1. Introduction and Overview
The MinewSemi ME54BS01 is a highly flexible, ultra-low power, and cost-effective Bluetooth module based on the Nordic nRF54L15 SoC. It is designed to provide a robust and efficient solution for various Bluetooth Low Energy (BLE) applications, supporting the latest Bluetooth LE 6.0 Channel Sounding, Bluetooth Mesh, Zigbee, Thread, and Matter protocols.
Equipped with a powerful Arm® Cortex®-M33 CPU running at 128MHz, the module features 1.5MB NVM (Non-Volatile Memory) and 256KB RAM. It is also designed for PSA Level 3 certification, ensuring high security protection. The integrated PCB antenna and optimized design contribute to higher performance and efficient GPIO development.
Video 1: Overview of the MinewSemi ME54 Series BLE Modules, showcasing features and development kit compatibility.
2. Setup and Integration
2.1 Pin Description and Definition
The ME54BS01 module features 19 GPIO ports. Understanding the pin assignments is crucial for proper integration into your application circuit.
| Pin Number | Symbol | Type | Definition |
|---|---|---|---|
| 1/13 | GND | GND | Ground |
| 2-12 | P1.02-P1.06/P1.09-P1.14 | I/O | General IO Port |
| 14 | VCC | VCC | Power supply, default 1.8V-3.6V |
| 15-17 | NC | NC | Empty pins |
| 18-19 | P2.06/P2.07 | I/O | General IO Port |
| 20 | NRESET | Reset pin | Reset |
| 21-24 | P2.03-P2.10/P0.00-P0.01 | I/O | General IO Port |
| 25/26 | SWDIO/SWDCLK | Burn Pins | Programming pin, when programming, just connect the power supply pin, ground, and these two pins |
| 27-28 | P0.02-P0.03 | I/O | General IO Port |
2.2 Mechanical Drawing
The physical dimensions of the ME54BS01 module are critical for PCB design and enclosure fitting.
2.3 PCB Layout Guidelines
Proper PCB layout is essential for optimal performance, especially concerning the antenna. Avoid placing GND planes or metal cross-wiring in the module antenna area. Components should not be placed nearby. It is recommended to make a hollow or clear area, or place the module on the edge of the PCB board.
- **Antenna Clearance:** The module antenna area should be completely clear and not obstructed by metals, as this will negatively impact antenna performance.
- **Grounding:** Ensure the device is well-grounded to reduce parasitic inductance.
- **Copper Coverage:** Avoid covering copper under the module's antenna to prevent signal radiation issues and maintain transmission distance.
- **Isolation:** The antenna should be kept far from other circuits to prevent radiation efficiency reduction or interference with normal operation of other lines.
- **Placement:** The module should be placed on the edge of the circuit board, maintaining distance from other circuits.
- **Power Supply:** Consider using magnetic beads to insulate the module's access power supply.
2.4 Reflow and Soldering
Surface Mount Technology (SMT) should follow the reflow oven temperature profile. The maximum temperature is 260°C. Refer to IPC/JEDEC standards. Peak temperature should be less than 260°C, and the module should not undergo reflow soldering more than twice. It is suggested to perform reflow soldering only once on the module surface.
For partial ladder steel mesh, a 0.2mm thickness is suggested, with the opening extended by 0.8mm.
After unsealing, if the module cannot be used immediately, it should be vacuum-stored. Avoid prolonged exposure to air to prevent dampness and oxidation. If there is a 7 to 30-day interval before SMT, bake at 65-70°C for 24 hours without disassembling the tape. Always adopt ESD protection measures before SMT.
2.5 Development Kits
For easier development and prototyping, MinewSemi offers development kits. The ME54BE01 development board is available to assist with your integration and testing.
For more details or to order the development board, please visit the official MinewSemi website or refer to the related documents section.
3. Operating Instructions
The ME54BS01 module functions as a Bluetooth LE 6.0 receiver and transmitter, supporting various advanced protocols for IoT applications.
- **Power Supply:** Connect VCC (Pin 14) to a stable power source within the range of 1.7V to 3.6V. It is recommended to use a supply voltage not lower than 2.3V for optimal RF performance.
- **Grounding:** Ensure all GND pins (1 and 13) are properly connected to the system ground.
- **GPIO Usage:** Utilize the General IO Ports (P1.02-P1.06, P1.09-P1.14, P2.06-P2.07, P2.03-P2.10, P0.00-P0.01, P0.02-P0.03) for interfacing with external components and sensors. Refer to the pin definition table for specific assignments.
- **Reset Functionality:** The NRESET pin (20) can be used to reset the module.
- **Programming:** For programming the module, connect the SWDIO (25) and SWDCLK (26) pins, along with the power supply and ground pins.
- **Communication Protocols:** The module supports Bluetooth LE 6.0 Channel Sounding, Bluetooth Mesh, Zigbee, Thread, and Matter. Implement the desired protocol stack using the nRF54L15 SoC capabilities.
- **RF Performance:** The module offers configurable transmission power from -40 to +7 dBm. Optimize power settings based on application requirements for range and power consumption.
For detailed programming guides, SDKs, and example code, please refer to the official MinewSemi documentation and Nordic Semiconductor resources for the nRF54L15.
4. Maintenance
Proper handling and storage are crucial to ensure the longevity and reliable performance of the ME54BS01 module.
4.1 Storage Conditions
- **Shelf Life:** Use the product within 6 months after receipt.
- **Unopened Package:** Store the product in its original, unopened package at an ambient temperature of 5-35°C and a humidity of 20-70%RH.
- **Non-Corrosive Environment:** The product must be stored in a non-corrosive gas environment (e.g., free from CI2, NH3, SO2, NOx).
- **Mechanical Shock:** Avoid excessive mechanical shocks, sharp objects, or dropping the product to prevent damage to the packaging material and product.
- **Opened Package (MSL2):** After opening, the product should be stored at ≤30°C / <60%RH. It is recommended to use the product within 3-6 months.
- **Baking:** If the humidity indicator changes color or if exposed to ≥168h @ 85°C/60%RH conditions, or stored for more than one year, baking is recommended.
- Baking conditions: 120 +5/-5°C for 8 hours (1 time).
- Products must be baked individually on heat-resistant trays. Base tape, reel tape, and cover tape are not heat-resistant and may deform at 120°C.
- Alternatively, 90°C +8/-0°C for 24 hours (1 time). The base tape can be baked with the product at this temperature, ensuring heat uniformity.
4.2 Handling Conditions
- **Careful Handling:** Handle and transport products with care to avoid excessive stress or mechanical shock that may cause breakage.
- **Terminal Integrity:** Handle with care to prevent cracks or damages on the terminals, as this can alter product characteristics.
- **ESD Protection:** Do not touch products with bare hands. Static electrical charge can destroy the module or impair solderability. Always use appropriate ESD protection.
5. Troubleshooting
This section provides general guidance for common issues. For in-depth troubleshooting, refer to the comprehensive datasheet and application notes available on the MinewSemi website.
- **No Power/Module Not Responding:**
- Verify the power supply voltage (VCC) is within the specified range of 1.7V to 3.6V (recommended ≥2.3V).
- Check all ground connections (GND pins).
- Ensure the NRESET pin is not held in a reset state.
- **Connectivity Issues (Poor Range, Disconnections):**
- Review your PCB layout, especially the antenna area, to ensure it adheres to the guidelines (no metal obstruction, sufficient clearance).
- Check for external interference from other electronic components or metal objects near the antenna.
- Verify the antenna is not damaged.
- Ensure the module is placed on the edge of the PCB if using the integrated PCB antenna.
- Adjust transmission power settings if applicable.
- **Programming/Firmware Upload Failure:**
- Confirm correct connections for SWDIO and SWDCLK pins.
- Ensure the programming tool (e.g., J-Link) is properly configured and drivers are installed.
- Check for stable power supply during programming.
- **Unexpected Behavior/Crashes:**
- Verify that the module's operating temperature is within the specified range (-40°C to +105°C).
- Check for sufficient RAM and NVM for your application's firmware.
- Ensure proper ESD handling during assembly and operation.
- Consult the nRF54L15 SoC documentation for software-related debugging.
6. Specifications
The following tables detail the key parameters and electrical specifications of the MinewSemi ME54BS01 module.
6.1 Key Parameters
| Parameter | Value |
|---|---|
| Chip Model | Nordic nRF54L15 |
| Module Type | BLE Module |
| Module Size | 23.2 × 17.4 × 2 mm |
| Antenna | PCB |
| Flash (NVM) | 1.5 MB (1524KB) |
| RAM | 256 KB |
| GPIO | 19 |
6.2 Electrical Specifications
| Parameter | Value | Notes |
|---|---|---|
| Working Voltage | 1.7V-3.6V | To ensure RF work, supply voltage suggest not lower than 2.3V |
| Working Temperature | -40°C to +105°C | Operating temperature from -40°C to 105°C |
| Transmission Power | -40 to +7dBm | Configurable |
| Receiving Sensitivity | -96dBm | |
| Current (RX) | 3.2mA | RF receiving current under 1Mbps pattern |
| Current (TX) | 5mA | RF transmission current under 0dBm pattern |
7. User Tips
Based on common practices for integrating BLE modules, here are some tips for optimal performance:
- **Antenna Placement is Key:** Always prioritize the antenna layout guidelines. Even small metallic objects or ground planes too close to the antenna can significantly reduce range and signal quality.
- **Power Supply Stability:** Use a clean and stable power supply. Noise on the VCC line can affect RF performance and module stability. Consider adding decoupling capacitors close to the module's VCC pins.
- **ESD Protection:** Always handle the module with proper electrostatic discharge (ESD) precautions. Static electricity can permanently damage sensitive electronic components.
- **Software Development:** Start with the official SDKs and example projects provided by Nordic Semiconductor for the nRF54L15. This will accelerate your development process and ensure compatibility.
- **Testing Environment:** When testing RF performance, ensure you are in an open environment with minimal interference to get accurate range and throughput measurements.
8. Warranty and Support
MinewSemi is committed to providing high-quality products and technical support.
8.1 Quality Assurance
MinewSemi operates with state-of-the-art production facilities and a meticulous quality management system, holding certifications such as ISO9001, ISO14001, ISO27001, OHSA18001, and BSCI. Every product undergoes stringent testing, including transmit power, sensitivity, power consumption, stability, and aging tests, ensuring high-volume production demands are met.
8.2 Technical Support and Documentation
MinewSemi provides free technical support for the ME54BS01 module. For further assistance, detailed datasheets, application notes, and software development kits, please visit the official MinewSemi website.
You can view and download the latest product documents electronically, including the full datasheet, from the following link: ME54BS01-nRF54L15 Datasheet (PDF).
For product change notifications and regular updates of MinewSemi documentation, please register on their website: www.minewsemi.com.
8.3 Copyright Statement
This manual and all its contents are owned by Shenzhen Minewsemi Co., Ltd. and are protected by Chinese laws and applicable international conventions related to copyright laws.
The certified trademarks included in this product and related documents have been licensed for use by MinewSemi. This includes but is not limited to certifications such as BQB, RoHS, REACH, CE, FCC, BQB, IC, SRRC, TELEC, WPC, RCM, WEEE, etc. The respective textual trademarks and logos belong to their respective owners. For example, the Bluetooth® textual trademark and logo are owned by Bluetooth SIG, Inc. Due to the small size of the module product, the "Bluetooth" symbol is omitted from the Bluetooth Primary Trademarks information in compliance with regulations.
The company reserves the right to change the content of this manual according to technological development without prior notification. Unauthorized modification or use of this manual's contents is prohibited and will be held accountable in accordance with the law.