ZoeRax RJ45 Pass Through Connector

Contents

ZOERAX RJ45 Pass Through Connector User Manual

Brand: ZoeRax

Model: RJ45 Pass Through Connector

1. Introduction

Thank you for choosing ZOERAX RJ45 Pass Through Connectors. These connectors are designed to simplify the termination process for Cat5e and Cat6 Ethernet cables, ensuring reliable network connections. The pass-through design allows for easy verification of wire sequence before crimping, reducing errors and improving efficiency.

2. Safety Information

  • Do not use for live working to prevent electric shock.
  • The blade and crimping parts are sharp; do not touch them directly.
  • Keep fingers out of the blade and crimping die during operation.

3. Product Features

  • Wide Compatibility: Supports 24 to 26 AWG round or flat network cables. Cat6 23AWG solid cable is also supported. Maximum cable outer diameter of 1.10mm.
  • Pass-Through Design: Allows wires to pass completely through the plug, enabling visual verification of the correct wire order before crimping.
  • High Performance: Achieves better data transmission and supports speeds up to 1000Mbps. Backwards compatible with Cat5e stranded or solid cables.
  • Durable Contacts: Features 3-prong, gold-plated contacts (Phosphorus Copper, Nickel Plated Layer, 50µ Thick Gold-plated Layer) to enhance signal integrity and clarity by reducing the distance between wire twists and contacts.
  • Eco-friendly Material: Constructed from eco-friendly materials, designed to withstand over 45 bend times and a 180° bend test.
RJ45 Pass-Through Connector Diagram

Illustration of the pass-through design, showing wires extending through the connector.

3-Layer Gold Plated Contact Teeth

Diagram showing the 3-layer gold-plated contact teeth for reliable connection.

Eco-friendly Material Bend Test

Image illustrating the durability and bend resistance of the connector's eco-friendly material.

RJ45 Connector Wide Compatibility

Visual representation of the wide range of devices compatible with RJ45 connectors, including notebooks, industrial routers, switchers, and gaming consoles.

4. Package Contents

  • 50 or 100 x ZOERAX RJ45 Pass Through Connectors (quantity depends on purchase)

5. Setup & Installation

Follow these steps to properly terminate an Ethernet cable with the ZOERAX RJ45 Pass Through Connector:

Official video guide for RJ45 connector termination.

  1. Prepare the Cable:
    • Slide a strain relief boot onto the cable (if using).
    • Measure and strip the cable jacket approximately 3cm (30mm) using a cable stripper. Be careful not to damage the internal wires. The length of the stripped jacket should not be too long or too short.
    • Carefully cut off the cross filler and rip cord (if present) from the stripped cable.
  2. Arrange Wires (T568B Standard):
    • Untwist and arrange the 8 individual wires according to the T568B wiring standard. Ensure the wires are straightened to facilitate easy insertion into the connector.
    • T568B Wire Order (Left to Right): Orange/White, Orange, Green/White, Blue, Blue/White, Green, Brown/White, Brown.
    • Double-check the wire sequence for accuracy.
    • Obliquely cut the ends of the arranged wires to create a sharp tip, making them easier to pass through the connector.
    T568A / T568B Wiring Scheme

    T568A and T568B wiring schemes for Ethernet cables.

  3. Insert Wires into Connector:
    • Hold the RJ45 connector with the clip facing downwards. The first pin should be on the far left.
    • Carefully push the arranged wires through the connector until they exit the front.
    • Visually inspect the wire sequence again through the transparent connector to ensure it matches the T568B standard and that each wire is fully extended to the front. If the sequence is incorrect, remove the wires and re-arrange them.
  4. Crimp the Connector:
    • Insert the RJ45 plug into the cable cap (if using).
    • Place the connector into the crimp interface of your RJ45 crimping tool. Ensure the connector is fully seated at the bottom of the crimp interface.
    • Firmly squeeze the crimping tool handles until the crimping action is complete. The 3-prong blade inside the connector will make good contact with the wires and slightly depress.
    Crimping Tool Usage

    Image demonstrating the proper use of a crimping tool with the RJ45 connector.

  5. Test the Cable:
    • Once both ends of the Ethernet cable are terminated, use a cable tester to verify connectivity.
    • Connect each end of the newly made Ethernet cable to the respective ports on the cable tester.
    • Activate the tester. If all eight lights illuminate in sequence (typically green), your cable is correctly terminated and functional.
    • If any light fails to flash or the sequence is incorrect, re-check the wire order and crimping on both ends. If necessary, re-terminate the faulty end.
    Cable Tester for RJ45

    Image of a cable tester verifying the functionality of a terminated RJ45 cable.

6. Operating Instructions

Once your Ethernet cable is properly terminated with the ZOERAX RJ45 Pass Through Connectors, simply plug the cable into any compatible RJ45 port on your network devices (e.g., computer, router, switch, game console) to establish a network connection.

7. Maintenance

  • Keep connectors clean and free from dust and debris to ensure optimal contact.
  • Store unused connectors in a dry, cool place away from direct sunlight and extreme temperatures.

8. Troubleshooting

  • Connection fails to establish or is unstable: Verify that the cable termination is complete and correct on both ends. Ensure the wire sequence matches the T568B standard.
  • Cable tester lights do not all turn green: This indicates a wiring error or a faulty crimp. Re-check the wire sequence and inspect the crimping for any issues. If necessary, re-terminate the cable.
  • Intermittent network connection: Try restarting your router and re-testing the cable. Ensure the cable is not bent sharply or damaged.
  • Abnormal functionality: If you experience persistent issues, contact customer support for assistance.

9. Specifications

AttributeValue
Brand NameZoeRax
Interface TypeRJ-45
CompatibilityCat5e, Cat6 (24-26 AWG round/flat, 23 AWG solid for Cat6)
Max Cable Diameter1.10mm
Speed SupportUp to 1000Mbps
Contact Material3-layer gold-plated (Phosphorus Copper, Nickel Plated Layer, 50µ Thick Gold-plated Layer)
Durability180° bend test, 45+ bend times
OriginMainland China

10. User Tips

  • The pass-through design significantly simplifies inserting the desired cable length and can make the termination process easier.
  • Always ensure proper crimping technique and verify connection integrity with a cable tester to avoid faulty terminations.

11. Frequently Asked Questions (FAQ)

Q: Connection fails to establish?
A: Verify that the cable termination is complete and correct on both ends. Ensure the wire sequence matches the T568B standard.
Q: Cable tester lights do not all turn green?
A: This indicates a wiring error or a faulty crimp. Re-check the wire sequence and inspect the crimping for any issues. If necessary, re-terminate the cable.
Q: Unstable network connection?
A: Try restarting your router and re-testing the cable. Ensure the cable is not bent sharply or damaged.
Q: Abnormal functionality?
A: Contact customer support for assistance.

12. Warranty & Support

For warranty information and technical support, please refer to the official ZoeRax website or contact your retailer. A detailed user manual (PDF) is available for download at https://manuals.plus/m/ec8e7db63ea941536b7c29522d63b4712bd5f2bf6cb885192c9b5d057556e0f0.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.