interfaces.
- Connect the power cable to the Power cord interface on the rear panel of the station.
- Plug the other end of the power cable into a suitable AC power outlet (ensure voltage matches station requirements: AC220V/110V).
- Connect the ground wire to the Ground interface for safety.
- Install Handles: Connect the desired soldering iron handle (T245, T210, or T115) to the Soldering iron handle interface on the rear panel. The station automatically identifies the connected tool.
- Install Cable Bracket: Attach the cable bracket to the designated slot on the station using the thumb screws to help organize the handle cable.
- Prepare Cleaning Tools: Place the copper wire ball and sponge in their respective compartments for easy access during operation.
Operating Instructions
- Power On: Flip the main power switch on the rear panel to the 'ON' position. The LCD display will illuminate.
- Temperature Adjustment:
- Use the 'Temperature+' and 'Temperature-' buttons (up/down arrows) on the front panel to adjust the desired temperature.
- The LCD provides visual feedback on the current and set temperatures.
- Channel Temperature Storage:
Figure 4: 3-channel temperature storage.
- The station features three memory channels (CH1, CH2, CH3) for quick temperature recall.
- To set a channel: Adjust to the desired temperature, then long-press the corresponding channel button (CH1, CH2, or CH3) until the setting is saved.
- To recall a channel: Short-press the corresponding channel button (CH1, CH2, or CH3) to instantly switch to the stored temperature.
- Automatic Tool Identification:
Figure 5: Automatic identification of soldering handles.
The GVM H3 automatically detects which handle (T245 for high power, T210 for precision components, T115 for special precision components) is connected, optimizing performance for the specific tool.
- Intelligent Induction Sleep:
Figure 6: Intelligent induction sleep mode.
When the soldering iron handle is placed in its holder, the station automatically enters sleep mode to extend the life of the soldering iron tip and save energy.
- LCD Menu Navigation:
Figure 7: LCD menu for settings.
Access the menu using the 'Function menu key' (list icon) to adjust settings such as Sleep delay, Beep sound, Temperature unit (°C/°F), and Language (Chinese/English).
- USB Connection Port:
Figure 8: USB connection for PC assistant and firmware updates.
Connect the station to a computer via the USB port to use the PC assistant software for real-time temperature display, settings optimization, and firmware upgrades.
Maintenance
- Soldering Tip Cleaning:
Figure 9: Built-in tip cleaning tools.
Regularly clean the soldering tip using the built-in copper wire ball or damp sponge to remove solder residue and oxidation. This ensures efficient heat transfer and extends tip life.
- Heating Core Replacement:
Figure 10: Heating core storage and puller tool.
The heating element can be removed with one hand using the integrated heating core puller. Replace heating cores when performance degrades. Ensure the station is powered off and cooled before attempting replacement.
- General Cleaning: Keep the station clean and free from dust and debris. Use a soft, dry cloth for cleaning the exterior. Do not use abrasive cleaners or solvents.
- Storage: When not in use, store the soldering station in a dry, dust-free environment.
Troubleshooting
- No Power:
- Check if the power cable is securely connected to both the station and the power outlet.
- Ensure the main power switch is in the 'ON' position.
- Verify the power insurance (fuse) on the rear panel. Replace if blown.
- Soldering Iron Not Heating:
- Ensure the handle is properly connected to the station.
- Check if the heating core is correctly installed and not damaged.
- Verify the set temperature on the LCD display.
- Inaccurate Temperature Reading:
- Ensure the soldering tip is clean and properly seated.
- Consider replacing the heating core if accuracy issues persist.
- Station Not Responding:
- Power off the station, wait a few seconds, and power it back on.
- If issues persist, contact customer support.
Specifications
Figure 11: Detailed product specifications.
| Parameter | Value |
|---|---|
| Brand | GVM |
| Product Name | 3-in-1 smart soldering station |
| Model | GVM H3 |
| Net Weight | ≈ 1650g |
| Gross Weight | ≈ 2210g |
| Host Size | 150*135*104mm |
| T245 Handle Wire Total Length | ≈ 128mm |
| T210 Handle Wire Total Length | ≈ 126mm |
| T115 Handle Wire Total Length | ≈ 126mm |
| T245 Heating Core | 100*4.8mm |
| T210 Heating Core | 30*3.5mm |
| T115 Heating Core | 44.5*2.8mm |
| Package Size | 190*170*165mm |
| Rated Working Voltage | AC220V/110V (customizable) |
| Rated Power | 80W |
| Temperature Range | 100-480°C / 212-900°F |
| Temperature Range Accuracy | ±5°C/40°F |
| Temperature Stability | ±1°C/30°F |
| Supported Handle Types | 115/210/245 |
| Temperature Adjustment Step | ±5°C/10°F |
| Delayed Sleep | 0-180S, the delayed sleep function is canceled by default |
| Display Resolution | 240*320PX (LCD color screen) |
| System Language | Chinese-English bilingual switching |
| Working Conditions | 0~40 °C Humidity <80% |
| Storage Conditions | Temperature -20~80°C Humidity <80% |
User Tips
- Tip Compatibility: The GVM H3 is designed to work optimally with GVM T245, T210, and T115 handles and their corresponding heating cores. While some users inquire about compatibility with other brands like JBC, it is recommended to use original GVM components for guaranteed performance and safety.
- Pre-tinning Tips: Always pre-tin new soldering tips with solder before first use to prevent oxidation and ensure proper wetting.
- Temperature for Lead-Free Solder: When working with lead-free solder, you may need to set a slightly higher temperature compared to leaded solder due to its higher melting point.
- Firmware Updates: Periodically check the manufacturer's website for firmware updates to ensure your station has the latest features and performance improvements.
Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the contact information provided with your purchase or visit the official GVM website. Keep your proof of purchase for warranty claims.