1. Introduction
Dear Customer,
Thank you for choosing the MEKEDE car multimedia system. To ensure effective and safe use of your device, please read these instructions carefully before use.
Note: Due to continuous product improvement, some descriptions in this manual may differ from the actual equipment. Specifications are subject to change without notice.
Safety Measures
- It is forbidden to watch videos or other visual content while driving. Active use of the system during driving is not recommended as it can reduce attention and may result in accidents.
- The unit is designed for use in cars with a 12V power supply and a minus ground. Do not install the system in a bus or truck with an on-board voltage of 24V. This may cause damage to the device.
- Use a special cleaning device to care for the screen.
- To avoid overheating, do not allow direct exposure to sunlight and do not install near the heating system. Operating temperature is between 0°C and 35°C. If the temperature inside the vehicle is too high, cool the interior before switching on. Do not operate the unit at very low temperatures; wait until the interior and vehicle temperature returns to normal.
- Only use the provided fasteners (screws, mounting frames, etc.) for installation. The use of other fasteners may result in damage to the system, and this is not covered by the warranty.
- Installation and connection of the device shall be performed by a qualified specialist or specially trained staff of the service center.
- Do not reset to factory settings on your own unless in extreme cases, as this will cause loss of your settings, which may result in incorrect operation of the system.
- Violation of the above items and improper use may cause the system to malfunction. In this case, warranty service will not be performed.
2. Technical Specifications
| Attribute | Specification |
|---|---|
| Mounting Size | 9"/10" |
| Screen Resolution | 1280x720 IPS |
| Display Size | 9" or 10" |
| CPU | UIS7862 1.8GHz 8-core (2 cores ARM Cortex A75 + 6 cores ARM Cortex A55) |
| RAM | DDR3 2GB/3GB/4GB/6GB/8GB |
| ROM | 32GB/64GB/128GB |
| Operating System | Android 11 |
| Maximum Output Power | 4 x 45 W |
| Sound Amplifier | TDA 7388/Toshiba 001 (M200S M300S), TDA7851/7850/7838 (M400S M500S M600S M700S) |
| Chip FM Tuner | NXP TEF6686 |
| DSP Processor Features | Low Pass Filter, Tone Compensation, Balance Mode, Surround Sound Mode, Extended Equalizer settings (32 bands) |
| CarPlay / Android Auto | Supported (add-on Car Link) |
| Video Format | RMVB, MKV, MOV, WMV, AVI, MPG, TS, H.264 codec and others. |
| Audio Format | MP3, WMA, WAV, OGG, FLAC |
| GPS | Built-in receiver with external antenna |
| Software for Navigation | Support |
| Wi-Fi | Support |
| 4G LTE | Support |
| BT | A2DP and BT address book transfer |
| Steering Wheel Control | Support |
| ADAS DVR | Activation in the settings menu |
| AHD HD Reversing | Automatic activation of video input |
| Voltage | 12 V |
| Item Weight | 1.46kg |
| Material | Metal and glass |
| OSD Language | Multiple languages including English, German, French, Spanish, Italian, etc. |
3. Package Contents
The package includes the following items:

Image showing the main unit, power cable, RCA cables, reversing camera cable, USB cables, and GPS antenna. Specific cables vary by model (M90S/M95S vs. M200S-M800S).
- Main Unit (Machine)
- Power Cable
- RCA Cable
- Reversing Camera Cable
- USB Cable (2 or 3 depending on model)
- GPS Antenna
- Audio Out (for M200S-M800S models)
- 4G Antenna (for M200S-M800S models)
- MIC (for M200S-M800S models)
4. Setup Instructions
Pre-Installation Check
Before installation, please verify if your original car player has a navigation function or an amplifier. If it does, this unit might not be compatible. Refer to the image below for examples of incompatible and compatible dashboards.

Image showing car dashboards. The top image indicates 'Can't Install' for a car with a built-in navigation screen. The bottom images indicate 'Can Install' for cars with basic radio units.
Connection Diagram
Ensure all cables are connected correctly as per the diagram. Improper connections can lead to malfunction.

Detailed wiring diagram for the car multimedia system, showing connections for speakers, steering wheel control, reverse detecting line, ACC, GND, ANT power, and various optional accessories like 4G antenna, USB, and fiber optic connections.
Rear Camera Connection
There are two methods for connecting the rear camera:
Without CANBUS Box:
Connect the reversing control wire to A5, the camera power to the reverse light (12V), and the camera ground to the car ground.
With CANBUS Box:
If you have a CANBUS box and the reverse control line (A3 area) is already connected, the yellow line connection for reversing control is not needed. Connect ACC to A3 ACC, and ensure the two red wires from the camera power are connected together, but not with other wires. Connect the camera ground to the car ground.
CANBUS Box Setup (If applicable)
If your car's original functions (like steering wheel control) are not working, you may need to set up the CANBUS type. Check your CANBUS photo and select the corresponding type in the settings.
Setup Steps:
- Connect the CANBUS box as shown in the picture.
- Go to Settings > Car Settings > Factory (Password: 8888).
- Select the appropriate CANBUS type for your vehicle.
Cooling Fan Setup
The cooling fan helps maintain optimal operating temperature. To activate it:
- Connect the cooling fan cable to the designated port on the back of the unit.
- Go to Settings > Device > Sound.
- Turn AMP ON/OFF to ON.
- The cooling fan should now start working.

Image illustrating the connection of the cooling fan and the menu navigation steps to enable it: Settings -> Device -> Sound -> AMP ON/OFF.
SIM Card Insertion (for 4G LTE models)
To use 4G LTE functionality:
- Push the iron plate down and open the SIM card slot.
- Insert the SIM card with the chip facing the system module and the bevel outward.
- Pull up the iron plate to fix the SIM card in place.

Image showing the correct orientation and method for inserting a 4G SIM card into the car radio's slot.
5. Operating Instructions
Front Panel Controls (M-S Series)
- MIC: Microphone
- RST: Emergency reassembly of equipment
- Home Button: Input/output switch/live switch/sound switch
- Back Button: Return to main menu
- Volume Up/Down: Increase/Lower the volume
Switching the Appliance On/Off
After switching off the ignition and starting the engine, the multimedia system automatically switches on. The display shows the initial screen. The unit activates automatically after the engine is switched off.
Touch Screen Operation
The unit is equipped with an interactive touchscreen display. Before using it for the first time, remove the sealed plastic membrane. Otherwise, the touch screen may not function properly.
- Touch: Click the necessary item to start the plugin (signal source) or select the menu item (option).
- Double Tap: A quick double touch allows you to resize when viewing images.
- Touch & Hold: Click and hold the item for 2 seconds to trigger an additional action available for that item.
- Dragging: Touch and hold the selected item, then drag it onto the screen.
- Moving: Rotate the screen with your finger and keep your finger touched, move your finger in the right direction throughout the screen.
- Scroll through: Move your finger on the screen in the direction you need to and let go. Rotation can be stopped by touching the screen, or wait until the motion stops itself.
Attention! Do not use metal or sharply sealed objects to control sensory interactive display. Also, do not apply excessive force when touching the screen.
Main Menu Interface
The main interface allows you to customize the position of icons and freely edit applications for easy operation. The system offers multiple main menu styles.

Image showing the main user interface with navigation, music, radio, and other applications.
Video demonstrating the user interface, including navigation through home screens, music playback, radio tuning, video playback, Bluetooth calling, Wi-Fi connection, file management, and language settings.
Changing Wallpaper:
You can set a picture or photo as the background for the main screen. Choose from pre-installed options or images/photos stored on a USB memory device or SD card.
Main Menu Styles (M200S-M800S models):
These models offer five optional main menu styles. To change:
- Go to Settings > Factory (Password: 3368).
- Find "Home Launcher Selection".
- Select your desired main menu style.
FM/AM Radio
To access the radio, click the "Radio" icon on the main menu. You can manually tune or use automatic search. The system supports RDS (Radio Data System).
- LOC mode: Radio will only receive stations with a strong signal.
- DX mode: Radio will receive all stations in the current range.
- You can save favorite stations.
Music / Video Playback
Connect a USB storage device or insert an SD memory card. Press the "Music" icon for music playback or "Video" icon for video playback.
Supported video formats: MP4, AVI, MMV, MOV, MKV, MPEG, RMVB, etc.
Attention! For safety, video playback is restricted while the car is in motion. To view video, stop in a safe place and apply the handbrake.
Bluetooth (BT) Function
To access Bluetooth, click the "BT" icon on the main menu. This allows for hands-free calling and music streaming (A2DP).
- Open your phone's Bluetooth settings and search for new devices.
- Select the car radio device (e.g., "Car BT").
- Confirm connection on your phone and enter the PIN (default: 1234 or 0000) if prompted.
- The system screen will show "connected" upon successful pairing.
CarPlay / Android Auto (Car Link)
Car Link is an add-on that allows you to use your iPhone (CarPlay) or Android phone (Android Auto) with the car radio, enabling navigation, calls, messages, and music without distraction.

Image detailing the connection steps for Wireless Car-Play (iOS system) via Bluetooth and Wireless Auto (Android system) via USB cable, including authorization prompts.
Wireless CarPlay (iOS System) Connection Steps:
- Connect your iPhone via Bluetooth.
- Tap on "Car Link" on the car radio. Your iPhone will ask for authorization; authorize the connection and wait.
Android Auto Connection Steps:
- Connect your Android phone and car radio with a USB cable.
- Tap on "Car Link" on the car radio. Your Android phone will ask for authorization; authorize the connection and wait.
Split Screen
The split screen feature allows you to display two applications simultaneously, such as navigation and music. To exit split screen mode, pull the icon between the two screens to the right.

Image showing the split screen feature, allowing two applications (e.g., online video and map, or music and map) to be displayed side-by-side for multitasking.
GPS Navigation
The unit features a built-in global positioning system with omnidirectional map display, synchronous real-time traffic display, and accurate positioning. Supported navigation apps include Navitel, IGO, Yandex, and Google Maps.

Image displaying the GPS navigation interface with various supported navigation applications like iGO, Sygic, Yandex, Google, and Waze.
Language Settings
To change the system language:
- Go to Settings > Language & Input.
- Select your preferred language from the list.
- You can reorder languages by dragging them to the first position.

Image showing the language settings menu, where users can select and prioritize different OSD languages.
Steering Wheel Control (SWC)
The head unit supports steering wheel control (SWC) for safety and convenience, allowing you to control music and hands-free calling without taking your hands off the wheel.

Image illustrating the steering wheel control function, showing a hand pressing a button on the steering wheel to control music playback on the car radio screen.
DSP Equalizer and Sound Enhancement
The built-in DSP (Digital Signal Processor) module allows for multi-dimensional surround lossless sound effects and high-definition audio-visual experience. You can adjust sound settings to your preference.

Image showing the DSP Equalizer interface with various frequency bands and preset sound effects like Standard, User, Rock, Soft, Classical, Pop, Jazz, Cinema.
- Equalizer Mode: Adjust frequency settings (32 bands) to customize sound. Presets like Rock, Soft, Jazz, Pop, Classical, Live are available.
- Automatic Volume Mode: Choose recommended settings for listener position (Driver Mode, Passenger Mode, Rear, Center) or adjust manually.
- Balance Mode: Adjust the volume ratio of speakers by moving a point on the car interior diagram.
- Bass Enhancement: Reverse high and low frequency tones and adjust boost factor.
Adjustable Lighting
The unit features adjustable button lighting. You can change the color and brightness, and select multiple color modes.

Image showing the 'Lantern settings' menu where users can adjust the color (Red, Green, Blue sliders) and brightness of the button lights, and choose between manual or automatic color change.
6. Additional Features (Optional Accessories)
The following features require additional accessories, which must be purchased separately.
DAB+ (Digital Audio Broadcasting)
EU DAB+ Radio Universal for all Android radios provides better sound quality and stronger signal, specifically for EU countries.

Image showing the DAB+ accessory, which is a USB dongle with an antenna, for enhanced radio reception.
OBDII (On-Board Diagnostics)
With the OBDII function, you can monitor real-time vehicle data and retrieve fault codes from the vehicle's computer.

Image showing the OBDII accessory (a WiFi Super OBD dongle) and its interface displaying engine management diagnostics and tools.
TPMS (Tire Pressure Monitoring System)
Once a TPMS is installed, sensors automatically monitor tire pressure and temperature, transmitting real-time statistics to the receiver.

Image showing both external and built-in TPMS sensors, along with a display of tire pressure and temperature readings.
ADAS DVR (Advanced Driver-Assistance Systems Digital Video Recorder)
The ADAS DVR provides anti-collision warning and lane departure warning features, predicting distance to the vehicle in front to enhance driving safety.

Image showing the ADAS DVR interface with vehicle collision warnings (Left Lane Departure, Front Collision, Right Lane Departure) and the ADAS DVR accessory.
AHD HD Reversing Video
The AHD (Analog High Definition) rear view camera provides clearer image quality compared to conventional cameras, automatically activating when reversing.

Image showing a 1080P AHD waterproof rear camera view with parking lines, demonstrating clear visibility day or night.

Image showing the 2053 chip AHD 1080P Rear View Cam accessory.
AV Output
The video output function allows you to display content on external screens, such as headrest displays, enabling rear passengers to watch HD video and audio.

Image showing RCA Port and HDMI-compatible accessories required for AV output functionality.
360° Camera
If you wish to add a 360° camera, it must be ordered along with your car radio, as a built-in 360° Camera Chip is required on the motherboard.
7. Maintenance
Cooling System
The unit is equipped with a powerful cooling fan to prevent overheating during long-term use or in high-temperature environments, ensuring stable operation and longer service life.

Image comparing car radios with and without a cooling fan, highlighting that MEKEDE machines include a back cover cooling fan for longer service life.

Image showing the high-efficiency cooling fan and its interface, which can be automatically or manually controlled based on temperature.
8. Troubleshooting
If you encounter a problem, try disconnecting and then reconnecting your device. Use the special key to press the Reset button. If this does not solve the problem, refer to the table below. Otherwise, check that the device is properly connected or consult your authorized dealer.
| Symptom | Probable Cause | Solution |
|---|---|---|
| Device doesn't turn on. | Ignition key is not in the "On" position. | Turn the key to the "On" position. |
| Device doesn't turn on. | Overheated fuses (15A). | Check the circuit breaker in the device; if not working, replace it with a good one of the same nominal size. |
| Device doesn't turn on. | Incorrect connection of the electrical supply (black and yellow wires). | Check the connection of the electrical supply. |
| Phonebook contacts are not transferred. | No rights on the phone (Bluetooth). | After connecting the phone to the device, go to the BT settings on the phone and authorize the transfer of the phone book. |
9. Warranty and Support
MEKEDE products come with a 365-day free replacement warranty from the date of receipt confirmation. If a product problem occurs within 15 days, you are eligible for free return and refund, or a direct replacement. For issues beyond 15 days but within the 365-day warranty period, please contact customer service for assistance.

Image illustrating the 365 Days free replacement warranty process: Buyer contacts seller, confirms quality problems, buyer returns item, seller receives return, seller sends a new item.
We provide updates for Firmware, Software, UI, and GPS Navigation maps for FREE. If you provide a 5-star review and share installation photos, your warranty can be extended to 2 years.
10. User Tips
- Always ensure your vehicle's ignition is in the 'On' position when attempting to power on the car radio.
- For optimal performance and longevity, ensure the cooling fan is properly installed and activated, especially in warmer climates or during extended use.
- When connecting your smartphone via Bluetooth for calls or music, remember to grant necessary permissions for phonebook access and media sharing on your device.
- If experiencing issues with optional accessories like DAB+ or OBDII, double-check their connections and ensure they are correctly enabled in the unit's settings.
- Regularly check for firmware and software updates provided by MEKEDE to ensure you have the latest features and improvements.