1. Introduction
The DYMO LM160 LabelManager is a portable, handheld label maker designed for creating custom labels quickly and efficiently. It supports DYMO D1 label tapes in widths of 6mm, 9mm, and 12mm, making it versatile for various labeling needs in homes, offices, and other environments. This device features a QWERTY keyboard for easy text entry and a monochrome printer output.
2. Package Contents
Please check the package for the following items:
- 1 x DYMO LM160 LabelManager Label Maker
- 1 x DYMO D1 Starter Label Tape (typically Black on White, 12mm)
- 1 x Instruction Manual (this document)
3. Setup
3.1 Battery Installation
- Locate the battery compartment cover on the back of the label maker.
- Press down on the latch and slide the cover off.
- Insert 6 AAA alkaline batteries, ensuring correct polarity (+/-) as indicated inside the compartment.
- Replace the battery compartment cover, sliding it until it clicks into place.
3.2 Label Tape Installation
- Open the label tape compartment cover, usually located on the top-front of the device.
- Insert the DYMO D1 label cassette into the compartment. Ensure the tape and ribbon are properly aligned with the guides.
- Press the cassette firmly until it locks into place.
- Close the label tape compartment cover.
4. Operating Instructions
4.1 Power On/Off
- To turn on the label maker, press the Power button (usually indicated by a circle with a vertical line).
- To turn off the label maker, press and hold the Power button until the screen turns off. The device may also power off automatically after a period of inactivity.
4.2 Text Entry and Editing
- Use the QWERTY keyboard to type your desired text.
- Use the Arrow keys to navigate the cursor on the display.
- Press the Backspace key (left arrow with 'X' or similar icon) to delete characters.
- Press the OK button to confirm selections or move to the next step in certain menus.
4.3 Formatting Options
The LM160 offers various formatting options to customize your labels:
- Font Size (AA): Adjust the size of your text.
- Bold (B): Apply bold formatting.
- Italics (I): Apply italic formatting.
- Underline (U): Apply underline formatting.
- Menu Button: Access additional formatting options, symbols, and settings.
4.4 Printing Labels
- After entering and formatting your text, press the Print button (usually indicated by a printer icon).
- The label maker will feed and print the label.
- Once printed, use the integrated cutter on the side of the device to manually cut the label.
5. Maintenance
5.1 Cleaning the Print Head
To ensure optimal print quality, clean the print head periodically:
- Turn off the label maker and remove the label cassette.
- Use a soft, lint-free cloth or a cotton swab lightly dampened with rubbing alcohol to gently wipe the print head.
- Allow the print head to dry completely before reinserting the label cassette and turning on the device.
5.2 General Cleaning
- Wipe the exterior of the label maker with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Keep the label maker free from dust and debris.
5.3 Label Tape Usage
Always use authentic DYMO D1 label tapes for the best performance and to prevent damage to your label maker.
6. Troubleshooting
If you encounter issues with your DYMO LM160, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not power on | Dead or incorrectly inserted batteries | Replace batteries with fresh ones, ensuring correct polarity. |
| Poor print quality (faint, streaky) | Dirty print head; old or faulty label tape | Clean the print head (see Section 5.1). Replace the label tape cassette. |
| Label tape jam | Incorrectly inserted tape; foreign object | Turn off the device, open the tape compartment, and carefully remove any jammed tape. Reinsert the tape correctly. |
| "Tape Error" message | Tape not detected or improperly installed | Ensure the label tape cassette is fully seated and locked into place. Try a new cassette. |
| Display is blank or frozen | Software glitch; low battery | Remove and reinsert batteries to reset the device. Replace batteries if low. |
7. Specifications
| Feature | Description |
|---|---|
| Brand | Dymo |
| Model | LM160 |
| Compatible Label Tapes | DYMO D1 (6mm, 9mm, 12mm widths) |
| Keyboard Layout | QWERTY |
| Display | Monochrome LCD |
| Power Source | 6 x AAA Batteries (not included) |
| Connectivity Technology | Wi-Fi (as per product data) |
| Printer Output | Monochrome |
| Form Factor | Portable, Handheld |
| Product Dimensions (L x W x H) | 24 cm x 18 cm x 12 cm (approximate package size) |
| Product Weight | 0.661 kg (approximate package weight) |
| Origin | Mainland China |
8. User Tips
- For optimal performance and battery life, use high-quality alkaline batteries.
- Always ensure the label tape cassette is securely inserted to prevent printing errors or jams.
- When printing multiple labels, consider using the copy function (if available) to save time and ensure consistency.
- Experiment with different font sizes and styles to find the best readability for your specific labeling needs.
- Keep the label maker in a clean, dry environment to prolong its lifespan.
9. Warranty and Support
For warranty information and customer support, please refer to the documentation provided by the manufacturer or contact your point of purchase. Ensure you retain your proof of purchase for any warranty claims.
