1. Introduction
The GVDA GD101B Socket Tester Pro is designed for the polarity detection of three-hole power socket wiring and the protection function detection of leakage switches (RCD). It provides a quick and accurate method to detect the wiring condition of a socket, helping to identify issues that could lead to electric shocks, electrical fires, or abnormal equipment operation. This device is widely used in fire protection, safety supervision, home improvement, laboratory, factory, and general home line inspection and maintenance.
2. Safety Information
Warning: Please read this instruction manual carefully before use and strictly adhere to all safety rules, cautions, and warnings listed herein to prevent potential electric shock or personal injury.
- Before each use, carefully inspect the tester for any damage. If damage is found, discontinue use immediately and send it for repair.
- To verify the tester's functionality, plug it into a known correctly wired socket and confirm that the test functions operate as expected before proceeding with other tests.
- When performing switch detection, ensure the wiring is correct for normal operation.
- When conducting the leakage switch (RCD) test, always turn off all electrical appliances connected to the circuit to prevent any harm from power outages. If testing in public areas, ensure prior approval is obtained.
- If a socket wiring error is detected, consult a professional electrician to rectify the wiring.
3. Product Overview
The GVDA GD101B Socket Tester Pro is a plug-and-play device featuring line detection and leakage protection. It offers multiple functions including color display, socket polarity detection, leakage tripping detection, and auto power-off for safe and easy use.


3.1 Panel Introduction
Familiarize yourself with the components of the socket tester:

- Low battery indication: Icon illuminates when battery power is low.
- Socket pin indication: Visual representation of the socket pins.
- Zero-live voltage test value display: Shows the voltage between the live and neutral lines.
- Power on/off: Button to turn the device on or off.
- Socket wiring status display area: Indicates the detected wiring condition (e.g., correct, missing ground).
- Zero-earth voltage test value display: Shows the voltage between the neutral and earth lines.
- RCD leakage current: Indicates the RCD test current.
4. Setup
4.1 Battery Installation
The device requires 2 x 1.5V AAA batteries (not included) for operation.

- Before using, open the battery cover located on the device.
- Install two AAA batteries, ensuring correct polarity.
- Close the battery cover securely.
5. Operation
5.1 Power On
Long press the power button (ON/OFF) for 2 seconds to turn the device on.
5.2 Basic Socket Testing
Plug the product into the socket to be tested. The device will automatically display the current socket line status and voltage.

5.3 RCD Test (Leakage Tripping Detection)
Warning: Before performing the RCD test, ensure all electrical appliances on the circuit are turned off and permission is obtained to avoid any harm from power outages.
Insert the tester into the three-hole socket. When the display prompts "The wiring is correct", press the RCD button for less than 3 seconds. A normal leakage switch will trip. If no tripping occurs, it indicates that the leakage switch has failed or is missing. In such cases, seek professional electrician maintenance immediately.

5.4 Socket Polarity Detection
The tester automatically detects and displays the zero-live voltage (L-N) and zero-earth voltage (N-E) to indicate socket polarity. A high definition color display ensures clear visibility of these values even in dark environments.


6. Test Status Analysis
The socket wiring status display area provides clear indications of various wiring conditions:

- The wiring is correct: Indicates proper wiring. (Reference values shown on the right are for display only).
- Missing zero line: The icon in the dotted line will flash an alarm.
- Missing ground: The icon in the dotted line will flash an alarm.
- Fire ground reverse: The icon in the dotted line will flash an alarm.
- Fire zero reverse: The icon in the dotted line will flash an alarm.
- Mismatch and lack of land: The icon in the dotted line will flash an alarm.
6.1 Special Attention
- The normal voltage range for the zero-live line (L-N) is typically within ±10% of the local standard voltage. If the reading is significantly too high or too low, it may indicate an excessive circuit load or an issue with the power supply.
- The normal voltage for the zero-earth wire (N-E) should ideally be less than 2V. A higher reading might suggest current leakage, an imbalance in the three-phase sequence, or signal interference within the circuit.
7. Specifications
| Parameter | Value |
|---|---|
| Plug Type | EU plug |
| Zero-live voltage measure (L-N) | 30-250V / (50-60HZ) |
| Zero-earth voltage measure (N-E) | 0.1-10V / (50-60HZ) |
| Working environment temperature | 0°C-40°C |
| Working environment humidity | 20%-70% |
| Storage environment temperature | 10°C-50°C |
| Storage environment humidity | 20%-80% |
| RCD current | >30mA |
| RCD working voltage | 220V±20V |
| Battery | 2 x 1.5V AAA (not included) |
| Product weight | 82g |
| Package weight | 110g |
8. User Tips
- Always ensure the tester's display is clear and readable before interpreting results, especially in varying light conditions.
- For consistent and reliable RCD test results, always disconnect all other loads from the circuit being tested.
- If you encounter any unexpected readings or persistent errors, refer to the troubleshooting section or consult a qualified electrician.
9. Maintenance
9.1 Battery Replacement
To prevent electric shock or injury from incorrect readings, replace the batteries immediately when the low battery symbol appears on the display. To avoid electric shock or personal injury, always turn off the power and ensure the socket tester is removed from the measurement circuit before opening the battery cover to replace new batteries.
10. Warranty and Support
This product is guaranteed for 18 months from the date of purchase. The warranty does not cover fuses, disposable batteries, accessories (such as packaging boxes), or damage to the instrument due to accidents, neglect, abuse, alterations, pollution, or abnormal operating conditions.
This manual is subject to change without notice. While the contents of this manual are considered correct, if you find any errors or require further assistance, please contact the manufacturer or seller.
The company is not responsible for accidents and hazards caused by user's wrong operation. The functions described in this manual should not be used as a reason to use the product for a special purpose not intended by the manufacturer.
For the complete user manual, please refer to the official PDF document: GVDA GD101B User Manual (PDF)