1. Product Overview
The JIKONG Lithium battery intelligent protection board is a management system designed for large capacity series lithium battery packs. It features voltage acquisition, high current active balancing, overcharge, over-discharge, over-temperature protection, coulomb meter, Bluetooth communication, and optional GPS remote functions. It is suitable for various battery types including lithium iron phosphate, ternary lithium, and lithium titanate batteries.
This protection board utilizes energy transfer active balancing technology with independent intellectual property rights, achieving a maximum continuous 1A/2A balance current. This high current active equalization technology ensures battery consistency, improves range, and delays battery aging. The board is compact, easy to operate, and full-featured, making it suitable for battery packs in small sightseeing vehicles, mobility scooters, shared cars, high-power energy storage, base station backup power supplies, and solar power stations.


2. Package Contents
Please check the package contents carefully upon receipt:


- 1 x BMS unit
- 1 x Sampling line (70cm)
- 1 x NTC temperature sensor (40cm)
- 1 x Switch (50cm)
- Optional accessories: USB-TTL RS485 Cable, 3.2 Inch LCD, 4.3 Inch LCD
3. Setup & Installation
3.1. Device Activation
Before powering on the protection board, ensure the balance cable is correctly connected and that the P- and B- terminals are properly connected. Verify that the protection board is securely fixed to the battery cells. Incorrect connection can lead to abnormal operation or damage.
The protection board does not have a power-on control switch. It is designed for charging activation mode (charger voltage 2V higher than battery voltage). After battery assembly, connect the charger to activate the protection board.
For models with a display screen and button, activation can also be done by inserting the cable into the display interface and pressing the button.
3.2. APP Installation
The JIKONG BMS features a mobile APP for Android and iOS systems. Scan the QR code below to download the official APP. Android version 7 or higher is required.

3.3. Wiring Instructions
The JK-BxA8S-20P series protection board is suitable for 3-8 series lithium battery packs. The specific wiring method varies depending on the number of cells in your battery pack. Always ensure correct polarity and secure connections.


General Wiring Steps:
- Connect all balance cables to the battery cells, ensuring correct order from B1 to B+.
- Insert the balance cable connector into the BMS.
- Connect the main negative (B-) line from the battery to the B- terminal on the BMS.
- Connect the main positive (P-) line from the battery to the P- terminal on the BMS.
- Connect the load and charger to the P- and P+ terminals as shown in the diagrams.


4. Operation
The JIKONG BMS offers various functions configurable via the mobile APP or optional display screens.
4.1. Active Equalization
The BMS uses active equalization to transfer energy from high-voltage cells to low-voltage cells, ensuring voltage balance with minimal energy loss. Before using this function, set basic battery parameters (cell count, capacity, trigger differential pressure, voltage/current calibration) in the APP.
The balance current can be set to 1A or 2A. It is recommended that the balance current does not exceed 0.2C of the battery capacity. If not needed, the balancing function can be turned off in the APP.


4.2. GPS & Display Interface
The BMS has a reserved GPS port for optional GPS modules, allowing for battery location tracking. It also supports optional JIKONG display screens (3.2-inch or 4.3-inch LCD) to view battery information directly.



4.3. Heating Function (Optional)
The BMS supports an optional heating function to warm the battery in low-temperature conditions, preventing reduced activity and charging/discharging issues. The heating current is 20A. Users can control this function via the APP. It is recommended to use a temperature control switch (45°C to 65°C normally closed) in series with the heating circuit for secondary protection.
4.4. Alarm Function (Optional)
The BMS supports an optional alarm function that provides external alerts when safety risks such as overtemperature, overcharge, or over-discharge are detected.
4.5. Battery Parallel Function (Optional)
This function allows for parallel connection of battery packs, suitable for energy storage applications. It requires synchronous use with parallel modules and disabling the 'charging current limiting' function in the APP.
4.6. ACC Detection Function (Optional)
The BMS supports optional ACC detection for enabling discharge. This can be achieved by applying a voltage (20V-100V) between ACC+ and ACC- or by short-circuiting them. A charger detection function (C_detect+ and C_detect-) is also available for enabling charging.
4.7. Communication Functions (Optional)
The BMS supports optional CAN and RS485 communication functions. Users can select these based on their requirements and configure the address and communication protocol via the APP. Refer to the JIKONG Protection Board communication protocol document for details.



4.8. Intelligent Sleep
The BMS includes an intelligent sleep function to reduce energy consumption when in standby (charging/discharging current less than 1A for 26 consecutive hours). It can be activated by button or charger.
5. Protection Features (Troubleshooting)
The JIKONG BMS is equipped with comprehensive protection features to ensure battery safety and longevity. When a protection event occurs, the BMS will take action to prevent damage and will recover automatically once conditions return to normal.
- Overcharge Protection: Prevents battery cells from being overcharged. Users can set overcharge protection and recovery voltages via the APP.
- Discharge Undervoltage Protection: Prevents battery cells from being over-discharged. Users can set undervoltage protection, recovery, and automatic shutdown voltages via the APP.
- Charge Overcurrent Protection: Protects against excessive charging current. Users can set continuous charging current, delay, and release times via the APP.
- Discharge Overcurrent Protection: Protects against excessive discharging current. Users can set continuous discharge current, delay, and release times via the APP. (Note: Maximum continuous discharge current should not exceed 200A).
- Overtemperature Protection: Protects against high temperatures during charge and discharge. Users can set overtemperature protection and recovery values via the APP.
- Low Temperature Protection: Protects against low temperatures during charge. Users can set low temperature protection and recovery values via the APP.
- Short Circuit Protection: Provides protection against short circuits. Users can set delay and recovery times via the APP. If a short circuit occurs during initial charging or discharging, increasing the delay time may resolve it.
- Emergency Switch: In case of over-temperature, over-discharge, over-charge, or cell drop issues, activating the emergency switch via the APP will allow 30 minutes of continued charge/discharge operation, providing emergency use time.
6. Specifications
6.1. General Specifications
| Parameter | Value | Unit |
|---|---|---|
| Supply Voltage | 7.5-36 | V |
| Operating Power Consumption | <900 | mW |
| Operating Temperature | -30-70 | °C |
| Maximum Number of Collection Strings | 8 | Strings |
| Maximum Balancing Current | 1A / 2A | A |
| Maximum Charging Current | 200 | A |
| Maximum Discharge Current | 200 | A |
| Maximum Instantaneous Current | 400 | A |
| Maximum Internal Loop Resistance | 0.35 | mΩ |
| Protective Plate Size | 152.25*127.26*15.6 | mm |
| Finished Weight | 424 | g |

6.2. Dimensions



6.3. Default Parameters
The BMS comes with default parameters optimized for different battery chemistries (Li-ion, LiFePO4, LTO). These can be adjusted via the APP.
| Parameter | Li-ion Default | LiFePO4 Default | LTO Default | Unit |
|---|---|---|---|---|
| Balancing Initial Voltage | 3 | 3 | 2 | V |
| Max Balancing Current | 1A / 2A | 1A / 2A | 1A / 2A | A |
| Unit Overcharge Voltage | 4.2 | 3.6 | 2.7 | V |
| Single Overcharge Protection Recovery | 4.18 | 3.55 | 2.65 | V |
| Monomer Undervoltage Protection | 2.82 | 2.6 | 1.8 | V |
| Single Undervoltage Protection Recovery | 2.85 | 2.65 | 1.85 | V |
| Automatic Shutdown Voltage | 2.8 | 2.5 | 1.7 | V |
| Charging Overtemperature Protection | 70 | 70 | 70 | °C |
| Charging Low Temperature Protection | -20 | -20 | -20 | °C |
| MOS Overtemperature Protection | 100 | 100 | 100 | °C |
7. Maintenance
To ensure optimal performance and longevity of your JIKONG BMS, regular maintenance is recommended:
- Regular Checks: Periodically inspect all wiring connections for tightness and signs of wear or corrosion.
- Software Updates: Keep the JIKONG APP updated to the latest version to benefit from new features and bug fixes.
- Parameter Review: Occasionally review the BMS parameters in the APP to ensure they are still appropriate for your battery configuration and usage patterns.
- Cleanliness: Keep the BMS unit clean and free from dust and debris to ensure proper heat dissipation.
- Environmental Conditions: Operate the BMS within its specified temperature range (-30°C to 70°C) to prevent damage.
8. User Tips
- Check Model Numbers: When ordering or configuring your BMS, always double-check the model number (e.g., JK-B2A8S20P vs. JK-B2A8S20PHC) to ensure compatibility with your battery setup and desired features.
- APP Customization: Utilize the JIKONG APP to fine-tune protection parameters and balancing settings according to your specific battery type and usage requirements.
- Heating Function in Cold Climates: If operating in extremely cold environments, consider using the optional heating function to maintain battery performance and prevent damage.
- Secure Connections: Always ensure all wiring connections are secure and properly insulated to prevent short circuits and ensure reliable operation.
9. Frequently Asked Questions (FAQ)
- Q: What is the difference between JK-B2A8S20P and JK-B2A8S20PHC?
- A: The primary difference lies in their features. The 'HC' in JK-B2A8S20PHC typically indicates additional functionalities such as a heating function and CAN communication, which might be optional or standard depending on the specific product variant. Always refer to the product configuration table for detailed differences.
10. Warranty & Support
For warranty information, technical support, and service inquiries, please contact JIKONG BMS Store directly or refer to the official JIKONG website. You can also find additional resources and documents, including the full user manual PDF, at the following link: