LAUNCH Creader 529

Contents

LAUNCH Creader 529 OBD II Scanner User Manual

Model: Creader 529

1. Introduction

The LAUNCH Creader 529 OBD II Scanner is designed for DIY users and small service workshops. It supports reading and clearing Diagnostic Trouble Codes (DTCs) and reading data streams. With built-in help menus and code definitions, diagnosing and repairing the Check Engine Light is made easier.

This scanner can print diagnostic records by connecting to a PC and can be updated via USB cable to ensure the latest software version.

Note: The scanner may automatically reset if disturbed by strong static electricity. This is a normal reaction.

The Creader 529 is designed to work with all OBD II compliant vehicles, including those with Controller Area Network (CAN). EPA regulations require all 1996 and newer vehicles (cars and light trucks) sold in the United States to be OBD II compliant. This includes American, Asian, and European vehicles. Some 1994 and 1995 gasoline vehicles may also be OBD II compliant.

1.1 Verifying OBD II Compliance

To verify if a 1994 or 1995 vehicle is OBD II compliant, check the Vehicle Emissions Control Information (VECI) Label. This label is typically located under the hood or by the radiator. If the vehicle is OBD II compliant, the label will state “OBD II Certified”.

LAUNCH Creader 529 All-in-One Features
Figure 1.1: LAUNCH Creader 529 All-in-One Features, including Read Codes, Erase Codes, Live Data, Freeze Frame, I/M Readiness Status, O2 Sensor Test, On-board Monitor System Test, VIN Information, Prints Data, DTC Lookup, Data Record and Replay, EVAP System, and Lifetime Free Update.

Government regulations mandate that all OBD II compliant vehicles have a standard 16-pin Data Link Connector (DLC). This is where diagnostic tools connect to the vehicle's on-board computer. The DLC is usually located within 12 inches of the center of the instrument panel (dash), under or around the driver's side. For some Asian and European vehicles, it might be behind the ashtray.

OBD II 16-pin Data Link Connector (DLC) Diagram
Figure 1.2: Diagram of the 16-pin OBD II Data Link Connector (DLC).

Note: Some 1994 and 1995 vehicles may have 16-pin connectors but are not OBD II compliant. Only vehicles with a VECI label stating “OBD II Certified” are truly OBD II compliant.

2. Safety Precautions and Warnings

To prevent personal injury or damage to vehicles and/or the test equipment, please read this manual carefully and observe the following safety precautions:

  • Always perform automotive testing in a safe environment.
  • Do not attempt to operate or observe the tool while driving a vehicle. This can cause driver distraction and lead to accidents.
  • Wear safety eye protection that meets ANSI standards.
  • Keep clothing, hair, hands, tools, and test equipment away from all moving or hot engine parts.
  • Operate the vehicle in a well-ventilated work area as exhaust gases are poisonous.
  • Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
  • Use extreme caution when working around the ignition coil, distributor cap, ignition wires, and spark plugs, as these components create hazardous voltages.
  • Put the transmission in P (for A/T) or N (for M/T) and ensure the parking brake is engaged.
  • Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
  • Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
  • Keep the test equipment dry, clean, and free from oil/water or grease. Use a mild detergent on a clean cloth to clean the outside of the test equipment when necessary.

3. Components & Controls

LAUNCH Creader 529 Product Layout and Buttons
Figure 3.1: LAUNCH Creader 529 Product Layout with labeled components and buttons.
No.NameNotes
1Cable with OBD II CONNECTORConnects the scanner to the vehicle's Data Link Connector (DLC).
2LCD SCREENShows menu and submenus and test results.
3I/M BUTTONQuick access to I/M readiness function. Deletes diagnostic records in the Print function module.
4RETURN BUTTONReturns to previous menu.
5UP BUTTONScrolls UP through menu and submenu options.
6RIGHT BUTTONScrolls RIGHT through menu/submenu options. Scrolls to NEXT page when linked to a vehicle.
7OK BUTTONConfirms a selection or action from a menu list.
8USB PORTConnects the scanner to a computer via USB cable for upgrade or printing.
9DOWN BUTTONScrolls DOWN through menu and submenu options.
10LEFT BUTTONScrolls LEFT through menu/submenu options. Scrolls to PREVIOUS page when linked to a vehicle.
11HELP BUTTONProvides detailed descriptions/tips for diagnostics.
12LED for different DTC typesVisual aids for engine system conditions: Green (No Fault Code), Yellow (Pending Fault Code), Red (Permanent Fault Code).

4. Setup (Initial Use)

4.1 Connection

  1. Turn the vehicle's ignition off.
  2. Locate the vehicle's 16-pin Data Link Connector (DLC).
  3. Plug the diagnostic cable of the scanner into the vehicle's DLC. The cable connector is keyed and will only fit one way. If you have problems, rotate the connector 180 degrees and try again.
  4. Turn the ignition on. The engine can be off or running.
  5. The system will automatically turn on and navigate to the Job menu screen.

Caution: Do not connect or disconnect any test equipment with the ignition on or engine running.

4.2 Job Menu

The Job Menu provides access to the following function modules:

ModuleDescription
DIAGNOSEConfigures the scanner as a professional OBD II code reader.
I/M ReadinessIndicates whether emissions-related systems are operating properly and are ready for Inspection and Maintenance testing.
REVIEWReviews or deletes recorded DTCs, Data Streams, and Freeze Frame data.
LOOKUPRetrieves desired DTCs and displays detailed definitions and diagnostic solutions.
PRINTPrints diagnostic records saved during a diagnostic session. Requires USB connection to a PC.
HELPProvides general knowledge about OBD, Data stream, and I/M readiness.
SETUPAllows adjustments and settings to configure the scanner.
INFOViews detailed information about the scanner (software/hardware version, serial number).

5. Operating Instructions

5.1 Start Diagnostics

After connecting the scanner to the vehicle's DLC, select [Diagnose] from the Job Menu and press [OK]. The scanner will automatically check the vehicle's computer to determine the communication protocol. Once established, the Monitor Status screen will display.

Note: A PROTOCOL defines rules for data transmission. The Creader 529 supports ISO 9141, Keyword 2000, J1850 PWM, J1850 VPW, and CAN protocols.

5.2 Read Codes

This function allows you to view Diagnostic Trouble Codes (DTCs) retrieved from the vehicle's on-board computer.

  1. From the Diagnostic Menu, select [Read Codes] and press [OK].
  2. A screen will prompt you to select the car manufacturer. Press [OK] to enter the selection.
  3. Use the UP/DOWN buttons to select the manufacturer and the LEFT/RIGHT buttons to navigate pages. Press [OK] to confirm.
  4. The scanner will display the DTCs found. The screen will show the DTC number, its sequence, total count, type (Generic Current, Generic Pending, Generic Permanent), and definition.
  5. Press [HELP] to view diagnostic tips/solutions for the current DTC.
  6. After viewing all codes, press the RETURN button to go back to the Diagnostic Menu.
LAUNCH Creader 529 Multi-functions Display
Figure 5.1: Multi-functions display showing I/M Readiness, Vehicle Information, and OBDII Review Data options.

5.3 Erase Codes

This function clears Diagnostic Trouble Codes (DTCs) from the vehicle's computer memory.

  1. From the Diagnostic Menu, select [Erase Codes] and press [OK].
  2. A confirmation message will appear: “Clear/Reset Emission Related Diagnostic Information. Are you Sure?” Press [OK].
  3. Follow the on-screen prompts to turn the ignition on with the engine off, then press [OK] to clear the DTCs.

Note: Erasing DTCs also clears


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.