1. Introduction
This manual provides detailed instructions for the safe and efficient operation of your VEVOR Fiber Laser Marking Machine. This portable machine is designed for precision marking on various metal and some non-metal materials, producing clear and permanent engravings that will not fade. Featuring air-cooled cooling, a compact design, and high reliability, it is an ideal tool for a wide range of applications.
Figure 1: VEVOR Fiber Laser Marking Machine
2. Safety Information
Operating a laser marking machine requires strict adherence to safety protocols to prevent injury and damage. Please read and understand all safety warnings before operation.
2.1 General Safety Precautions
- Always wear the provided laser safety goggles during operation to protect your eyes from laser radiation.
- Ensure the work area is well-ventilated to dissipate fumes and particles generated during marking.
- Never look directly into the laser beam or at reflections from shiny surfaces.
- Keep flammable materials away from the laser's path.
- Do not operate the machine if any covers are removed or safety interlocks are bypassed.
- Ensure the machine is properly grounded.
- Only trained personnel should operate and maintain the laser machine.
2.2 Material Safety
- Avoid marking materials that produce toxic fumes or are highly flammable when exposed to laser energy.
- Be aware of the material composition before marking to prevent unexpected reactions.
3. Product Features
- Precision Marking: Fiber laser life can reach 100,000 hours. High beam quality, base mode (TEM00) output, focused spot diameter less than 20µm. The divergence angle is 1/4 of the semiconductor pump laser, resulting in finer single lines.
- Galvanometer System: Features a high-speed digital scanning oscillator system for fast processing, 2-3 times faster than traditional marking machines. It ensures high laser repetition frequency and high-speed marking without distortion.
- Portable and Energy-Saving: Small in size with low power consumption (less than 500W). The built-in air-cooled cooling method eliminates the need for bulky water-cooled units, allowing for a smaller footprint and easier installation.
- Elaborate Lifting Wheel: Equipped with a hidden lifting rod for high positioning accuracy. The wheel allows for easy adjustment of the galvanometric system's height.
- Powerful Software: Compatible with CorelDraw, AutoCAD, and other software files. Supports PLT, PCX, DXF, BMP, etc., and can directly use SHX, TTF fonts. Features include automatic coding, printing serial numbers, batch numbers, dates, barcodes, and two-dimensional codes, automatic jump number, and USB interface output control.
- Wide Application: Equipped with an optical isolator, effectively shielding reflected light. It can operate on highly reflective materials like gold, silver, copper, aluminum, and silicon without deviating from the positive center of the field mirror. Frequency and energy adjustment allow for color marking on different metals.
Precision Marking: 10µm Spot Size, 200x200mm Work Area, 10000 hours laser life.
High-speed Galvanometer System for faster processing.
Portable design with low power consumption (≤500W) and air-cooled cooling.
Lifting wheel for precise height adjustment.
Compatible with CorelDraw, EzCad2.10UNI, Auto-CAD, Photoshop.
Examples of various items marked by the laser machine.
4. Specifications
| Attribute | Value |
|---|---|
| Product Name | Fiber Laser Marking Machine |
| Brand Name | VEVOR |
| Origin | Mainland China |
| Certification | CE |
| Operating System | EZCAD2 |
| Laser Power | 30W / 50W |
| Working Area | 150*150mm (for 30W), 200*200mm (for 50W) |
| Power Supply | AC220V/50HZ |
| Input Current | 10A |
| Beam Quality | <1.6 |
| Cutting Depth | ≤1mm |
| Scanning Speed | 10000mm/s |
| Equipment Operating Power | ≤500W |
| Minimum Line Width | 0.01mm |
| Repetition Precision | ±0.0001mm |
| Laser Source Brand | Raycus |
| Laser Wavelength | 1064nm |
| Laser Repetition Frequency | 40KHz-60KHz / 50KHz-100KHz |
| Maximum Single Pulse Energy | 0.75(mJ) / 1(mJ) |
| Power Adjustment Range | 10%-100% |
| Minimum Character | 0.15mm |
| Marking Depth | 0.01-1.0mm |
| Cooling System | Air-cooled |
| Control Interface | USB |
| Continuous Working Time | Can work continuously |
4.1 Product Dimensions
Figure 2: Approximate dimensions of the laser marking machine.
5. Package Contents
Upon receiving your VEVOR Fiber Laser Marking Machine, please verify that all the following items are included:
- 1 x Laser Marking Machine
- 1 x Goggles
- 1 x Foot Switch
- 1 x Display Bracket
- 1 x Repair Tool
- 1 x Instructions Manual
- 1 x U Disk (containing software and drivers)
- 1 x Positioning Tool
- 1 x Power Input Line
- 1 x Data Transmission Line (USB cable)
- 1 x Connection (likely a cable or adapter)
- 1 x Marking Samples
Figure 3: Included accessories and components.
6. Setup Instructions
Follow these steps to set up your laser marking machine:
- Unpacking: Carefully remove all components from the packaging. Retain the packaging for future transport or storage.
- Placement: Place the laser marking machine on a stable, level surface in a well-ventilated area, away from direct sunlight and heat sources.
- Assembly (if required): Attach the display bracket if it's not pre-installed. Ensure all connections are secure.
- Power Connection: Connect the power input line to the machine and then to a grounded power outlet (AC220V/50HZ).
- Computer Connection: Connect the data transmission line (USB cable) from the machine to your computer.
- Software Installation: Insert the provided U Disk into your computer. Install the EZCAD2 software and any necessary drivers as per the instructions on the U Disk.
- Goggles: Always wear the provided safety goggles before powering on the machine.
7. Operating Instructions
This section outlines the basic steps for operating your laser marking machine.
- Power On: Turn on the main power switch on the machine.
- Software Launch: Launch the EZCAD2 software on your computer.
- Design/Import: Create your desired marking design within the software or import existing files (PLT, PCX, DXF, BMP, etc.).
- Material Placement: Place the material to be marked on the work platform.
- Focus Adjustment: Use the elaborate lifting wheel to adjust the height of the galvanometric system until the laser is properly focused on the material surface. The positioning tool can assist in achieving optimal focus.
- Parameter Settings: Adjust laser parameters (power, frequency, speed, marking depth) within the software according to the material type and desired marking effect.
- Preview (Red Light): Use the red light preview function in the software to ensure the marking area and position are correct.
- Start Marking: Initiate the marking process from the software. You may also use the foot switch for hands-free operation.
- Monitor Process: Observe the marking process. Do not leave the machine unattended during operation.
- Power Off: Once marking is complete, power off the machine and close the software.
7.1 Operation Demonstration Video
Video 1: Demonstration of the laser marking process on a metal surface, showing the precision and speed of engraving a detailed logo.
8. Maintenance
Regular maintenance ensures the longevity and optimal performance of your laser marking machine.
- Cleaning: Regularly clean the lens of the galvanometer system with a soft, lint-free cloth and appropriate lens cleaning solution. Ensure the work platform is free of debris.
- Ventilation: Keep the ventilation grilles on the machine clear of dust and obstructions to ensure proper airflow for the air-cooled system.
- Connections: Periodically check all electrical and data connections to ensure they are secure and free from damage.
- Software Updates: Keep your EZCAD2 software and drivers updated to the latest versions for best performance and compatibility.
9. Troubleshooting
Here are some common issues and their potential solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Laser not firing | Power not connected, emergency stop engaged, software error, laser source issue. | Check power connection, release emergency stop button, restart software/machine, contact support if laser source is suspected. |
| Poor mark quality (faint, blurry) | Incorrect focus, wrong laser parameters, dirty lens, material not suitable. | Adjust focus, optimize laser power/speed/frequency, clean lens, test on different material. |
| Machine not recognized by computer | USB cable issue, driver not installed/corrupt, software not running. | Check USB cable, reinstall drivers, ensure EZCAD2 software is running. |
| Overheating | Blocked ventilation, prolonged continuous operation. | Clear ventilation grilles, allow machine to cool down, ensure ambient temperature is suitable. |
10. User Tips
- For optimal results, always perform test marks on scrap material before marking your final piece, especially when working with new materials or designs.
- Experiment with different laser parameters (power, speed, frequency) to achieve various effects on different metals, such as color marking.
- Keep your workspace tidy and free of clutter to prevent accidents and ensure smooth operation.
- Regularly back up your design files and software settings.
11. Warranty & Support
VEVOR provides a one-year warranty for this Fiber Laser Marking Machine. For any after-sales problems, technical assistance, or warranty claims, please contact VEVOR customer support. Ensure you have your product model and purchase information ready when contacting support.