1. Introduction
The Renolink V2.10 software is an advanced diagnostic and programming tool designed for Renault vehicles. It allows users to perform various functions including ECU programming, airbag reset, ECM (Engine Control Module), UCH (Unit Control Habitacle) management, and key coding. This manual provides detailed instructions for installing, operating, and maintaining the software to ensure optimal performance.
Video: Overview of Renolink V2.10 software functionality.
2. Setup and Installation
2.1. System Requirements
- Operating System: Windows 10 or Windows 11.
- Hardware Compatibility: Compatible with v1.99 / V1.87 versions of hardware and OBDLink SX.
- Incompatibility: VLinker FS is NOT supported.
2.2. Software Activation Process
Renolink V2.10 software requires activation. Only one computer can be activated per purchase. For multiple computers, a new order is required for each activation.
- Launch the Renolink Application: Double-click the Renolink shortcut on your desktop.
- Acknowledge Warning: If a warning about "Latency Timer" appears, click "OK".
- Open License Generator: Navigate to the "File" menu within the Renolink application and select "Open renolink.txt" or locate the "Renolink 2.10 - License Generator" application.
- Provide Cable Information: The license generator will display fields for "Serial number 1", "Serial number 2", "Serial number 3", "Device name", "Firmware", "Device vendor", and "Device id". This information is typically read from your diagnostic cable.
- Generate Hardware ID: The software will generate a "Hardware ID" from your PC.
- Receive Registration Key: You will need to send your Hardware ID to the seller to receive a unique "Registration key".
- Enter Registration Key: Input the provided Registration key into the corresponding field in the Keys Generator.
- Save License: Click "Save license" to complete the activation.
Figure 1: Renolink License Generator interface.
Figure 2: Cable information fields in the License Generator.
Figure 3: Keys Generator for hardware ID and registration key.
Figure 4: License Generator version information.
3. Operating Instructions
3.1. General Navigation
The Renolink interface features a menu bar at the top with options like File, Communications, Misc, Scan, Configuration, Extra, and Language. The left panel displays ECU and Screens options, while the main area shows diagnostic data and controls.
Figure 5: Main Renolink V2.10 software interface.
3.2. Scanning ECU
- Click on the "Scan" menu option in the top bar.
- In the "Scan Protocol Option" section, select "All" or a specific protocol if known.
- From the "Scan Ecu Option" dropdown, select "ECM" (Engine Control Module) or the relevant ECU type you wish to scan.
- Click the "Scan" button to initiate the scanning process. The progress will be displayed.
- Once scanning is complete, the detected ECU information will be listed. Click "Close" to exit the scan window.
Figure 6: ECU Scan window.
3.3. Accessing Parameters and Services
After connecting to an ECU, you can access various parameters and services from the left-hand "Screens" panel. Common screens include:
- Ecrans Services: General services.
- ReadMemoryByAdress: Read memory by address.
- Validation Routines Tests: Perform validation routine tests.
- Validation Services: Access validation services.
- Ecrans Trames: Frame screens.
- Banc_Moteur: Engine bench.
- Identification: View ECU identification data.
- Trame 01 Parametres generaux: General parameters (e.g., battery voltage, air temperature, pressure).
- Trame 02 Etat et Parametres secondaires: Secondary states and parameters.
- Trame 03 Papillon-Pedale: Throttle-pedal parameters.
- Trame 04 Adaptatif de richesse: Richness adaptation parameters.
- Trame 05 Rulent et VVT: Idle and VVT parameters.
- Trame 06 Structure Couple: Torque structure.
- Trame 07 OBD: OBD parameters.
- Trame 08 Jane_2: Specific Jane_2 parameters.
- Trame 09 Detronpage: Detonation parameters.
- Trame 10 Parametres Etudes: Study parameters.
- Trame 11 Throttle Area Curve: Throttle area curve data.
- Trame 31 CLIM: Climate control parameters.
- Trame 32 VSC: Vehicle Stability Control parameters.
- Trame 33 RVLV: Cruise control parameters.
Figure 7: Example of parameter display in Renolink.
3.4. Specific Functions
Renolink V2.10 offers specialized functions for various vehicle systems:
- Airbag Reset: Use the "Airbag Cleaner" function to reset airbag modules. Supported models include Clio3, Modus, Logan2, Sandero2, Dokker, Lodgy, Clio4, Captur, Duster ph2, Temmic, MRSZ_X95_L38_L43_L47, Scenic3, Fluence, Laguna3, Megane2, RC7, Kadjar, Talisman, Espace5, Master3, Trafic3, SDM, RSA_C1A.
- UCH Key Coding: Access the "Uch Cleaner" or "Keys" tab for UCH-related functions and key programming. Supported models include BMT Sagem, UCH_transv, UCH X65, UCH MUX X83, UCH Laguna2, UCH Megane2, UCH Clio3, UCH Koleos, UCH Kangoo2, UCH T4, HFM Clio 4, Arkana. The "Uch Eeprom" function is also available for specific models like CLIO II Ph2, KANGOO, TRAFIC, MASTER, VIVARO, MOVANO (-'07), LAGUNA II, ESPACE IV, VELSATIS, UCH T4 (1024KB), UCH T4_VS, HFM Clio 4.
- ECM Programming: Use the "Ecm Flash" function for ECM operations. Supported ECM types include Sirius 32, Ems 3132, Sirius 32N, Sirius 31H.
- ABS Programming: The "Abs" function supports various ABS systems for models like Laguna3, Megane3, Fluence, Latitude, Bosch (16K) for Twingo2, Logan2, Duster ph2, Clio4, Bosch (4K) for Twingo3, Logan2, Duster ph2, Clio4, Bosch (8K) for Twingo3, Logan2, Duster ph2, Clio4, and ABS ATE for Dokker, Lodgy.
- EPS Programming: The "Eps Cleaner" function is available for models such as Clio3, Modus, Megane3, Scenic3, Clio4, Twingo3, Duster ph3, Logan3, Sandero3, Megane4, Scenic4, Talisman, Kadjar, Clio5, Captur2.
- Steering Assist Virginiser: For Renault Megane 4, Scenic 4, Kadjar, and Talisman, the software can virginise the steering assist. Coding will occur automatically upon the first ignition.
- PIN Code Reading: The software supports reading PIN codes for HFM Renault Clio 4 and Renault Captur 2016+. A valid card is required to teach HFM, as the procedure virginises it.
- Card Programming: Card programming is supported for Clio4 (2012-2015).
Figure 8: Airbag Cleaner interface.
Figure 9: UCH Cleaner interface.
Figure 10: ECM Flash interface.
Figure 11: ABS Programming interface.
Figure 12: EPS Cleaner interface.
3.5. Language Selection
The software supports multiple languages. To change the language:
- Click on the "Language" menu in the top bar.
- Select your desired language from the dropdown list (English, French, Polish).
Figure 13: Language selection menu.
4. Maintenance
Keep your Renolink software up-to-date to ensure compatibility with the latest vehicle models and access to new features. Database updates, such as those from December 2019 and July 2019, are periodically released to enhance functionality.
5. Troubleshooting
- Software Not Launching: Ensure your operating system is Windows 10 or Windows 11. Check for any antivirus software blocking the application.
- Connection Issues: Verify that your diagnostic hardware (v1.99 / V1.87 versions or OBDLink SX) is correctly connected to the vehicle and your computer. Ensure the hardware is compatible (VLinker FS is not supported).
- Activation Problems: Double-check that the Hardware ID sent to the seller is correct and that the Registration Key received is entered accurately. Remember, activation is for one computer only.
- Performance Warning: If prompted to set "Latency Timer to 1 ms on serial port" for best performance, follow the recommendation.
6. Specifications
| Feature | Specification |
|---|---|
| Brand Name | OBDOK |
| Model Name | renolink v2.10 |
| Software Version | V2.10 |
| Hardware Version | New |
| Supported Operating Systems | Windows 10, Windows 11 |
| Supported Hardware | v1.99 / V1.87 versions of hardware, OBDLink SX |
| Unsupported Hardware | VLinker FS |
| Supported Languages | English, French, Polish |
| Item Weight | 0.05kg |
| External Testing Certification | CE |
| Wireless Function | No |
| Wireless Support | No |
| Batteries Included | No |
| Power | Not specified (W) |
| Voltage | Not specified (V) |
7. User Tips
- The software supports Polish, English, and French languages, which can be selected from the 'Language' menu.
- This product is for software only; a diagnostic cable is not included.
- Renolink V2.10 is confirmed to support Renault Clio 4 (2016 models for PIN code reading, 2012-2015 for card programming) and Megane 4 (for steering assist virginiser).
- For optimal performance, ensure your PC's Latency Timer is set to 1 ms on the serial port if prompted by the software.
8. Warranty and Support
For detailed item guides and documents, including the user manual in PDF format, please refer to the official product page or contact the seller directly. The PDF manual can be found at: User manual (PDF).